The CJ3A Page CJ3B.info

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Doug

Pages: [1] 2 3 ... 7
1
"Original"-- Technical Questions, Answers, Observations / Re: No fuses ?
« on: November 12, 2010, 10:03:18 PM »
The headlight switch has an automatic circuit breaker.   However, only certain components (those that draw their power through the headlight switch junction board, are then breakered.  Mainly the headlight, tail lights, and I think horn and possibly the ignition are protected.    Other components such as ammeter, and other wires, really have no circuit overload protection at all.  If one of those was to short, say to the dash board from a loose wire, it would just continue to short until something burned through.   To avoid that unpleasant scenario, I varied from the original design by adding a "fusible link" as a fail safe where the main wire supply comes off the starter and feeds the ammeter on the dash.  A fusible link is used on more modern cars even with fuses.  It's the circuit breaker or fuse of last resort and cuts all power to the jeep.    That way if there is a short to the dash say from an ammeter wire, the fusible link could burn through and cut the electrical supply.  A fusible link is available for about $3 and is merely a piece of short wire that has a rated capacity before it burns through.  Just my suggestion.    Without a fusible link, if there were a short, the only way to stop it would be to disconnect the battery cable.  Not a fun task when the sparks are flying and wires sizzling.  

2
Hi guys.  I have not been on the site in months.    Glad to be back.  Hope you are all doing great.   I need some fast help.  I am towing my jeep on a trailer 500 miles.   For the first time, I plan to do it correctly with the windshield folded down.   Problem is I have a new windshield strap from walcks and for the life of me, I cannot figure out the proper way to run the strap ends through the buckle.  Does any one have a close up picture of the proper way to run the straps through the buckle?   I am leaving tomorrow morning at 10 am.   Thanks and glad to be back on here.  
Your friend.  Doug.

3
Have not been on here in months guys. � I offer my two cents. �The two cups you talk about might stop a tiny bit of leaking from the shifter, but not the tranny.

My tranny leaked from the input shaft like crazy. � Replaced the felt seal twice, even doubled up on them one time and it kept leaking like a sieve. � Then I looked inside my tranny. �I noticed in comparing to engineer drawings that there were two different engineered drawings. One willys drawings shows an oil slinger washer, similar to those in the differentials, at the input shaft. �The other willys drawings does not show it. �I took my tranny apart enough to install the oil slinger, returned the felt seals back to factory, put it together and my input shaft has not leaked a drop of oil in four years. � The oil slinger was keeping 99% of the oil �off the felt seal. �Then only 1% gets on the felt seal, just enough to keep it lubricated. �I think a lot of trannys are missing the oil slinger washer at the input shaft. �Try that. �

For leaks at the sealing joints between the transfer case and tranny, it is important to have them planed flat before mating. �Over the years they get warped from overtightening the bolts. � Hope that helps. �Doug.

4
Larry, I have seen some heads where all the holes were blind bolt holes.  For what it's worth, on many of the heads the bolts are through bolts to the water jacket.  My Willys civilian head and a GPW head in my possession both have two of the three bolt holes open to the coolant below.   I wish there were all blind because mine have been an occassion for leaking and requiring resealing.  




I counted the threads and there was a total of 7-8 threads in each of the through holes.

One other thought on this subject, sometimes machine shops will burn a really stuck low grade steel bolt out of a cast iron block with a oxy torch, I think as a last case scenario.   Machine shops have 5 tricks for everyone one that the non-expert has.

5
If you cannot get the broken bolt out, you can use a washer under the bolt head to take up the slack so that it will tighten down. �If you are sure it is a bolt that is broken off down in the hole, you could use the drilling and picking technique others mentioned to try to get it out or just try to use it as it is and don't overtighten that bolt.  Also, as others mentioned, there is always a machine shop.  What is a major undertaking for us and a nerve racking event, is just another 30 minutes work for a machinist.   For example they would be using a drill with a base rather than a hand drill, they would have reverse thread bolts, they could put heat to it with an acetylene torch, etc.    It may cost you $40 or $80 but it may make you feel better.

6
Depending on the luck of the draw, some of those outlet mounting holes are through holes and some are blind holes.  Just depends on your particular casting and how far they were drilling that day at the factory.   Look through the round opening and see if you can see the bottom of the bolt.  Can you reach through the water outlet hole and try to back it out?    Are you sure it is a bolt you are seeing or is it simply the bottom of the hole.

When you say the bolt is shorter because it is bottoming out on an old broken off bolt, just how long is the bolt you removed?  How many threads were holding.   This is not a motor mount it is a water outlet elbow under 5 psi pressure held down by three bolts.  It may be fine if the bolt you removed is long enough to hold.   Probably 4 or 5 threads is enough to hold.

7
when you replace the thermostat, do not get the cheap one sold at walcks. �It does not contain an air relief valve and will allow an air pocket to form at the top of the engine and allow it to vapor lock and overheat. �Get a thermostat with an air relief valve. �About $2 more. �These tall engines are prone to form air pockets. �The little 1/8" diameter brass tab in the theremostat is the air relief valve. �





8
Jamesr, I did the same thing with a 77 old style bronco with two tanks.  I was testing it for a week before buying.   Drove one tank empty and flipped the switch on the dash to go to the other tank.  Little did I know, it had a dash switch for the electric gauge and a mechanical valve coming through the floor below the drivers seat to actually switch tanks.   So gauge said full, but not gas flow.  Engine died.  Killed the battery trying to crank it, got dark, called a tow truck, paid to have it towed, and two days later found the other valve.   Doohhhhhhh!   I ended up buying it.   I finally sold that bronco about ten years later.  Sometimes, I wish I still had it, until I recall how it wanted to roll over at highway speed (lot worse than my cj3a), so probably good I do not still have it.  

9
Either way you go, you are going to need access to a mig welder and someone who knows how to use it. �With the replitub it will be minimal but still needed. � If you have a mig welder and you miss drill a hole, they are easy enough to fill. � �There are lots of poeple around with small mig welders. �And you do not need an artisan, just someone with some basic welding skills. � So either way you go, I would start looking around for someone with some welding equipment and basic skills. �You will need it before you are done. � � I ended up buying my own and teaching myself some welding. � That was probably more expensive route but I wanted the learning experience. � You can rent them pretty cheap too. � �But you have to know a little bit about using a welder. � Fixing the e brake to factory style is not rocket science,  finding the bracket and welding upside down are the hardest part of that task.   If I had known about it in advance of mounting my tub, it may have been easier to weld with the tub on its side or even upside down.  If you are a stocky built guy, you will not enjoy wedging yourself under the dash and trying to weld with the welding tip inches from your face.  

10
I have found the best thing for those rusty bolts is a 11,000 rpm angle grinder and a drill bit. � �If I had the money it would be a plasma cutter instead!!!! Sometimes it's just not worth trying to unscrew a rusted nut and bolt. �Now if it is in a critical place like engine or tranny block, then you have to be careful and get it out. �But on the frame, I use the big hammer principal of mechanics to strip it down. �Keep us posted with pictures. �Have lots of fun!!!!!

11
Nice looking rolling chassis.   You are getting to the fun part.  Every time I see a CJ3A stripped down to the chassis, I start salivating and looking for my wrenches.    Good luck.

12
And like someone said get the good rubber hoses from Walcks made in America not those cheap nylon ones from omix ada.    The cheap ones will explode, especially the one from the supply galley to the filter. When it busts oil goes everywhere and it will defintely bust if you use the cheap lines.    

13
Hate to throw cold water on the idea of pursuing them, but in addition to the things that the other folks mentioned like difficulty of proof, variables in installation etc,.    Even if you were somehow to succeed, their is probably fine print in their warranty that states that even if they are liable, their damages are limited to the cost of the parts sold.  They almost assuredly limit their liability for labor, incidental and consequential damages.  

By the way, as a side note, the last couple gasket kits I bought from felpro contained only the rope seal.   I had to buy the rubber from a separate supplier.  So apparently, felpro is being proactive to avoid further future claims  by getting out of supplying the seals.  

If I were you, I would forget about the suing idea, and would instead call fel pro and see if they would work something out with you.   You never know sometimes a company will help you out.    Especially if they recognize they had a problem (why else would they quit selling the seals).    Good Luck.  Doug

14
I had looked all around for a new flapper.  No one seemed to have one.   The best I could find was an old one that I could cut the old shaft out of and then weld back together over the new shaft.     They are producing complete units out there that include repop flappers so you would think someone is making them out there.  But I never could find a source to buy just the flapper plate alone.

15
Not only are the NDCC supposedly quieter on the highway, but the more important reason, supposedly safer.   The idea being that the NDCC tires would ride on the center of the tire on the highway and the square shoulders usually seen on an NDT would not grab on the edges and pull the vehicles to one side or the other as much.  

Pages: [1] 2 3 ... 7