My Willys 3A and 3B Community

3A, 3B, DJ Technical Knowledge Base => "Original"-- Technical Questions, Answers, Observations => Topic started by: 1955CJ-5 on February 01, 2013, 07:25:50 PM

Title: Hood Latches/hold downs
Post by: 1955CJ-5 on February 01, 2013, 07:25:50 PM
Why do some 3A's have two hold downs and some have four?

 Are the extra two in the rear added somewhere along the way by the owner's?

Mine has two but it would sure benefit  from four...

Randy
Title: Re: Hood Latches/hold downs
Post by: garage gnome on February 01, 2013, 07:33:11 PM
People add the two rear ones to keep the hood vibration down. I've never needed them on mine.
Title: Re: Hood Latches/hold downs
Post by: 1955CJ-5 on February 01, 2013, 07:37:10 PM
Well, mine doesn't run yet so I don't know if it will vibrate...but it would improve the "fit and finish" �.....!
Title: Re: Hood Latches/hold downs
Post by: F Bill on February 01, 2013, 07:51:01 PM
It is a pretty common period mod so I don't think anyone will give you a hard time.. Do your underhood reenforcements look solid or are they breaking spot welds? Normally the one piece brace at the back of the 3A style hood does a good job holding the hood together, unlike the earlier multipiece ones..
Title: Re: Hood Latches/hold downs
Post by: 1955CJ-5 on February 01, 2013, 10:09:11 PM
The hood is in good shape and the rear one piece brace looks fine. It's just that when the front is latched the back part of the hood still has a pretty good gap to the fender. I'll work on it...now that i know the latches are owner-added...
Title: Re: Hood Latches/hold downs
Post by: Gunslinger on February 02, 2013, 10:06:22 AM
Quote
The hood is in good shape and the rear one piece brace looks fine. It's just that when the front is latched the back part of the hood still has a pretty good gap to the fender. I'll work on it...now that i know the latches are owner-added...

I would throw out a caution flag at this point.  I just need some clarification.  You say that when the front is latched, there is a pretty good gap at the back.  I'm not sure that putting more latches on will solve that.  The gap between the hood and fender should be a constant 3/8 - 1/2 inch all along the fender, if it varies front to back its most likely that your fenders are not on straight, I would start there and make sure that they are straight.

Next question is what problem are we solving for now?  Is the hood flapping, rubbing, or is there a deep vibration sound at a specific idle.  I thought I needed a second set of latches, after I fixed the fenders I found that the hood didn't make noise anymore and the  rubbing went away. I did have a deep vibration sound that turned out to be the baffle in the fuel tank, vibrations at a harmonic, I added some isolators to move the tank off of the floor and that went away as we'll.

If you need a nice set of stainless steel polished hood latches let me know, I have a set to sell.
Todd


Title: Re: Hood Latches/hold downs
Post by: 1955CJ-5 on February 02, 2013, 11:56:32 AM
Well, we really aren't solving any problem yet. My first post was just looking for info on whether or not the second set of latches was factory or owner installed.  I've seen many pictures with either combination of latches...Motors out, and the fuel tank is out..

Thanks for the info though. No telling what I may come across as I progress

I can nearly reach down and tie my shoes through the hole that was under the fuel tank....

Latches will come later....

Randy
Title: Re: Hood Latches/hold downs
Post by: 1955CJ-5 on February 02, 2013, 12:06:45 PM
 I went out and latched the hood and measured the gap. It is very consistent at just under 1/2"...

I guess the gap I was looking at was between the curved part of the hood and cowl. but if that were pulled down then the hood to fender gap would be off. �

I'll leave it as is for now..

Randy
Title: Re: Hood Latches/hold downs
Post by: Macgraham on February 02, 2013, 07:10:41 PM
You'd be surprised how much heat that gap will help to get rid of on a hot summer day. Could help with the engine temp. Just a thought.
Title: Re: Hood Latches/hold downs
Post by: 1955CJ-5 on February 02, 2013, 07:43:24 PM
That had crossed my mind....I was reading somewhere about radiator shrouds and someone mentioned that the L-head was sort of prone to overheating on warm days....any little bit of ventilation would help.
Title: Re: Hood Latches/hold downs
Post by: johnrb3b on February 04, 2013, 09:57:33 AM
A few guys on the 3B forum have added a second set of latches for this reason.
They re-powered with a V6 or V8 and started driving above 65 MPH. At those speeds the hood starts lifting against the springs in the latches. One guy's hood lifted (at well above 70 mph!) and stretched the springs out to about 2 feet long. Yikes! He of course replaced his original latches and added a second set as well.

If you stay with stock engine and brakes, you'll only need to worry about hood lift if you're driving flat out into a strong head wind. I did that once, bucking a 20+ mph wind. In overdrive I couldn't hold any speed above 45 mph. But the hood was bouncing in the combined 60+ mph airstream.
Title: Re: Hood Latches/hold downs
Post by: Ryan_M on February 06, 2013, 05:38:07 AM
Speaking of hoods, after 11 months, I finally got mine back this week. I can't say that I'm real happy with the fit. I guess this is what happens when the hood is being repaired and reshaped while the rest of the Willys is 40 miles away. I'm not sure there is much I can do with it except keep my eyes open for a replacement. My hood was pretty rough when I first got the Jeep. It has now been beaten, braced, and bondo'd every way possible and this is how it turned out. The gap between the edge of the hood and the top of the fenders is a pretty consistent 1". �I think the problem lies in the hood but is there any way to tell for sure if it's the fenders and tub that are off instead? I'd hate to reconfigure or replace this hood only to have the new version look exactly the same.

(http://i1188.photobucket.com/albums/z403/rmurdock2121/51%20Willys%20Jeep%20CJ3A%20Rehab/DSCN1870_zps10df3ff9.jpg)
(http://i1188.photobucket.com/albums/z403/rmurdock2121/51%20Willys%20Jeep%20CJ3A%20Rehab/DSCN1877_zpsdbac53ca.jpg)
(http://i1188.photobucket.com/albums/z403/rmurdock2121/51%20Willys%20Jeep%20CJ3A%20Rehab/DSCN1879_zpsa6d99c80.jpg)
(http://i1188.photobucket.com/albums/z403/rmurdock2121/51%20Willys%20Jeep%20CJ3A%20Rehab/DSCN1880_zps4a67df60.jpg)
Title: Re: Hood Latches/hold downs
Post by: Jeff_M on February 06, 2013, 08:05:36 AM
Could be worse, I suppose. �At least it fits flush on the front. �It is disappointing, however, when you look at your early pre-refurb photos and see how much better it fit. �If someone says something, you can tell them you had to lift the hood to make room for the turbo kit. � ;)
Title: Re: Hood Latches/hold downs
Post by: F Bill on February 06, 2013, 09:12:17 AM
Ryan, Look at the hinge area of the hood and the cowl where the hinge bolts on. Something there is not right. You shouldn't be able to see under the back of the hood. It almost looks like the hood is also too far back. If you can get a picture of the cowl, with the hood removed we might be able to see something there.

I would try some spacers behind the hinge and attempt to slide the hinge downward as much as possible. Hopefully it is not a new hinge welded on incorrectly or a damaged cowl.

You may be able to raise the fenders some to close the gap somewhat.

You are right, it would be  ashame to mess up that nice bodywork to get the gaps right.. It would be worth puttng a few layers of masking tap on the edges and fender tops while you get it right, just don't leave it on so long it dries out and gets impossible to remove.
Title: Re: Hood Latches/hold downs
Post by: Ryan_M on February 06, 2013, 09:48:49 AM
Here's a couple pics sans hood. Do you see anything there that looks wrong? I'll take a closer look at my "Before" pics when I get home but I think the area where the hood hinge bolts to the cowl looks the same as it always did. I have the original rain gutter installed as well. The hinge is down as low as it will go as I had the hood opened straight up before tightening the hinge bolts (see third pic here). I'll have to see if the bottom edge of the hinge can be ground down at all to provide a tighter fit. I forget now if the hinge is original or modified during the body work.


(http://i1188.photobucket.com/albums/z403/rmurdock2121/51%20Willys%20Jeep%20CJ3A%20Rehab/164d562a-bc6e-4ebf-b153-85bb2312f9c1_zpsf885c667.jpg)
(http://i1188.photobucket.com/albums/z403/rmurdock2121/51%20Willys%20Jeep%20CJ3A%20Rehab/DSCN1601.jpg)
(http://i1188.photobucket.com/albums/z403/rmurdock2121/51%20Willys%20Jeep%20CJ3A%20Rehab/DSCN1864_zps448a0265.jpg)
Title: Re: Hood Latches/hold downs
Post by: garage gnome on February 06, 2013, 10:08:20 AM
Mine has about the same gap on the back.
Title: Re: Hood Latches/hold downs
Post by: F Bill on February 06, 2013, 10:51:47 AM
It looks right, but in your installed picture the hood looks too high.  Try it without the rain gutter and see what happens. Did you do any welding or repair to the hinge??
Title: Re: Hood Latches/hold downs
Post by: bretto on February 06, 2013, 12:45:34 PM
Is there any give in the fender adjustment height or can the grill be lowered?
Title: Re: Hood Latches/hold downs
Post by: Gunslinger on February 06, 2013, 05:06:30 PM
Ryan,
You have a beautiful jeep there, I think I would be tempted to put the hood back on as good as you can.  And then I would take the whole jeep over to the guy who did the work and politely ask him if he could help you get the hood aligned/installed correctly.  With a masterpiece like that, he is going to want to show off his work with pride, not have someone say " nice jeep, what happened to the hood".  I'm going to guess he will work extra hard to make sure that his name is properly reflected in the hood fit up.  
My 2 centavos
Title: Re: Hood Latches/hold downs
Post by: Ryan_M on February 06, 2013, 07:49:01 PM
So tonight I removed the hood and re-installed it with and without the rain gutter. There is no give to the fender play and the grill cannot be adjusted. None of the bubba-added support braces are hitting anything on the engine. There is one support that is costing me an 1/8" where the hood hits the top of the grill but even if that wasn't there the hood would still have issues. �I'm pretty confident at this point that the hood is simply misshapen. It's been beaten and bubbified to an extent that it just isn't right. I was able to close up the gaps by about 1/4" but it's still obviously screwed up. I'm going to talk to the guy that did the work but I don't expect he'll be able to do much more.

On the bright side, at least for now I won't have to worry about overheating due to lack of airflow through the engine bay �:-/

And 1955CJ-5 - sorry for completely hi-jacking the thread.
Title: Re: Hood Latches/hold downs
Post by: 1955CJ-5 on February 06, 2013, 08:01:33 PM
Quote

And 1955CJ-5 - sorry for completely hi-jacking the thread.

Oh no trouble at all..my question was answered long ago and I learned plenty from all the other questions ...and I got to look at that really nice jeep of yours...!

Randy
Title: Re: Hood Latches/hold downs
Post by: Ryan_M on December 19, 2013, 01:04:59 PM
I hijacked this thread 10 months ago so I might as well ride it out. Look what showed up yesterday! Initial fit is a tremendous improvement over the original hood. I can actually pull and hook each latch one handed and without having to throw my weight on top of the hood to bend it down.

Soo....now I just have to learn how to prep and paint. How hard can that be? It only has to match the rest of Jeep color and finish precisely..

(http://i1188.photobucket.com/albums/z403/rmurdock2121/51%20Willys%20Jeep%20CJ3A%20Rehab/20131218_191417_zpsd69f91fd.jpg)

(http://i1188.photobucket.com/albums/z403/rmurdock2121/51%20Willys%20Jeep%20CJ3A%20Rehab/20131218_191432_zpsc383b191.jpg)
Title: Re: Hood Latches/hold downs
Post by: 1955CJ-5 on December 19, 2013, 02:28:57 PM
Just keep in mind that it's all about preparation...

Paint hides nothing, in fact it helps to bring out the imperfections so that you can see them ever so clearly!

Nice fit on the new hood...where it the rest of the jeep, out back?
Title: Re: Hood Latches/hold downs
Post by: 1955CJ-5 on December 19, 2013, 02:31:25 PM
Hey, as long as this is a free-for-all thread....how about a close up of your under seat fire extinguisher arrangement...I think I like it!
Title: Re: Hood Latches/hold downs
Post by: Ryan_M on December 19, 2013, 04:53:25 PM
Here's a few pics of my extinguisher set up. I have two leg straps that I scavenged from a Gerber knife sheath. They are far from authentic looking but the buckles are big enough that I think I could easily release them even in the fumbling panic of a fire. I ran them through the gas tank strap and cinched the adjustment tight around the extinguisher. The extinguisher is out of the way but easily accessible at all times. It was intended as a temporary arrangement but it's been there for a year now, as evidenced by the rust thriving beneath it...
Title: Re: Hood Latches/hold downs
Post by: 1955CJ-5 on December 19, 2013, 09:27:52 PM
Panic?

I've thought briefly about how I'd go about fighting an engine fire....

I expect that by the time you realized you had a fire, shut the thing down, stopped and got out with the extinguisher, the hood would be too hot to open....besides, you probably would not want to introduce that nice draft in there and fan the fire.

It probably would not be effective to try and shoot through the radiator..

I thought maybe it would be best to reach under the jeep and shoot the extinguisher up.....or maybe through that 1/2" gap between the hood and fender....

A dry chemical will sure make a mess....co2 would be the way to go but it's expensive.

There was a picture of a burning jeep wagon on ewillys a month or two ago...

The fellow commented that one extinguisher was not enough.....

Quick release is good though...maybe to grab it and run would be the best plan....
Title: Re: Hood Latches/hold downs
Post by: johnrb3b on December 20, 2013, 12:27:36 PM
Yeah that was very sad.
That was Kevin from Georgia. He drove that Wagon from GA to Moab and back a couple years ago.
He was chasing a fuel leak. It caught fire going down his driveway. He ran back to the house for a fire extinguisher so the fire had plenty of time to take hold. By then one extinguisher wasn't enough.
Keep the extinguisher in the vehicle.
Of course, realize that an ABC dry chemical will wreck everything electronic in your vehicle. If you can, use only BC type. In the summer I carry nitrogen and in the winter BC dry chem.
Title: Re: Hood Latches/hold downs
Post by: 1955CJ-5 on December 20, 2013, 01:00:09 PM
Every time I look at that picture it makes me feel sad...what a shame..

I've now been shopping for under-hood extinguishers....most I have found are for marine use, and trigger at 175 degrees F...that might be too low for a jeep engine compartment..but one that could be manually discharged might be an option..

Is it a nitrogen extinguisher?

I have an old Halon that I carry around, but it's pretty old, though it still shows that it is charged..
Title: Re: Hood Latches/hold downs
Post by: johnrb3b on December 24, 2013, 12:34:51 PM
Nitrogen extinguishers can freeze in the winter. It doesn't harm them, they work when thawed. But they're no good while frozen.

The advantage of nitrogen is that it not only chokes the fire (no oxygen) but also dissipates heat reducing the possibility of re-ignition.

Meanwhile, Halon is slowly going away. It's already illegal in many countries. If nitrogen didn't have the freeze problem it would be the best solution for under hood.