My Willys 3A and 3B Community
3A, 3B, DJ Technical Knowledge Base => "Original"-- Technical Questions, Answers, Observations => Topic started by: macrisel on March 19, 2014, 11:14:03 PM
-
Does anyone have the dimensions for the shaft on the distributer and the length of the key on the end?� I'm still having issues with my timing and I think I may have found an issue.� Below are pics and dimensions of my distributer.� When it is completely installed, I can still turn the rotor by hand....
(http://i785.photobucket.com/albums/yy138/macrisel/377E146B-D65C-427C-AB9C-6195E6F06653_zpscmxubagn.jpg)
(http://i785.photobucket.com/albums/yy138/macrisel/7D4E0AEE-094F-4C48-A678-5D2C4BFC6E2E_zpskwq6gerx.jpg)
(http://i785.photobucket.com/albums/yy138/macrisel/4B2F24B5-B899-427F-906C-7B70F0AFA40A_zps3dp9ara8.jpg)
Every time I timed the engine and got it started, the timing would jump around some.� When I revved the motor the timing went to h*ll and the motor died.� The funny thing is, all of this came on all of a sudden.� I moved the jeep one day, let it sit for two weeks and then it wouldn't start.....
Why can a jeep never stay fixed for very long?
-
I'm going to assume that the last was a retorical question.......? It is a Jeep!
;D
Zeke
-
I took some measurements on my distributor and they're pretty much the same as yours.
A couple things:
Yours is missing the little collar down near the tab that fits into the oil pump. Not sure how critical this piece is or if maybe you removed it before you took your pics. That may be your culprit.
Also, if you look close you'll see the tab that fits into the distributor is NOT centered on the end of the shaft. It is slightly off-center. That means it only fits into the oil pump one way. If you have it rotated 180 degrees or anywhere but the correct orientation it won't seat properly (but it will start and run horribly! trust me!). Once seated correctly, you should not be able to turn the rotor by hand.
Once the distributor is installed you want to make sure you have the clamp that locks the distributor to the motor. I've seen those damaged or missing as well.
(http://i1188.photobucket.com/albums/z403/rmurdock2121/51%20Willys%20Jeep%20CJ3A%20Rehab/DSCN2466_zps7f17b655.jpg)
(http://i1188.photobucket.com/albums/z403/rmurdock2121/51%20Willys%20Jeep%20CJ3A%20Rehab/DSCN2467_zpsbb740960.jpg)
(http://i1188.photobucket.com/albums/z403/rmurdock2121/51%20Willys%20Jeep%20CJ3A%20Rehab/DSCN2471_zps7e0d5998.jpg)
(http://i1188.photobucket.com/albums/z403/rmurdock2121/51%20Willys%20Jeep%20CJ3A%20Rehab/DSCN2468_zps481fa5fa.jpg)
-
Thanks Ryan. I took the little collar off before I took the photo. Like you, I'm not sure how critical that ring is, but I'm not going to just throw it away. All the times I had the distributer in and out I took care to make sure I was lining up the offset key with the oil pump. I just could never get it to engage. I've had the distributer out in the past and never had any issues with getting it back in and lined up.
I also thought my clamp may be keeping me from seating properly....so I took it completely off to try and seat the key into the oil pump and could still not get it to lock down in place.
Is there any way the gear on the oil pump could have slid down? I am still getting oil pressure when the engine does start so I don't think the gear has slid off of the camshaft. Also, when I use the GEICO method to time the motor, the flywheeel timing marks and front timing marks line up as they are supposed to on TDC.
The motor ran fine until I parked it!!! >:( Something had to have changed all of a sudden....
I swear..........I'm about two skinned knuckles from switching this thing over to 12 volt with electronic ignition.....
-
I swear..........I'm about two skinned knuckles from switching this thing over to 12 volt with electronic ignition.....
Don't do it! We'll get you back on track here.
When you install the distributor, does it go all the way into the hole in the block and seat as far down as it should or does the distributor housing stick up a little like it would if the tab was not seated in the oil pump? I hope that question makes sense.
If it does go in all the way, maybe you can measure the distance from the opening in the block to the slot in the oil pump using a thin stick (perhaps the oil dipstick?) and see if the measurement is the same as the length of the distributor shaft? That should tell you if anything changed within the oil pump itself. I've never had one apart so I don't even know if it's possible for those gears to move. Someone else will have to chime in. Athawk likes to reindex his pumps if they are out-of-whack so he'll probably know that answer.
Also, if you shine a light down the hole you should be able to see the slot in the oil pump. Perhaps something fell down in there and is obstructing the slot? A long shot but certainly a possibility.
-
I swear..........I'm about two skinned knuckles from switching this thing over to 12 volt with electronic ignition.....
When you install the distributor, does it go all the way into the hole in the block and seat as far down as it should or does the distributor housing stick up a little like it would if the tab was not seated in the oil pump? I hope that question makes sense.
Yes, the dist does seem to bottom out on the block...even after taking the clamp off to give it another 1/8" or so.
If it does go in all the way, maybe you can measure the distance from the opening in the block to the slot in the oil pump using a thin stick (perhaps the oil dipstick?) and see if the measurement is the same as the length of the distributor shaft? That should tell you if anything changed within the oil pump itself. I've never had one apart so I don't even know if it's possible for those gears to move. Someone else will have to chime in. Athawk likes to reindex his pumps if they are out-of-whack so he'll probably know that answer.
Last night, I stuck a long screwdriver down into the the slot to ensure the oil pump was not freewheeling and still engaged to the camshaft.� It was.� I also took a "rough" measurement to see if the dist shaft length and the depth were the same.� I was running out of shop time and didn't get an exact measurement, but it seemed the depth was approximately 1/8" deeper than the shaft length.� That is what spurred my original question regarding the shaft length.
Also, if you shine a light down the hole you should be able to see the slot in the oil pump. Perhaps something fell down in there and is obstructing the slot? A long shot but certainly a possibility.
I saw the slot last night and it didn't appear anything was in there. There also wasn't anything that seemed to keep the screwdriver from engaging the slot.� However, I'll double check tonight when I get an exact measurement on the depth to the oil pump.
Thanks for the ideas!
-
Mac,
There really is no way for the oil pump gear to slide down and off the distributor pin, but I believe there is a roll pin that locks the oil pump gear to the oil pump shaft.� If that pin is sheared it would most surely cause your timing issue, but I don't think you would have any oil pressure.
There is less of a chance for this, but the oil pump could be missing some teeth.� Because of the design, I believe you would need to be missing at least two teeth.� You could remove the valve cover to check the teeth on the pump.
Are the innards below the points, on the inside of the distributor all tight? Or maybe a broken spring?
Tim
P.S. Come On Ryan! I don't like to index these things...I just have no choice! :D
-
If you hold the rotor, can you turn the flat indexing tab at the end of the shaft? I don't know what holds that tab in there but it might be loose enough to turn under pressure...
Also there is a screw in the top of the the distributor shaft where the rotor slips on..is it there and is it tight?
The mechanical advance will allow some movement....does it return when released?
Springs in place?
-
If you hold the rotor, can you turn the flat indexing tab at the end of the shaft? I don't know what holds that tab in there but it might be loose enough to turn under pressure...
Also there is a screw in the top of the the distributor shaft where the rotor slips on..is it there and is it tight?
The mechanical advance will allow some movement....does it return when released?
Springs in place?
When I hold the tab and try to turn the rotor, I get no movement. I think that indexing tab is either pressed on or cast as part of the shaft. I'll check for the screw this evening when I get back in the shop along with the mechanical advance.
-
I just went out and checked, with the distributor firmly installed, I removed the cap and I can move my rotor through about 15 degrees of rotation, but then the springs return it to the starting point.....maybe your mechanical advance is sticking?
Here it is with the advance mechanism removed..
Now I'm thinking there is a clip in there to hold the advance mechanism/cam on instead of a screw...
-
Well, I checked out several things last night and now I have MORE things to check out this weekend.
1. First off, I did get the distributer lined up and fitted down into the oil pump. It was not as easy as it was in the past, and I had to REEEEAAALLY work to get it exactly lined up and then worked into the groove. I have no idea why.
2. With the rotor installed, I can not rotate the rotor either direction. So now I think I need to check my mechanical advance.....
3. I also noticed I have some play (in and out) in my dist shaft. I can't recall if there is any side-to-side movement. From what I'm told.....this is bad also. Does anyone know of a good supplier for new bushings or how hard they are to replace?
4. On top of everything else, when I really got to looking inside my cap, I found my button was missing! The spring was there, but no button! Where did it go? How long has it been gone? How did it even come off?!?!? I have no idea.
5. Finally, to add to everything else and cap off the night I found out my accelator pump on my carb is froze up. ::) This will be the second time in three years I have replaced this pump because it siezes up. Really thinking I may be buying a new carb from Walcks or send my to scoutpilot to professionally rebuilt.....
It was at this point I calmly set my tools down, washed my hands, turned off the lights and headed into the house to play with my girls. Bubble Guppies and SpongeBob suddenly didn't look so bad......
-
Does anyone know of a good supplier for new bushings or how hard they are to replace?
I get the bushings at Tractor Supply, they are just regular bushings. No more difficult to change than any other part on these old Jeeps ;D
-
Thanks Bob! I really needed a laugh right now!
-
I've lost those distributor buttons before....I'd don't think they will run without it as that's how electrical contact is made between the coil and the rotor...I think they are carbon ...
-
Hang in there Mac! Don't jump !!!
1. The distributor is fussy to insert into the oil pump, it was on mine as well, I think your OK there.
2. Bushings may not be so hard, lots of help here.
3. Yup them caps can drop a button, check to make sure you have the right cap, I dropped a button and old 3x just kept running, but she did have some bad habits.� Got the right cap and she started behaving again.� Funny old girl!
4. Carb, yup Scout pilot, no question
5. Bubble guppies and Sponge Bob, yeh I get that too� ;D
-
If you take the distributor apart do it slowly and take pictures! this little whisker spring is in there....just to hold a little tension but watch for it!
-
I've not used these fellows but it would be a temptation....
http://willysdistributors.com/id2.html
-
So I worked on things this weekend and found a few things out.
1. I took apart and cleaned my carb and the accelerator pump seems to be working now. Things were pretty gummed up and the linkages and springs were sticking.
2........I took my distributer apart and checked my advance and everything seemed to be working as it should. However, when I put everything back together and installed the distributer back on the jeep.........I am getting no fire to my plugs. The "gasket" between the breaker plate and the distributer housing was pretty dry rotted. There was also a felt bushing around the screw that comes out of the distributer and connects to the coil wire that was pretty rotted. Since I didn't have anything on hand, I reused them. Now, I'm beginning to wonder if that is my problem. Can I use cork to reproduce these gaskets or should I try to hunt down replacement?
When I touch a test light to the coil wire on the distributer (with the ignition on) I get nothing. Moving back to the coil, I get current on the key side of the coil but not on the distributer side....until I unhook the distributer wire. This leads me to believe the distributer has a short in it somewhere........right? Where else can I look for a short?
Randy, thanks for the link! They look like they really go through the distributer and bring it up to snuff. If I go that route, I am really tempted to update to 12 volt and electronic ignition..... I would like to stay original, but my ignorance of old school is really starting to show....
From what I understand, 12 volt is a little bit more forgiving of problems and that is what the vast majority of my experience is in. I know there is nothing "wrong" with a 6 volt system, but there might be more "right" with a 12 volt.
Thanks for the help guys.. :(
-
There should not be a gasket between the breaker plate and the distributor plate. They should be metal to metal. You will have to replace the insulators in the distributor body where the screw goes through the body to connect the wires to. It is probably shorting out there.
-
It sounds like you have a short all right. Do you have a meter with a continuity function? You can hook it up and wiggle things around and see if there is a short....
There have been a couple of fellows over at the CJ-2a page that have had the electronic ignitions quit working. The thing about points, is they will typically keep working even though the engine may run poorly...when the electronic ignition quits, your done..
Did you replace the little carbon button or use a new cap?
You could probably use a piece of heat-shrink tubing to insulate that stud that goes through the distributor side, along with gasket/cork material on each end....It sounds like maybe the original insulator had already been replaced....
-
When I touch a test light to the coil wire on the distributer (with the ignition on) I get nothing. Moving back to the coil, I get current on the key side of the coil but not on the distributer side....until I unhook the distributer wire. This leads me to believe the distributer has a short in it somewhere........right? Where else can I look for a short?
I agree with the posts above, sounds like you have an unwanted ground. Just keep in mind that when the points are closed the test light will not light up on the distributor side of the coil, only when the points are open. Try testing while cranking the engine, the light should flash as the points open and close.
-
Carl, I may have misspoke but there is not a gasket between the breaker plate and distributer plate..but there is one between the breaker plate and the case of the distributer that was pretty rotten.
Randy, I do have a continuity tester I'll hook up tonight. I ran out of shop time yesterday. The heat shrink tubing is a good idea and I'll probably use it along with the cork/rubber gaskets. Instead of messing with the carbon button, I just replaced the entire cap.
Bob, I will definatly make sure I rotate the motor while I'm checking for current. Right now, the disty is pulled back out and disassembled on my workbench while I wonder what went wrong. It is my luck nothing was broke until I fixed it..........
Does anyone have a photo of the original insulators I could copy from?
-
Oh, one more thing. On looking at the link that Randy posted I noticed my distributer does not have a dust cover inside. Will this really affect anything?
-
[size=12]I venture to say half the distributors out there don't have dust covers. They are another layer of protection from dirt, water, fuel and oil.[/size][/b]
-
Mark, try these people for parts for your distributor. http://willysdistributors.com/ I got it from the G503 site.
-
I finally managed to get back out into the shop last night and work on my distributer. I took great pains to make gaskets to insulate the breaker plate assembly from the distributer housing and used heat shrink tubing to insulate the machine screw where the coil wire hooks up. I even went so far as to make a gasket to fit on the outside of the distributer over the same screw to (hopefully) keep out some moisture.
After all of that, I took a Dremel with a small wire wheel cleaned up all the contact points to make sure I would get a solid contact on everything. Finally, I took my meter and checked for continuity and verified I didn't have anything grounding out where it shouldn't be. To the best of my knowledge, everything appeared to be working as it should....
I then decided to go the extra mile and put the distributer back in the jeep and give it a go. I made extra sure to get the disty seated into the oil pump and even used a rubber mallet to make sure it was completly bottomed out. I brought the motor up to TDC, lined up the rotor button and the cap, strapped everything down, pumped the gas twice, kicked the starter.............and the motor hit once, fluttered and died. One more pump on the gas, kick the starter and the motor hit and took off and started running! I almost jumped out the seat I was so happy! I pumped the gas and everything revved up all the way as it should. What a relief..
I didn't get to take it for a drive due to the monsoon that was going on last night. I'm hoping this evening or this weekend to take it out and put it through its paces. It still seems it is running rich, but no more than it was before all this was started two weeks ago.
Fingers crossed!!
-
Hooray!
-
Sweet!!! 12V conversion be damned!!
-
Sweet!!! 12V conversion be damned!!
Whoa, whoa, whoa....lets not get ahead of ourselves Ryan.. :-?
By the way, if anyone is interested I contacted Willys Distributers (the link Carl and Randy posted) about rebuilding my distributer and they were very polite and seemed very experienced on these ditributers. However.....due to demands from his day job he stated his current turnaround time was 3-4 months on rebuilds.
-
12 volt...Really?
After all that trouble you went through to repair your generator mount?
It seems to me that the resistor keeps the ignition at 6v anyway, but the starter will crank faster!
-
Mine is converted to 12 volt, I like it as I can use some of the modern accessories easier, ie winches and lights. I used a coil with an internal resistor, this drops the voltage to 8 volts. Make sure you change your head lights as well, and yes it does make the starter really whirr! I've had this conversion for about 3 years now and have not had a problem with the starter burning out.
-
My Jeep is 12v also and I have no starter problems. If your planning to use a winch and other high amp draw equipment get the highest amp alt. you can. I have a 60A alt and it helps with the winch use.
-
Well.........I'll keep it 6 volt for now. I took great pains in trying to keep this jeep original so I'll fly that course for now. Maybe sometime in the future I'll switch it over to 12 volt if I change how I use the jeep. I'm not planning on adding any modern accessories (radio, winch, lights) right now so I should be okay. In addition, I've already bought a 6 volt battery tender and I would hate for that to go to waste.
However..........for my next Willys project sitting in the shed I can make no promises about keeping it original..... ;)
-
On a side note, I really appreciate all the help everyone gave me on this. It took a while to figure it out and I was scratching my head several times.
Everytime I open the hood on the jeep for something, it seems is isn't long before I'm also opening the laptop and pulling up this forum.
Thanks again to a great bunch of guys.