My Willys 3A and 3B Community

3A, 3B, DJ Technical Knowledge Base => "Original"-- Technical Questions, Answers, Observations => Topic started by: athawk11 on May 25, 2014, 10:02:28 AM

Title: Clutch Pedal Link
Post by: athawk11 on May 25, 2014, 10:02:28 AM
On one of my chassis runs with Whitey, I pressed on the clutch.� All of the sudden�bammm!� Pedal went to the floor.

Whitey�s link is the primer red one in the photo.� I was a mile away from my house when this happened.� I walked home, grabbed the link off ODie, (Green one in the photo) and used it to get Whitey home.

Because I do believe the Willys engineers were smarter than me, I made a new traditional link (unpainted one in the photo), but then decided to 'upgrade' this link.� Many of you have done this already.� I held out...until I was stranded.�

I made one for Whitey and ODie.� I�ll keep the traditional links in my on board parts selection just in case another Willys Jeeper breaks theirs along a lonely mountain trail�

(http://i1195.photobucket.com/albums/aa397/athawk11/athawk11%20Willys%20White/ab6352d062adcad2c18c7c2af98cbee5_zps32e93d6a.jpg)


All painted up and ready for installation�



(http://i1195.photobucket.com/albums/aa397/athawk11/athawk11%20Willys%20White/fe092d0bac14f9f725ab1463f5de7f65_zps138d6edd.jpg)


It's a pretty easy project, and will give you a sense of security when used on your Willys.� Or, Have a traditional spare link with you at all times. ;)� It is, after all, the "Weak Link" in the clutch pedal equation. ;D

Tim

OOps.  Not pictured are the required clevis pins and cotter pins. :-[
Title: Re: Clutch Pedal Link
Post by: bretto on May 25, 2014, 02:08:00 PM
That's what mine has to, far superior to the stock design.  After buying a new replacement back when I was doing my restore, I realized how poorly that design was.  When you have the tub off, you can see how it flexes.  With the clevis setup, it's a solid straight pull.
Title: Re: Clutch Pedal Link
Post by: 1955CJ-5 on May 25, 2014, 04:25:31 PM
That is a great idea....it never even crossed my mind...

5/16 rod?
Title: Re: Clutch Pedal Link
Post by: Carls_jeep on May 25, 2014, 06:02:03 PM
Hmm, I'll have to put that on the to do list.
Title: Re: Clutch Pedal Link
Post by: athawk11 on May 25, 2014, 06:19:56 PM
This is not my idea.� I have seen this discussed on a number of Willys sites.� It's clearly a wear point, but I never thought the rod would just, break.

It is 5/16" rod, with 24 fine threaded ends.� Got the clevis ends on Ebay after stopping in at Napa.� (They only had one...and it was at the warehouse)

I have them installed now, but we are currently receiving about an inch of hale, so the test run will have to wait a bit.

Tim�
Title: Re: Clutch Pedal Link
Post by: gmcjr on May 25, 2014, 07:05:49 PM
Good Fix!
Title: Re: Clutch Pedal Link
Post by: BMIC on May 26, 2014, 12:34:33 PM
Thanks Tim, I will add it to the punch list before the tub goes on...
Title: Re: Clutch Pedal Link
Post by: 1955CJ-5 on May 26, 2014, 07:20:04 PM
Tim,

Is this the jeep that had the heavy duty 9 1/2" clutch and pressure plate?

When I got it my jeep had a replacement rod that was threaded on one end, and had a 90* fitting like the one on the throttle linkage..

I replaced it but I will now replace the replacement.....
Title: Re: Clutch Pedal Link
Post by: johnrb3b on May 28, 2014, 08:33:01 AM
Do you have a link to where you got the brass clevises?
Title: Re: Clutch Pedal Link
Post by: athawk11 on May 28, 2014, 01:12:52 PM
Hi Randy,� The broken rod happened on Whitey with the HD clutch and pressure plate.� I think this would be similar to the clutch on your CJ5.

John,
Here is the link...

http://www.ebay.com/itm/300937846421?_trksid=p2059210.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT

He had the best price.� Napa carries them, but they don't seem to have them on the shelf.


Tim

Title: Re: Clutch Pedal Link
Post by: 1955CJ-5 on May 28, 2014, 02:15:51 PM
Thanks Tim....are you going to have to drill out the clutch tube and crossover tube to accept the clevis pins?  That might complicate things when the tub is on.....

I couldn't find the ebay items so I ordered from McMaster Carr..zinc plated....

http://www.mcmaster.com/#rod-ends/=s5xd51

Title: Re: Clutch Pedal Link
Post by: johnrb3b on May 28, 2014, 02:48:27 PM
OK that's even better.
McMaster-Carr is just around the corner from my house.
Thanks.
Title: Re: Clutch Pedal Link
Post by: athawk11 on May 28, 2014, 11:02:09 PM
Randy,
The new links are installed.� I didn't have to drill out the tubes.� The holes are 5/16" so the 5/16" clevis pins worked perfectly.

I've driven both ODie and Whitey with the new links.� Everything is working as it should.

 8-)

Tim
Title: Re: Clutch Pedal Link
Post by: 1955CJ-5 on May 28, 2014, 11:16:01 PM
Tim,

Excellent...I'll get mine made and installed soon...

Thanks for bringing this up..I had no idea it was a weak point....

Randy
Title: Re: Clutch Pedal Link
Post by: bretto on May 29, 2014, 08:20:19 AM
Ace hardware has them.
Title: Re: Clutch Pedal Link
Post by: 1955CJ-5 on May 30, 2014, 08:45:24 PM
The clevis ends arrived today...

Tim,

If it's not too late could you measure the 5/16" rod you used and did you think it was too short, too long, or just right?

Thanks,

Randy
Title: Re: Clutch Pedal Link
Post by: athawk11 on May 30, 2014, 09:04:14 PM
I made mine 8 1/4".  I wanted some adjustment, and as much thread as possible making contact between the clevis and the rod. 

I think 8" would be perfect.

Tim
Title: Re: Clutch Pedal Link
Post by: 1955CJ-5 on May 30, 2014, 09:25:29 PM
Thanks Tim,

8" it is......
Title: Re: Clutch Pedal Link
Post by: Ryan_M on May 30, 2014, 09:46:43 PM
I really need to do this. I've broken 2 stock clutch pedal links and now carry an extra with me. Since Tim has posted the exact specs and materials list I'm running out of excuses.
Title: Re: Clutch Pedal Link
Post by: 1955CJ-5 on May 30, 2014, 10:03:06 PM
I think they will take more time to install than it will to get them assembled....

If you were totally clever you would thread one end left hand and the other right hand, and then you could adjust it by simply turning the rod....

But I don't have the right tools to do that......
Title: Re: Clutch Pedal Link
Post by: athawk11 on May 30, 2014, 10:11:46 PM
Quote
I think they will take more time to install than it will to get them assembled....

If you were totally clever you would thread one end left hand and the other right hand, and then you could adjust it by simply turning the rod....

But I don't have the right tools to do that......


That would be a good upgrade to this upgrade.� I suppose there are left hand thread dies out there somewhere.

Tim
Title: Re: Clutch Pedal Link
Post by: athawk11 on May 30, 2014, 10:15:13 PM
Ryan,  did you break one on that crazy Northeast Willys trail run last year?  You guys were tearing it up on that trip.

Tim
Title: Re: Clutch Pedal Link
Post by: 1955CJ-5 on May 30, 2014, 10:22:04 PM
Quote
Quote
I think they will take more time to install than it will to get them assembled....

If you were totally clever you would thread one end left hand and the other right hand, and then you could adjust it by simply turning the rod....

But I don't have the right tools to do that......


That would be a good upgrade to this upgrade.� I suppose there are left hand thread dies out there somewhere.

Tim

The clevis with a left hand thread might be tricky, but I bet they are out there somewhere.....

Mine will have right handed threads and will do just fine... :)
Title: Re: Clutch Pedal Link
Post by: Jesse on June 01, 2014, 11:41:30 AM
This is a great idea, thanks for posting it!



As an aside, I once broke this link on the road. Found a peice of chain in the ditch and used some wire to affix it to the holes. Worked better than walking.


-Jesse
Title: Re: Clutch Pedal Link
Post by: bretto on June 01, 2014, 09:43:27 PM
Quote
Quote
Quote
I think they will take more time to install than it will to get them assembled....

If you were totally clever you would thread one end left hand and the other right hand, and then you could adjust it by simply turning the rod....

But I don't have the right tools to do that......


That would be a good upgrade to this upgrade.� I suppose there are left hand thread dies out there somewhere.

Tim

The clevis with a left hand thread might be tricky, but I bet they are out there somewhere.....

Mine will have right handed threads and will do just fine... :)
Maybe you could find a turnbuckle with wide enough material in the middle for the hole for the pin then cut it in half for two clevises.  Then you could have your left handed thread clevis.  Sounds like too much work though.
Title: Re: Clutch Pedal Link
Post by: johnrb3b on June 02, 2014, 01:21:29 PM
Quote
If you were totally clever you would thread one end left hand and the other right hand, and then you could adjust it by simply turning the rod.
That was the first thing I looked for in the McMaster-Carr catalog. They do have reverse thread clevises and they have rod threaded left and right on opposite ends, but not in the sizes and styles I needed. So I'll just make do with standard thread. It's not like you'll have to mess with this adjustment very often.
Title: Re: Clutch Pedal Link
Post by: athawk11 on June 02, 2014, 02:07:54 PM
John is right. Once adjusted to size, you'll rarely need to adjust the length again.

This brings up another tech question.� From extreme end to extreme end, my original style links measured 10 3/4" on both of my 3As, so this is where I set my new links.� On test runs, this length works fine, but I'm not sure it's correct.

What measurement have others found theirs to be?

I wouldn't ask if your link is installed, as it would be a pain in the rump, but this will be an easy measurement for those of you that have replaced your link.

Tim�
Title: Re: Clutch Pedal Link
Post by: Ryan_M on June 02, 2014, 09:58:25 PM
I broke the first one on my rolling chassis test run but in fairness to the link the pedal was likely way out of adjustment and since there was no tub the pedal traveled further than it ordinariy should have / would have.

I broke a second one on an old 2A I was trying to get started for a friend. I jumped in, mashed the clutch, and SNAP! That's the one that made me realize just how prone to failure these rods can be. I ordered an extra and it lives in the on-board toolbox.

Here are the measurements from the trusty Walck's spare:

10-3/4" outside end to outside end
10-1/2" center of cotter pin hole to center of cotter pin hole

The picture is deceiving as it appears the rod is not properly aligned with the ruler but I can assure you it is.



Title: Re: Clutch Pedal Link
Post by: athawk11 on June 02, 2014, 10:56:29 PM
Excellent!  That confirms it.  Thanks Ryan.

Tim
Title: Re: Clutch Pedal Link
Post by: Birddog7 on June 04, 2014, 09:57:05 AM
Thanks guys for posting this info. Getting the 3A (Stryker) ready for the FCT and its up on jack stands. So it would be a good time to change it out.