My Willys 3A and 3B Community

3A, 3B, DJ Technical Knowledge Base => "Original"-- Technical Questions, Answers, Observations => Topic started by: CJPilot on December 28, 2012, 09:33:36 PM

Title: CJ3A Body kit
Post by: CJPilot on December 28, 2012, 09:33:36 PM
I got a chance to test fit my new tub the other day.

(http://i1146.photobucket.com/albums/o537/CJPilot1/Publiccj3a/20121226_183324.jpg)

(http://i1146.photobucket.com/albums/o537/CJPilot1/Publiccj3a/20121227_105554.jpg)

But WOW �:o � I am surprised at how much work it's going to take to get this looking right. �

I knew when I bought it I'd have to drill the mounting, steering column and other holes, and I knew I'd be messing with the fit up but
there are more things wrong than I had planned on. �I'll get it all to work but it'll take some time. �My goal is a vehicle to use around my property
and I'm sure that will happen. �

I found this link listing the problems some one had over on the 2A page. �It pretty much covers the work needed.

http://www.thecj2apage.com/forums/md-juan-body-faults_topic26386.html


Time for a beer er make that a few..

Steve




Title: Re: CJ3A Body kit
Post by: garage gnome on December 28, 2012, 09:51:48 PM
Build the jeep completely, and I mean completely! That's what I did with mine and it made it look soo much better after paint. That way, you are not afraid to cut/beat/drill/weld on it.
Title: Re: CJ3A Body kit
Post by: F Bill on December 28, 2012, 09:53:14 PM
Steve, if you can document what you have found it will make a great FAQ post. As you do the installation if you can keep track of approximately how much time and what you had to do to fix the tub, and post it here, it will help a LOT of your fellow 3A  people.

Is the primer on your tub e-coat or some junk primer?

A lot of the missing holes listed over at the link were for things that may not be installed on a restomod or modified jeep. Probably better to do youw own on that sort of thing anyhow.

Did they finally get the gage holes correct? Transmission  shifters lining up?

I will be following this one closely!  :)
Title: Re: CJ3A Body kit
Post by: garage gnome on December 28, 2012, 09:54:02 PM
I just looked at your profile, you're in central MA? I'm in Western MA. If you ever want, you are more than welcome to come check out my '53 or my very original '49!
Title: Re: CJ3A Body kit
Post by: garage gnome on December 28, 2012, 09:55:39 PM
Bill, that black primer is junk! I had flakes coming off my tub the size of dollar bills! They spray that stuff right over the oily sheet metal.
Title: Re: CJ3A Body kit
Post by: CJPilot on December 29, 2012, 07:44:09 AM
Bill - �The primer looks OK on the tub and right fender. The passenger fender is more of a glossy finish and doesn�t seem as good. I have not looked at the tail gate or windshield yet. �I have not tried sanding anything so time will tell if this primer is actually adhering to the substrate. � In a previous job I painted equipment, mostly with DuPont Centari and Imron. �I used to use a self etching primer on bare metal. The spot welds have a fair amount of expulsion and I�ve cut myself while running my hand down the side of the Jeep looking for any waves in the panels. � They are not perfect but for an old Jeep, to run around with, I don�t think I�ll be doing and straightening of the panels.

The gauge holes are good (but they would be EZ to fix if needed). �I will be taking a better look at the transmission cut out today.

The emergency brake support behind the Dash Panel is in the way of the foot starter hole (which is missing) �I had to cut the bracket out in order to put the hole in. I�m going to try using my original bracket. I do agree for a resto upgraded Jeep a lot of these things would not be a problem.

GG � I�d like to take a look at you Jeeps� sometime. �The only thing I have to look at for help right now is 2 very rusted examples and a lot of the details are eaten away by salt. Maybe you could PM me with some contact info.


Steve
Title: Re: CJ3A Body kit
Post by: CJPilot on December 29, 2012, 08:01:20 AM
I need some help with locating my gas tank. My original (it came with the Jeep) gas tank doesn�t fit into the new tub right. �It will not lay flat on the floor. It looks like it is being held up out of position by the filler neck hole. �My original tub is so badly rusted I cannot get a good measurement of the location (height) of the filler neck hole.

(http://i1146.photobucket.com/albums/o537/CJPilot1/Publiccj3a/20121228_204609.jpg)


The gas tank hold down location does not appear to be in the proper location as well.

(http://i1146.photobucket.com/albums/o537/CJPilot1/Publiccj3a/20121228_204440.jpg)



Steve
Title: Re: CJ3A Body kit
Post by: athawk11 on December 29, 2012, 05:59:26 PM
Hi Steve,

I measured mine. �Original 1949 3A tub. �Reproduction gas tank from Walcks.

Using a tape measure in your same location, I get 6 1/8" to the lower edge of the flange of the filler neck. �I get 6 3/4" to the top of the flange where it starts to bend. �These measurements don't appear to be too far from yours.

My tank measurement from the wall of the Willys to the center of the bolt head on the hold down is 13 1/16". �The biggest difference I noticed is the distance between the edge of my tank and the wall of the Willys...1 1/8". �It's a little hard to tell, but yours looks like it's a bit over 2". �I can't say that mine is correct, but the repro tank lined up just fine. �

Do you have the anti-squeak material under the tank? �This would raise the tank a little, allow you to move the tank closer to the wall, and center the tank neck in the filler hole opening.

Tim

Title: Re: CJ3A Body kit
Post by: garage gnome on December 29, 2012, 06:08:08 PM
Yes, I was thinking he needs the anti squeak material too.
Title: Re: CJ3A Body kit
Post by: CJPilot on December 29, 2012, 09:20:28 PM
Thank you Tim and GG for the input. �Now that I think about it I guess the best measurement would be from the inside floor to the bottom of the filler neck opening. �My tub is not what you�d consider the same as an original, it seems like everything is off 3/8� to an inch. �I plan on changing the filler opening with my original. �I tried setting my tank on some �� wood, for spacing, �but the filler neck still (just barley) hit the opening. �I kind of think it should be centered in the opening. How thick is the anti-squeak ? �

(http://i1146.photobucket.com/albums/o537/CJPilot1/Publiccj3a/20121229_142404.jpg)
Had to get out my spot weld cutter. I have not used it for all most 25 years. �


Once I figure out were my filler opening should go I'll plug weld it in place.
(http://i1146.photobucket.com/albums/o537/CJPilot1/Publiccj3a/20121229_142919.jpg)

Steve

Title: Re: CJ3A Body kit
Post by: athawk11 on December 29, 2012, 09:46:49 PM
Steve,
The anti sqeak is maybe an 1/8".

I measured mine.  5 3/4" from the floor on the inside the tub to the filler cut out.  This may be a bit off.  I did replace my floor pans.  But again, original tub, a repro tank, anti squeak, and it all aligned just fine.

Could the tank be the problem?  After I replaced my floor pans, there was no more sagging floor.  All the sudden, the original tank filler neck didn't fit right.  I had to cut the neck off and reposition it.  Ultimately, this original tank leaked at the fuel line connection, so I replaced it.

Tim
Title: Re: CJ3A Body kit
Post by: CJPilot on December 29, 2012, 09:51:46 PM
The repo emergency brake support is not made anything like the original. �So I cut both my original one and the new and improved repo one out . �By the way, its not a lot of fun.

(http://i1146.photobucket.com/albums/o537/CJPilot1/Publiccj3a/20121229_112329.jpg)
Repo on the bottom


 I positioned the original bracket in my new tub, drilled the bottom mounting holes and then welded the upper in place. That set up the hole location for the emergency brake cable in the fire wall. �Of course the repo tub hole is not even close, so I drilled a new one. That left me with one extra hole and neither one in the proper location.

(http://i1146.photobucket.com/albums/o537/CJPilot1/Publiccj3a/20121229_174805.jpg)


A couple of plugs
(http://i1146.photobucket.com/albums/o537/CJPilot1/Publiccj3a/20121229_173841.jpg)



Welded in, Ground flush, New hole drilled, Then add some juice
(http://i1146.photobucket.com/albums/o537/CJPilot1/Publiccj3a/20121229_193936.jpg)


This is more like my original tub
(http://i1146.photobucket.com/albums/o537/CJPilot1/Publiccj3a/20121229_200833.jpg)




Steve
Title: Re: CJ3A Body kit
Post by: CJPilot on December 29, 2012, 10:03:43 PM
Tim

Thanks for the measurement. My floor to the bottom of my filler neck opening is 5 �� also. �Tank? �I'll post some dimensions tomorrow.

Steve
Title: Re: CJ3A Body kit
Post by: Bob W on December 30, 2012, 11:14:41 AM
Quote
Tim

Thanks for the measurement. My floor to the bottom of my filler neck opening is 5 �� also. �Tank? �I'll post some dimensions tomorrow.

Steve

Can you post a photo of the front of your fuel tank?
Title: Re: CJ3A Body kit
Post by: athawk11 on December 30, 2012, 02:04:20 PM
Steve,

I saw the photo of your tank over on the 2A page. �The filler tube looks to be positioned substantially lower on your tank than either my original or reproduction tanks.

Your current fabrications are looking terrific. �You appear to know your way around a welder. �I doubt I have to add this caution, but welding an old gas tank can be a very dangerous game. �I did reweld my filler tube on my old tank, but I prepped it for a week prior to building up the courage to weld it. �That was a terrifying 15 minutes. :-[
Tim
Title: Re: CJ3A Body kit
Post by: CJPilot on December 30, 2012, 03:38:50 PM
Bob here is a picture of the front of my tank

(http://i1146.photobucket.com/albums/o537/CJPilot1/Publiccj3a/20121230_135040.jpg)



And a close up of the filler neck

(http://i1146.photobucket.com/albums/o537/CJPilot1/Publiccj3a/20121230_143751.jpg)

Tim I have had some fun welding tanks before. �I watched from a far as the fumes were purged, washed and then flashed. �It all seemed perfectly normal for a kid. �My job was to weld it after it was safe to do so. The fun part was watching as my mentor duck taped a propane torch to a broom handle them reached around a corner and made sure the tank was ok for me to weld. I miss those days and a miss him.

Steve
Title: Re: CJ3A Body kit
Post by: Bob W on December 30, 2012, 03:46:20 PM
That is not an original tank so it's dimensions may not be accurate.
Title: Re: CJ3A Body kit
Post by: CJPilot on December 30, 2012, 04:07:26 PM
Thank you Bob. �I should have guessed. �The tank looked so much better than anything surrounding it. �Now what to do? �Anybody know if a repo gas tank actually fits in a repo tub. �I�d bet a beer it will not. Maybe I can find a good used one.

Time to start on something else.

Steve
Title: Re: CJ3A Body kit
Post by: garage gnome on December 30, 2012, 05:32:16 PM
My new tank fits my new tub just fine.
Title: Re: CJ3A Body kit
Post by: CJPilot on December 30, 2012, 07:21:03 PM
Thanks Nate. �I will include a new tank in tomorrows planned purchases.

Anybody know if the holes for the pedal shafts are round or oval? �My original tub has oval holes but they might have been worn that way. Just want some confirmation before �I cut them out.


Steve
Title: Re: CJ3A Body kit
Post by: Dennisanvil on December 30, 2012, 07:22:03 PM
hi guys
i have welding on differant tanks by put the exhaust from a runnig truck into the opening of the tank , which drive the flume out and then you could weld on it. or you could solder it as the isnt any fire with a solder copper.
dennis
Title: Re: CJ3A Body kit
Post by: F Bill on December 30, 2012, 08:55:27 PM
Just in case anyone is searching in the future and hits this thread I will put the same drawing link in here with the fuel tank opening ..
http://www.thecj2apage.com/forums/need-some-measurements_topic26697_post235211.html?KW=#235211

it is a drawing of an early CJ2A quarter panel showing the opening for the fuel door. (The piece the tank spout goes thru that is spot welded to the quarter panel) �It shows the tool indents for the very early models , don't pay any attention to them. As far as I know the 3A panel should be the same for the fuel opening dimensions. If anyone knows differently please let us know. �:)
Title: Re: CJ3A Body kit
Post by: garage gnome on December 30, 2012, 09:35:32 PM
Quote
Thanks Nate. �I will include a new tank in tomorrows planned purchases.

Anybody know if the holes for the pedal shafts are round or oval? �My original tub has oval holes but they might have been worn that way. Just want some confirmation before �I cut them out.


Steve

They are oval.
Title: Re: CJ3A Body kit
Post by: athawk11 on December 30, 2012, 09:36:43 PM
Steve,
My holes are oval.  They look pretty clean, so I don't think they were worn to this shape.

Thanks to Bill for the Link.  That Jpet does some incredible work.

Tim
Title: Re: CJ3A Body kit
Post by: CJPilot on December 31, 2012, 09:08:23 AM
Oval it is. � I just have to figure out how to make them.

I need to order a new tank. �I have run across two different repo tanks and I�m looking for feed back on which one will fit like an original.

Tank #1 is a omix-ada
(http://i1146.photobucket.com/albums/o537/CJPilot1/Publiccj3a/Bd76LRQBGkKGrHqYH-DgErgdcdisBK7Kv836Q_12_zps7f7248ce.jpg)



Tank#2
(http://i1146.photobucket.com/albums/o537/CJPilot1/Publiccj3a/KGrHqIOKm8E5I-CrzR8BOcNCjyMg60_12_zps55feeb1d.jpg)


Tank#2 no hold down bracket and has a very long and what looks like a out of location filler neck but I don't have an original tank to compare it to.


Steve
Title: Re: CJ3A Body kit
Post by: F Bill on December 31, 2012, 11:03:29 AM
If you have a die grinder with a cylindrical burr on it you can oval out those holes. Before you do that, trace the holes on a piece of cardboard and make sure they are exactly the same, not worn to the shape you see now. I am not entirely convinced the holes were oval originally but don't take my opinion on it. Also, if you have a chassis punch like electricians use you can use it to take a bite out of the existing hole and get it closer to the shape you might want.

As far as tanks go the second one looks strange to me.. Who supplies that one and what is it supposed to fit? I have quite a few original tanks that leak badly, and if I have time today and can find a good one I will see if I can find one that hasn't been patched up to take a pic of. The Omix tank may fit their tub, I do know some have had problems with it fitting a stock tub.
Title: Re: CJ3A Body kit
Post by: athawk11 on December 31, 2012, 01:06:04 PM
Hi Steve.

This is the tank I purchased. �It's not the cheapest option, but the filler neck fit perfectly. �I did have to trim the fuel line and drain holes in my floor pans, as they did not line up quite right. �Not sure if this was the Classic Enterprises floor pans, the Walcks tank, or my positioning of the pans. �None the less, this was an easy fix compared to a mis-aligned filler neck.

http://walcks4wd.com/fuel-tank-cj2a-cj3a-and-early.html

Tim

Title: Re: CJ3A Body kit
Post by: CJPilot on December 31, 2012, 06:04:38 PM
I used Jpets drawing and my repo tub�s filler neck hole is .177� �high �when measured on the outside. �

F Bill, �Tank #2 is being sold on Ebay.

I have ordered the Omix-Ada fuel tank. �At lest I can cut it apart and weld it back together if I have to. And I don�t have to worry about blowing myself up doing it. ;D

Tim, I think the tank Walcks sells is the same tank that everybody else is selling i.e. the Omix-Ada

Steve
Title: Re: CJ3A Body kit
Post by: athawk11 on December 31, 2012, 06:18:44 PM
Steve,
I think you're right. �I just trusted Walcks to not sell me something that wouldn't fit right. �+ I hit the magic $150.00 free shipping mark ;)
Title: Re: CJ3A Body kit
Post by: CJPilot on December 31, 2012, 06:41:09 PM
Tim, �So I am not alone when it comes to hitting the 150 dollar mark? :)   It 's a win win as far as I can see.  Especially when you buy a CJ3A in boxes like me.

Steve
Title: Re: CJ3A Body kit
Post by: CJPilot on December 31, 2012, 10:20:15 PM
I took some measurements of the holes in the tub floor, and drew up my findings.
These are the steering column, gas pedal, dimmer switch and pedal shaft holes. Anybody know of a definitive drawing showing these details?

(http://i1146.photobucket.com/albums/o537/CJPilot1/Publiccj3a/CJ3AFloorHoles_zps4cd2b61f.jpg)

This is my first pass at this and will most likely be updated once I look at everything again.
My steering column hole is already in and will help locate the other holes.

Once I finalize a design I can attempt to cut the holes. �For the pedal shaft holes I think I�ll lay it out, * punch the centers and use a hole saw to start with.
I�ll need to saw two overlapping holes to get the oval shape. I�ll saw most of the way through and move 5/16� �off center and saw that hole which will remove
my center �for the other half so I�ll have to finish it with a carbide bur. The other holes I�ll use a speed bit.



Steve
Title: Re: CJ3A Body kit
Post by: CJPilot on January 01, 2013, 09:38:36 AM
I needed confirmation that my layout was correct. So I printed a section full scale and cut the holes out with scissors. �Next I tried fitting it up with the holes in my original tub

(http://i1146.photobucket.com/albums/o537/CJPilot1/Publiccj3a/20130101_090159.jpg)

Close enough for me. �Now I can try fitting it up in the repo tub.


Steve
Title: Re: CJ3A Body kit
Post by: CJPilot on January 01, 2013, 09:16:04 PM
 My plan worked. I�m glad to have this behind me.

(http://i1146.photobucket.com/albums/o537/CJPilot1/Publiccj3a/20130101_191706.jpg)


(http://i1146.photobucket.com/albums/o537/CJPilot1/Publiccj3a/20130101_194912.jpg)


Steve
Title: Re: CJ3A Body kit
Post by: macrisel on January 01, 2013, 10:34:55 PM
Been there, done that!  Make sure you test fit all your gauges, ignition switch, dimmer switch and everything else that gets a hole.  My repro tub holes were all a little bit too small for everything and I had to massage them out with a die grinder a little.  You may also find that the original fenders fit better than the repro fenders and vice versa.  And the windshield.........and the tailgate.......and the grille.

Like everyone else said, put the whole thing together first to fit everything together.  Don't be suprised by anything......quality control in the Phillipenes is a suggestion at best.

I have already assembled my reproduction body kit, disassembled it and am now getting close to paint.  Don't even get me started on how "straight" the repro body is!
Title: Re: CJ3A Body kit
Post by: CJPilot on January 02, 2013, 08:37:22 AM
Mark- �Nice to hear you were able to make it all work for you. �At times I�ve had my doubts that I�ll get it to fit. I've had the tub on and off at least 10 times so far.

Now that you are in the paint stage I consider you one of those knowledgeable Jeep guys here on the 3A page. �I have a fit up question. Did you have to move the hat channel (floor support) that needs a hole drilled in it at the driver side floor position? This would be the one that runs up by the master cylinder. �Mine is off by about 3/8� or so. I�m trying to make up my mind. �Do I hog out the hole or move the hat channel? �The purist in me wants to move the hat channel and the Bubba in me wants to hog the hole out.



Steve

Title: Re: CJ3A Body kit
Post by: macrisel on January 02, 2013, 11:51:55 AM
I did not have to move my hat channel as mine matched up very close.  I also bought a Repli Tub from Willys Overland where they drill the mounting holes for you and "fix" the transmission hole.  However, I think that the tolerances at the Omix factory must be +/- 2 inches on most of their blueprints.... :o

To your original question, I would enlarge the mounting hole on the frame before I moved the hat channel.  Before i did that, i would mount the grille and fenders and see how much "play" you have with everything bolted together.  You may have enough to get everything to fit.

Again, quality control is not that great in addition to several different versions of tubs being out there.  The Omix factory does not always use all there old inventory up when they make a change to their design so you may end up with a 2012 tub and a 2009 fender trying to get them to fit together. :-?
Title: Re: CJ3A Body kit
Post by: Bob W on January 02, 2013, 12:57:01 PM
Quote
Do I hog out the hole or move the hat channel? �The purist in me wants to move the hat channel and the Bubba in me wants to hog the hole out.

I think Calvin moved the body mount on the frame when he ran into this problem.
Title: Re: CJ3A Body kit
Post by: CJPilot on January 02, 2013, 01:20:00 PM
Thanks Mark,   So another vote to hog out the hole.  That�s what my brother (helper) thought. I can put this decision off until I take the tub off to weld the emergency cable bracket on. In reality I'd only be opening it up about a 1/4"

I have my fenders and grill on.  So I think my tub is mounted ok. The passenger side fender looks off to me. That�s my next project.  

It�s hard for me to figure their quality out.  I think if you are going to go through all the trouble to make the thing why not just make it right. Or at least close.


Steve

Title: Re: CJ3A Body kit
Post by: calvinhunt on January 03, 2013, 01:04:04 AM
Steve,
 ï¿½Bob W is right in his post above, I moved the body mount (outrigger) on the frame (a couple of places on both left and right sides). �However, mine were off by a little more than an inch. �Had they only needed to be opened up 1/4 inch I'm sure I would have done just that. �

 ï¿½In the photo below you can see how far I moved outrigger mount. �You can see that I pilot-drilled just a bit too far into the rivet originally retaining the mount to the frame. Then I drilled the two rivet heads just enough to remove mount. �Any deeper and I may have drilled into the holes of the outrigger possibly elongating them. With the outrigger removed I ground the rest of the rivet shanks flush with the frame (or meant to). �With the outrigger mount clamped to the frame aligned just where I wanted it I match-drilled the hat channel through the outrigger, bolted it to the tub, and then match-drilled the two holes in the frame through the outrigger and mounted it with two AN aircraft bolts. �(http://i389.photobucket.com/albums/oo336/calvinhunt/Outriggerbolts006.jpg)

 ï¿½Another location with similar solution.
(http://i389.photobucket.com/albums/oo336/calvinhunt/JeepwithTaraskids-Lucilleonions006.jpg)
Title: Re: CJ3A Body kit
Post by: CJPilot on January 03, 2013, 01:51:28 PM
Calvin thanks for the advice and the picture.  As I was reading your post and came across �match-drilled�,  I thought airframe?  Then you mentioned AN hardware so now I�m thinking you know your way around AC43-13.

Steve
Title: Re: CJ3A Body kit
Post by: CJPilot on January 03, 2013, 07:16:41 PM
My next issue to fix is the passenger side fender. �It�s primer doesn�t look like the tub or drivers side fender. I'm not sure what that means if anything. � It sits low in the back where it bolts to the tub.

Passenger Side
(http://i1146.photobucket.com/albums/o537/CJPilot1/Publiccj3a/20130101_191754.jpg)




Drivers side
(http://i1146.photobucket.com/albums/o537/CJPilot1/Publiccj3a/20130101_191719.jpg)


Steve
Title: Re: CJ3A Body kit
Post by: James P on January 13, 2013, 08:23:03 PM
I know this is a little late on the subject but that second tank is off an M38a1, seen in the jeep a little while ago. :) (just noticed it)
Title: Re: CJ3A Body kit
Post by: athawk11 on January 13, 2013, 10:02:04 PM
Steve,
Do you have the body mount rubber in position? �If so, you may want to try a thinner mount at the tub to help align it with the fender. �I've read that the original thickness of the mounts varied on these depending on the mount position. �I started with 4 ply tire sidewalls cut to size. �All were about the same thickness, but I did have to adjust the thickness up or down, here or there, to get everything to line up. �It wasn't very scientific. �

If the rubber is not in position yet, and you're already this far off, you will likely have to enlarge the mounting holes on the fender support, and maybe at the three mounting holes... fender to tub...to move the fender up.

Tim
Title: Re: CJ3A Body kit
Post by: macrisel on January 14, 2013, 01:21:25 PM
To second Tim, I had to custom fit each of my rubber mounts to get my tub to sit level on the frame and line up with the fenders.  On one, I had to trim off about 1/2" to thin it out...
Title: Re: CJ3A Body kit
Post by: Gunslinger on January 14, 2013, 10:26:46 PM
I Found a pretty reasonable body mount. I bought a 10 inch long straight roller for a boat trailer. �It comes with the 1/2 inch diameter hole in the center and you can cut it to any thickness on a band saw lor hack saw. This way you can easily adjust body height and its cheap, about 8 bucks I think.
Title: Re: CJ3A Body kit
Post by: calvinhunt on January 15, 2013, 03:11:16 AM
CJPilot,
The last three posts (athawk11, macrisel, and Gunslinger) have answered your misaligned fender very well.  You can see from my earlier response on this thread that I used an old tire to cut rubber mounts.  I got the body where things line up and then custom made the thickness of each rubber spacer.  I especially like the boat trailer roller idea by Gunslinger. Wiksh I would have thought of it. I completely assembled my Jeep before I painted it.  That way all cutting, grinding, and welding was done first.  Then I completely disassembled everything, painted it, and reassembled it.  

PS. I PMed you about the AC43-13 question a few posts back.
Title: Re: CJ3A Body kit
Post by: macrisel on January 15, 2013, 09:38:58 AM
My body kit came with the rubber mounts and like Gun, I also used a bandsaw to cut the rubber.  When I got close with that, I would fine tune the thickness with a table belt sander with a 120-180 grit belt.  Just don't hold the mount on there too long at one time or you end up melting it instead of cutting it!
Title: Re: CJ3A Body kit
Post by: CJPilot on January 15, 2013, 06:22:43 PM
Thanks for all the great help guys. I'll be going to the marina. �I�ve been very busy at work and trying, but failing, to get our skating rink going.

(http://i1146.photobucket.com/albums/o537/CJPilot1/Publiccj3a/20130104_174452.jpg)

It's hard to see much detail in this picture but, I mounted both fenders, put the bolts in at the grill and clamped the fenders in the proper orientation / location to the tub. It looks pretty good. :) �My hood lines up nicely as well. :o Of course by doing that most of the holes don�t line up so I have decided to weld in some plugs and move the holes were they need to go.



(http://i1146.photobucket.com/albums/o537/CJPilot1/Publiccj3a/20130104_120048.jpg)
Making the 5/8" plugs after I couldn't find any at the hardware store

I have mounted both the repo and my original windshield and I�m going to go with an original I think. �The original just looks better. �Unfortunately my windshield is in rough shape. �I�ll use it until I can find a better one.


Steve
Title: Re: CJ3A Body kit
Post by: garage gnome on January 16, 2013, 08:33:45 PM
I hope the visit out here helped too! Keep messing with the repop kit and you will get it right.
Title: Re: CJ3A Body kit
Post by: CJPilot on April 21, 2013, 08:33:32 PM
Had a little time to work on my Jeep today. ;D
I have made good but slow progress on the body kit and I�m now attacking the front fenders. �My driver�s side fender wasn�t too bad, I had to move or enlarge a hole or two and I could make it work. The passenger side fender is a different story. I had to move and fill holes but I ran into a bigger problem with this fender. �The brace that bolts to the frame was off by over ��. That made it impossible to get the bolts in. So I had to remove the brace.


(http://i1146.photobucket.com/albums/o537/CJPilot1/Publiccj3a/20130421_181605_zps401239b0.jpg)





I drilled out the spot welds

(http://i1146.photobucket.com/albums/o537/CJPilot1/Publiccj3a/20130421_184000_zpsb1eb061d.jpg)



Here is a picture of the brace in the correct location. You can see how far off it was.
(http://i1146.photobucket.com/albums/o537/CJPilot1/Publiccj3a/20130421_185302_zps1019c033.jpg)

Next I�ll plug weld �the brace in with everything bolted up.


Steve
Title: Re: CJ3A Body kit
Post by: calvinhunt on April 22, 2013, 12:14:55 AM
Steve,
  I had the exact same issue on my CJ-3A MD Juan body kit.  However, surprisingly I restored a Willys MB for a pilot friend (you may have seen the pics with his Jeep in front of the B-17 on another post) and the tub, fenders, grill, etc. all lined up perfectly.  I guess they have more old Army Jeeps in the Philippines than they do CJ-3As.
Title: Re: CJ3A Body kit
Post by: CJPilot on April 22, 2013, 07:50:23 AM
[size=14]Calvin, I�m hoping MD Juan makes good on their attempt to improve the quality of their reproduction body kits. �This amount of error has no justification. �I wouldn�t buy another one without reading some positive reviews from people using a repo body kit. �Funny thing is if they straightened out the quality I feel they would sell a lot of them.

At least I think I have �turned the corner� and I should be in good shape moving forward. I was delayed by family obligations, some good, some bad. And now that Youth Hockey is over for the season I should have some time to devote to the 3A.

Steve
[/size]
Title: Re: CJ3A Body kit
Post by: CJPilot on May 03, 2013, 08:07:03 PM
I did a little more test fitting the body.� Front fenders line up good.�

I will now need to rework the area around the transmission and transfer case shift levers.� They seem to be off by about an inch.

I drove it out side for the first time in a year. :D� �

(http://i1146.photobucket.com/albums/o537/CJPilot1/Publiccj3a/20130503_180638_zpsb26175be.jpg)

Steve
Title: Re: CJ3A Body kit
Post by: garage gnome on May 03, 2013, 10:34:16 PM
That looks familiar!

(http://i748.photobucket.com/albums/xx125/willyscjmj/1953%20Willys%20CJ3A%20Jeep%20Restoration/100_4981.jpg) (http://s748.photobucket.com/user/willyscjmj/media/1953%20Willys%20CJ3A%20Jeep%20Restoration/100_4981.jpg.html)
Title: Re: CJ3A Body kit
Post by: CJPilot on May 04, 2013, 09:56:25 AM
[size=12]Hi Nate, That�s funny. I guess we all go down the same path more or less as we rebuild these Jeeps.[/size]

Steve
Title: Re: CJ3A Body kit
Post by: Ryan_289 on May 06, 2013, 10:16:30 PM
This is a little late but here is another suggestion for body mounts.  I work at a John Deere dealership and I used old round baler belt that we had laying around.  As these are used the tread wears off and you end up with varying thickness.  Worked perfect for me.  These are just scrap pieces from when we replace sections of belt in the shop.  I could cut up some for anyone wanting some.  If you walked into the local dealership shop one morning with a box of donuts you could proabably get some scrap pieces for free.
Title: Re: CJ3A Body kit
Post by: garage gnome on May 07, 2013, 07:19:48 AM
This is what I do for body mounts. Very inexpensive and works very well.

(http://i748.photobucket.com/albums/xx125/willyscjmj/1953%20Willys%20CJ3A%20Jeep%20Restoration/DSC01068.jpg) (http://s748.photobucket.com/user/willyscjmj/media/1953%20Willys%20CJ3A%20Jeep%20Restoration/DSC01068.jpg.html)
Title: Re: CJ3A Body kit
Post by: ZekeD on May 07, 2013, 01:41:57 PM
Nate,  is that a hocky puck?
Title: Re: CJ3A Body kit
Post by: CJPilot on May 14, 2013, 07:33:15 PM
[size=12]I had to move the cut out for the transfer case shift levers about �� due to my shifters hitting.
(http://
http://i1146.photobucket.com/albums/o537/CJPilot1/Publiccj3a/20130504_073353_zps923d4a0a.jpg)

I marked the area I planned on cutting and cut it out with a saw.
(http://i1146.photobucket.com/albums/o537/CJPilot1/Publiccj3a/20130504_115009_zpsa80e9f50.jpg)

Once cut out I welded it into the proper position

(http://i1146.photobucket.com/albums/o537/CJPilot1/Publiccj3a/20130504_125643_zps55157dcd.jpg)

(http://i1146.photobucket.com/albums/o537/CJPilot1/Publiccj3a/20130504_135311_zps871d8cd0.jpg)


Steve

[/size]
Title: Re: CJ3A Body kit
Post by: CJPilot on May 14, 2013, 07:44:31 PM
(http://i1146.photobucket.com/albums/o537/CJPilot1/Publiccj3a/20130511_183337_zps2f3e3607.jpg)

[size=12]This doesn�t look like much of anything but I spent a lot of time measuring, filing, drilling and fitting the switches, plate, light and gauges.� If you are considering a repo tub, plan on this taking some time. It�s not a fifteen minute job.�

Steve
[/size]
Title: Re: CJ3A Body kit
Post by: 1955CJ-5 on May 14, 2013, 08:04:23 PM
Looks good! I've read that the transmission opening is not correct in the repro tubs...now I see what they mean.

Almost looks like they flipped the template or something between measuring and stamping.

Nice repair!