The CJ3A Page CJ3B.info

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - 51USNCJ3A

Pages: [1]
1
Your CJ-3A Project / Re: ?Another 1951 USN CJ3A?
« on: April 29, 2020, 10:46:19 AM »
Mine is a 53. On each side of the hood It has US NAVY over the numbers. The text ends up being on the top surface of the hood and the numbers wrap the contour and end higher than the willys lettering.

If you go to my "crunchy roll" thread and zoom in on any hood shots you can somewhat make out the faded lettering.

I believe my paint is original in places too. The firewall is a grey blue. It looks flat or semigloss. I think someone spray bombed a lot of the accessible surfaces with a close but not quite matching color.

Thank you. It looks like our Jeeps are about 1 year apart in age.

2
Your CJ-3A Project / Re: ?Another 1951 USN CJ3A?
« on: April 25, 2020, 11:35:53 PM »
Okay, so it is pretty obvious that I didn't keep up with progress pictures. However,  if you all are willing to overlook that, I would like advice on placement of the hood numbers. I have seen some different configurations. 

USN 94-xxxxx

Or

 U.S. Navy
94-xxxxx

I am not sure how to proceed.

Thank you in advance
Mike



3
Thamks again.

You are right about the dimples. I had not noticed that.  Bob W. Did the Navy 3A's have Willys on the tailgate?

Linkage will go, and the floor will be repaired.

Mike G.

4
Your CJ-3A Project / Re: ?Another 1951 USN CJ3A?
« on: October 01, 2019, 11:10:40 PM »
Here are a few before pictures.  This is how I brought it home. 




More pictures can be found where I am learning what all I have in this Jeep.

https://cj3apage.com/Forum/index.php?topic=4367.0

Mike G.

5
Thank you athawk11 and Bob W. 

Here are some pictures of the casting numbers and other features of the engine.






Here is the starter from top and bottom, as well as the linkage that crosses over the transmission. Try not to be too jealous of my washer welded on for a gas pedal.





When I look closer, I can see that the steering gear is not stock.  Any ideas on where to find one of those?  Used I presume.

The tailgate.....  If it were easy, that article we both linked to would have had the answer.  I am quite familiar with aftermarket parts of today. I assembled a 1977 Bronco body from 100% repo stuff a couple winters ago.  This tailgate might be repo stuff from the '70's, not from any time recent.  What trips me up are the brackets spot welded to the inside.  Do they at least look like brackets that are known?  The fact that they are there, and have zero holes through the tailgate seems odd.  Why would aftermarket add those?  A mystery. 

I will share progress on the project page in the conversation I started over there when progress actually happens.  First, I have a corn crop that needs picking...

Mike G.

6
First off, I have searched and read a lot since I have found this forum.  Thank you to all who have contributed. I come to this with experience in AMC and newer Jeeps, but this is my first Willys. (Are they like Lays potato chips?)  First off, this is the 608th CJ3A made as a 1952. My username is off, because the title states that it is a 1951. I believe this stems from the fact that it went into the US Navy in 12 of 1951. I assume the Navy sold it as a 1951.  I am not particularity worried about that aspect. I have the full Navy dataplate and it completely matches the Willys plate on the firewall.  I have found that there are a few of these CJ3A's that served non combat use in the USN, but not sure what role this Jeep played.  I have read that 3a's the USN ordered, had the bottom mount radiator.  This Jeep appears to support that.(pardon the pun) I am not aware of any other special equipment that the USN 3A's received.   

Here are a few pics, and the list of obvious changes over the years:
Seats
Steering column/wheel.
Front bumper.
Top bows.
Several switches/gauges
Selecto hubs.
Warn OD.
Carburetor.
Radiator.
12V with Alternator
Small Flange block with 1948 head casting number.  (block numbers question below)
Fuel tanks and loss of tool box.
Custom Yellow paint.




 I believe I have figured out several things, but have a few questions:

1) Can anyone shed light on the tailgate?  It doesn't match any of the options I have found here:  http://cj3b.info/Dating/DatingTailgates.html    The brackets on the inside are definately spot welded on like a factory would do. However, there is no Willys script, or "notches" on the outside... 




2) Does this all look like a bottom mount rad crossmember to you?  (clearly, I understand that the cross flow isn't original)


3) Steering box/ column.  I am pretty sure chrome is wrong. Steering wheel is wrong.  Question: is the box also wrong? The floor is sure chopped up around the column.




4) Engine block is a small flange variety.  Head had a casting date in 1948. Number over the water pump is all gone but for a 2. I assume that this stems from machine work on the 'deck'. There is a number stamped on the RH side, front, just below the head. Anyone know if this number means anything?



5) The foot starter has a bell crank arrangement that moves the "button" over very close to the gas pedal.  There is a lot of holes torched into the tub on both sides of this.  Seems wrong to me. 




That is the bulk of the questions I have now.  I am sure there will be more later....  Plans for it? restore it to it's US Navy appearance. I do not plan to swap out the carb or the block unless they are somehow failing to perform.  I want it to be 'stock', but not 'take it to military shows and have everything perfect'. My Vietnam era Navy veteran is quite excited to see something besides Olive Drab in parades.  Heck, he is having trouble finding Jeeps at all for parades.  I suspect that is what this will mostly do.  I will own it, but, I feel that it really belongs to those who have served. I will make it look as close to original as possible, put as nice a paint job as seems prudent(thinking I will need a really tough base clear or single stage), add the numbers and loan it out every time I am asked.

Here are a few shots of the original gray.




Thank you in advance,
Mike G.

7
Your CJ-3A Project / Re: ?Another 1951 USN CJ3A?
« on: September 17, 2019, 10:39:55 PM »
I am sure that I will be asking a bunch of questions as I go forward. I plan on finding the right parts where parts are missing, but no replacing parts that are wrong, but there. The air filter comes to mind. It has a paper element on top of the wrong carburetor right now. Gloss paint makes me happy. I was hoping that would be the answer.

mikE

8
Your CJ-3A Project / Re: ?Another 1951 USN CJ3A?
« on: September 16, 2019, 09:01:31 PM »
It is.  Practically speaking will that make any difference for parts used? Like I said, It's am very new to this vintage. Also, since it is a CJ made for the Navy, would it have shiney or flat paint? 

mikE

9
Your CJ-3A Project / ?Another 1951 USN CJ3A?
« on: September 16, 2019, 02:42:26 PM »
Hello,

I am new here, and new to Willys Jeeps.  I have owned CJ5's on up, but that is all AMC and newer stuff.  However, I have just purchased, but have yet to take delivery of, a 1951(this may be disputable) CJ3A with a Navy data tag that matches the Willys body tag.  I have searched on here a bit and found a couple discussions of Navy 3A's.  The information in those discussions echos that on my Jeep.  I have included a picture of the Navy tag below.  Thoughts?

mikE 

Pages: [1]