The CJ3A Page CJ3B.info

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Squishymonster

Pages: [1] 2 3 ... 7
1
Your CJ-3A Project / Re: project: crunchy roll (53 cj3a)
« on: September 02, 2021, 03:11:29 PM »
I wanted to rebuild my rear seat mounting system and frame so that it could be easily removed for hauling hay with the tailgate down. I finally got a workable tubing bender that can handle up to 1 inch. I designed a custom frame that uses the original mounting points in the bed, and fits in a similar fashion. I made custom rear pins or studs that bolt into the rear seat retaining clip holes - I don't have the original retainers, and didn't want to spend what "they" are asking. So I made the studs fit up inside 1 inch tubing and they will use 1/4" through-pins to secure.

Everything came together really nicely, and I'm happy with how the CJ5 vinyl seat mounts to it. I could not retain the tilt forward functionality - or at least not without more effort than I wanted to expend, but it is fully removable without tools. It sits slightly higher and further back than previous, so I'd say leg room is maximized without having the seat in a weird spot.

I'll get photos soon.

It's all back together except I still need to reattach the muffler - I need to come up with a better way to mount that too. I had the compression fittings on there that kink the outer tube, and the stupid things were jammed together permanently. I had to cut a slot in one tube to get them apart, and I want to make that easier to get apart for next time I need to do maintenance under the bed.

I also made some custom rubber body mounts for the two bed mounts - I think they are the only two functioning on the whole vehicle ATM.

I pulled / repaired a minor but annoying dent and split in the rear left quarter panel that was contributing to a very slight amount of the rear body sag. I have nearly all of the major body damage straightened out at this point - at least rouged in, and I'm really happy with it. I think I'm 100% ready for the Best Top install, and just in time for Fall.

In my efforts to hunt and destroy rattles, I pulled the left and right windshield frame topper strips out, and they are being repaired. One was screwed in, and the other was held on by one weld, so it was jiggling all the time. I mangled one of them a good bit, but almost have it back into shape. It's going to require some MIG finesse to repair properly though - some really light beeds so I don't have to destroy the track with a grinder afterward.

I'm feeling like next steps might be repairing some of the bigger rusted spots in the floor - my 2.5yo daughter loves to climb around in the jeep while I'm working on it, and I'd like to get rid of things that could get her snagged up.

2
Your CJ-3A Project / Re: project: crunchy roll (53 cj3a)
« on: August 20, 2021, 11:30:04 AM »
This is sort of a non-update...

When I bought the 53, I put the purchase, transportation, and the full round of initial parts on a credit card. I gave myself a 4500 budget - close to what I thought I could get by selling my 2011 KLR650. It's been two years. I've been carrying the CC balance since. I finally just followed through with selling the KLR yesterday evening - a sad day for sure :)  But it does feel good to have one less set of wheels cluttering up the brain, and having a little more mental focus on the CJ.

I had not registered the KLR since 2018, and only put a few miles on it since to keep fuel moving through it and make sure it stays operating well. I decided to sell it and switch to a CJ when our daughter arrived - knowing that my days of taking the wife out for back road cruises were over for a while, and we'd need a 3rd seat in the near future!

Speaking of seat - I need to bend up a new rear seat frame and I FINALLY found a not too expensive tubing bender that works. I tried the Harbor Freight pipe bender and hate it for this task (which it was not designed for). It had been very hit or miss, and I'm not a big fan of wasting material until one happens to come out right.

So next steps are to design a new frame, bend and weld it. I am considering the idea of making the rear seat reversible. The main thing is when I had to unbolt the previous custom seat frame it was a little too much of a PITA to get to the bolts - so this time I want to make it easy to pop in and out - closer to stock, but still with a reinforced seat belt bar, and of course with the belts, it needs to be mounted to the floor strong enough to actually hold together if there was an accident.

I got the body straight now, which means the tiger top can go on, which means I can figure out dimensions for a roll cage. But I can't bend a roll cage myself, so I think I'm most likely going to get a pre-formed kit that just needs welding.

3
Engine compartment / Re: 61 CJ3B Stalling and now Dead
« on: August 20, 2021, 11:18:07 AM »
For my own experience "charged the battery" is almost always the failure point. Batteries go bad and won't take a charge. I'd use a multimeter to check that the battery voltage is actually there. If not, replace it. This is especially true for a battery that goes a full season or two without being used at all - especially if your Willys happens to have a small closed circuit somewhere. Otherwise you get to debug some wiring.  :D

One unfortunate thing I've experienced TWICE in the last couple of months with trailer wiring is that water and corrosion can be drawn WAY up inside of a wire from an exposed end, and rot it for several feet, making it unable to carry a current. So just because a wire is in place and "looks solid", doesn't mean much. If you don't find any obvious breaks in the circuit to the starter then you might need to use  your multimeter to do continuity and/or voltage testst across each length of wire - as others have suggested.

But, based on your description it sounds like you could have both an electric and fuel problem, though it is possible to get all of these symptoms just by electric.

Once electric is out of the way, drain the gas from the carb bowl into a clear jar and look for a layer of water on the bottom. The water will get pulled into the engine first, and depending on how much is there (hopefully none) will cause run / stall / run / stall situations. If there is water in the bowl, there is water in the tank, lines, filter, and pump, so the whole thing needs to be well drained. Water sinks in fuel so it will go to the lowest possible spot, and wait for you to add fuel on top of it. It's "neat"

4
Your CJ-3A Project / Re: project: crunchy roll (53 cj3a)
« on: August 09, 2021, 12:54:27 PM »
It took two or so weeks of prep but I finally unwound the various body damage enough to fix the main problem - the rearear right fender being welded on at the wrong angle and height.

My bed is still pushed down, but I was able to get the flanges very straight amd plug welded from inside the wheel well.

I did some shoving of the bed to get it "more flat" but it is way off still.

I also discovered the extent of a poor repair to the left frame  towing bracket - its welded on just in the totally wrong spot and angle. But it's going to be pretty hard to solve with the body on, so I think it will wait for now.

Next steps are to bolt everything back together, and probably take a shot at a more elaborate rear seat bracket that can be taken out without tools.


5
Buy, Sell, Trade / Re: Tailgate from 1961 CJ5
« on: August 06, 2021, 10:19:35 AM »
I'm fairly new at "hobby" level metal work but I'd say that's salvageable for sure.

If someone wasn't too worried about perfectly stock contours, they could weld in an off the shelf steel tube at the bottom. If someone wanted it to look stock they could rig up a fairly simple jig to get that bend.

I wouldn't toss it. I tossed a couple of parts years back before a learned what is really possible and I still get mad at myself about it :)

6
Your CJ-3A Project / Re: project: crunchy roll (53 cj3a)
« on: August 04, 2021, 10:52:44 AM »
This is a nice milestone. Finished prepping and patching this inner corner on the rear right bed opening. Lifted and twisted it into place and welded the split framing back together. It's holding the angle on its own, but I still need to put on the body to cross member mounts, and weld about half the right side bed to fender flange - after straightening.

This is all working toward a straight corner to mount my Bestop too.

7
BODY and trim / What factory color is this?
« on: August 03, 2021, 10:51:45 AM »
This is a 53 cj3a. It is a civilian model, Navy registered. I read elsewhere that they were prepared by the factory for base use. It has the Navy brass id tag on the dash.

The color in places looks like it's been spray blasted with a not quite matching whiter/flatter version of this "sky blue". But overall this color in the photo seems to be stock. The underside of most of the Jeep still has this thin layer of rough-texture undercoating that is peeling off in places, and the paint way up on the hat channels etc where the undercoat is peeling off is pristine like-new blue. It looks like about a semi-gloss.

I'm not doing a full restoration, but I am attempting not to make any permanent changes that would make it unviable as an authentic restoration. As an example, I'm using more modern CJ seats, but they are just bolt on and can be swapped out if someone down the line were interested in going more original.

Likewise for the body, I'd like to "honor" the original intent of the vehicle since it is rare- keep the navy registration numbers and the color while I'm making spot repairs. Ideally I'd love to use just spray cans but I'd order the paint special if that's what it takes.

While we're at it, I'd like to take the paint off all of the vinyl(?) registration numbers on the hood and tailgate, ideally without ruining the vinyl - and without having to paint them in / replace them if possible. Any suggestions for safely cleaning those up?

8
Your CJ-3A Project / Re: project: crunchy roll (53 cj3a)
« on: August 03, 2021, 01:09:41 AM »
Oh yeah. I realized why I can't remove my tailgate without removing the hinge bolts: the hinges are strap steel someone twisted around some rod and then sawed in half :p. Cast iron eplacements are waiting in the parts pile.

9
Your CJ-3A Project / Re: project: crunchy roll (53 cj3a)
« on: August 03, 2021, 12:53:27 AM »
Long break due to lack of funds for transmission / xfer gear sets.

Finally decided I don't need much cash to do body work.

Rear Lower "skirt" was all smashed upward. Rear right quarter panel was half ripped and twisted off from tire carrier related stress, and a PO crap welded it back against the bed flange two inches low and lopsided. Finally decided to cut the welds and tackle it. It's almost in the right spot now. Bodywork is still lumpy but it's structurally sound.

Next step: flatten the bed enough to line up the flanges properly and plug weld.

Also hand fabbed a Rear body mount bracket (and killed another vice)

As usual I'm having a hard time posting the photos. I'll try again tomorrow.

Really having fun with the body work and light fab. Trying to figure out how to undo this mess is a fun puzzle.

Now that things are a bit straighter, the rear body is 1/2 inch off the cross member. Trying to make sense of that considering the bed is sagging a solid inch...

This is somehow related to the body lean.

10
BODY and trim / Re: Top Stowage Ideas
« on: July 06, 2020, 02:06:16 PM »
maybe overkill / expensive, but I've seen zip up black nylon roof rack bags that might be about the right size. Mice can chew through it though if they are so inclined.

11
Your CJ-3A Project / Re: project: crunchy roll (53 cj3a)
« on: June 29, 2020, 10:57:33 AM »
I'm at my parents for the week and finally brought my trailer up to scoop up the 48 CJ2A engine/trans/transfer. The plan is to rebuild these one by one and swap them in.

In other news, my custom reciever bent my bumper a bit due to the weight of the hay on my trailer. I'm going to plug in a heavy piece of channel to beef it up a bit.



12
Willys photo and story threads... / Loading hay
« on: June 14, 2020, 10:05:03 AM »
I had just finished a hitch receiver yesterday afternoon. Then it just so happened that our hay guy got our field cut. The bails were sitting out there all afternoon then we realized rain was coming so we put the 53 to work. 140ish bails, 6 trips with a 4x8 utility trailer. Use what you've got :)


13
Your CJ-3A Project / Re: $2000 project?
« on: June 13, 2020, 06:14:06 PM »
Yeah if its running even a little, body is in one piece, and the frame isn't hacked up, its worth around 2k. Be prepared to spend a lot more getting it roadworthy. Its not unusual for literally every part to be worn out.

14
Your CJ-3A Project / Re: project: crunchy roll (53 cj3a)
« on: June 13, 2020, 05:22:46 PM »
Just finished a custom receiver.


15
Your CJ-3B Project / Re: CJ-3B 57348 69050
« on: June 03, 2020, 11:41:32 AM »
re: Plan B, I was thinking about putting a receiver on the back bumper for a bike rack :D And putting tow-bar mounts on the new front bumper. Ride the bike home, get the daily driver, and go out to retrieve.

I bring my wife and 16mo for short Sunday rides but I'm not venturing more than 5 miles out in case something breaks. But if I can stick both of our bikes on the back we will be in good shape. My bike has a kid-seat on it already so instant emergency escape-pods with a bit of unplanned cardio. :D

Pages: [1] 2 3 ... 7