The CJ3A Page CJ3B.info

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - smrmedic

Pages: [1]
1
Your CJ-3A Project / Re: 1950 CJ3A ROCK CRAWLER BUILD
« on: January 03, 2020, 12:32:16 AM »
Thanks Oldtime. This is the kit I bought from Herm to put in the axle.
"CJ rear disc brake kit + D44 Full floater kit + New 30 spline D44 PowerLock"
I also got a new yoke and new 5.38 gear set. I haven't set up gears before so I bought 2 bearing sets with shims and seals so I can ream out one set to use for set up bearings. It was cheaper to buy the whole set than the individual bearings.
The dana 44 axle came with a dana 27 with disc brakes in a package deal. Both have 4.88 gear sets. I'm not using the 27 though. I'm going to find a dana 44 for the front also since I am running 35" tires. I'm planning on using an OX locker for the front. I haven't decided for sure what type yet, manual, electric or air. I need to study more. I want to have a selectable locker for the front.

2
Your CJ-3A Project / Re: 1950 CJ3A ROCK CRAWLER BUILD
« on: December 31, 2019, 11:56:44 PM »
I found a dana 44 out of a 69" cj5 so I'm going to pick it up tomorrow. From what I have read it is the same width as the 41 so all of my parts should work. Thanks for the Information Oldtime.

3
Your CJ-3A Project / Re: 1950 CJ3A ROCK CRAWLER BUILD
« on: December 31, 2019, 11:00:32 PM »
I just checked the carrier in the case again. I see what you meant about the locker not fitting. The locker body itself is too wide. It hits the bearing mount on one side. I guess it is time to look for a 44 for the rear. I have been thinking about going a little wider anyways. Thanks for the information. I really appreciate it.

4
Your CJ-3A Project / Re: 1950 CJ3A ROCK CRAWLER BUILD
« on: December 31, 2019, 10:36:56 PM »
I'm new to this axle so I appreciate any help and information.
Thanks.

5
Your CJ-3A Project / Re: 1950 CJ3A ROCK CRAWLER BUILD
« on: December 31, 2019, 10:32:58 PM »
Here is a case picture.

6
Your CJ-3A Project / Re: 1950 CJ3A ROCK CRAWLER BUILD
« on: December 31, 2019, 10:31:20 PM »
The inner diameter of my ring gear is smaller than the powerlock carrier. It won't fit onto the carrier. The bolt holes have a smaller radius from the center as well. T he powerlock carrier seems to fit the case. I checked the new carrier bearings and the carrier width in the case. Maybe the case is a 44 but the shape looks like a 41 in the pictures and the 44 gasket doesn't fit.

7
Your CJ-3A Project / Re: 1950 CJ3A ROCK CRAWLER BUILD
« on: December 31, 2019, 04:52:45 AM »
I was rebuilding my rear axle only to find out that it was a Dana 41 instead of the Dana 44 I thought it had. According to the information on the dana 44 tech site it should have been a dana 44.

" The Dana 44 was introduced in the CJ line on the CJ-3A starting with serial number #37549 (late '50). Earlier CJ-2As and CJ3As did not use the Dana 44."


My serial number is "43951" but it has a dana 41. The D41 uses a smaller ring gear that won't fit the newer D44 30 spline locker. The locker is the same width as the D41 carrier from what I can see. I also had to swap my yoke from a 10 spline to a 26 spline to fit the new pinion. The full floater kit I purchased from Herm uses 30 spline axle shafts. I purchased the powerlock with the full floater kit to match the axles. I also purchased the disc brake conversion kit with it as a package deal. With all of that combined with my axle truss should make for a much stronger set up.

The housing cover gasket is different too. Luckily I hadn't opened the lube locker gasket package yet so I am able to return it on Amazon. Hopefully I can return the 10 spline yoke as well.

I should have looked at the axle closer to begin with instead of just using what I read.

Hopefully this information can help others. I'll post more information as I go along.

SMRMEDIC is my screen name. I wasn't able to use it in my first post because it hadn't been approved yet, in case anyone noticed the difference from my first post.


Pages: [1]