My Willys 3A and 3B Community

3A, 3B, DJ Technical Knowledge Base => "Original"-- Technical Questions, Answers, Observations => Topic started by: SAWCo69 on May 05, 2012, 09:47:30 AM

Title: Fuel issues
Post by: SAWCo69 on May 05, 2012, 09:47:30 AM
1950 CJ3a, fuel suppy problems, is the system vented anywhere? gas cap that I have does not seem to be vented...is that correct?
Title: Re: Fuel issues
Post by: Carls_jeep on May 05, 2012, 05:35:37 PM
The cap is vented. What are your problems?
Title: Re: Fuel issues
Post by: SAWCo69 on May 05, 2012, 06:19:31 PM
Runs fine when cold, at operating temp, the fuel pump does not want to pump. Glass bowl shows about an 1/8 inch fuel, small bubbles.Seems like a vaper lock, but all lines are in stock position and don't appear even warm.All new lines on suction side,all joints are tight.
After sitting for a hour or so, starts pumping fuel and off we go...
New fuel pump does same thing.No spacer at pump, I think that would get a little more fuel pressure, but don't think new Solex carb needs it.
New tank, I may pull it just to make sure there are no odd bits swimming about.
A bit baffeled at this point.
Title: Re: Fuel issues
Post by: athawk11 on May 06, 2012, 11:34:58 AM
Saw,

It really sounds like vapor lock.  Vapor lock has been a topic here and on the 2A page. I have a Solex also.  I'm not sure if that is a factor, but I made special effort to run my fuel lines as far away from the manifold as I could, but as close to the original look as possible.

If it were a clogged fuel delivery, it would probaby react the same way, cold or hot, but more so when you are hard on the throttle.

You could try to re-route the fuel lines further away from the manifold.  Or temporarily install an electric pump.   You could also wrap some cool rags around the fuel line from the pump to the carb, and get it up to operating tempurature and see how it reacts.  These approaches would at least eliminate vapor lock as a possible issue.

Tim

Title: Re: Fuel issues
Post by: aboyandhisdog on May 06, 2012, 12:39:28 PM
Your fuel pump delivers about 3 3/4 lbs. pressure, but the Solex requires 1 1/2 - 2 lbs.  This is why you have to have a pressure regulator in the fuel line before the carb.  Do you have one?  Are you saying the jeep just quits running after it is hot, or is it just hard to restart after you have shut it down when hot?  If it shuts down when running, I would concur with Tim on the vapor lock.  If it is just getting too much heat after being shut down, this is a pretty common problem with the Solex or the Carter.  Mine will fire up with the use of the acc. pedal when hot, but having the right fuel pressure might be necessary for your Solex.
Title: Re: Fuel issues
Post by: Carls_jeep on May 06, 2012, 07:54:31 PM
Try this, run the Jeep until it is warmed up good and stops. Be sure to take a tool kit with you. Pull the fuel line at the carb and turn the engine over to start it. Does fuel come out the line? If it don't then you may be getting vapor lock but if fuel comes out quickly and a good flow then you may have an ignition problem.

BTW, have a can to put the fuel line in so it don't spray fuel on the hot engine.

Or, leave the fuel line connected and check the ignition for fire to the plugs. You could have a bad coil, bad condenser or both.

I only had a vapor lock on my Jeep at 11,000 feet on a mountain with a weak fuel pump and it was not a hot day, just the conditions.
Title: Re: Fuel issues
Post by: garage gnome on May 06, 2012, 09:58:18 PM
Quote
Runs fine when cold, at operating temp, the fuel pump does not want to pump. Glass bowl shows about an 1/8 inch fuel, small bubbles.Seems like a vaper lock, but all lines are in stock position and don't appear even warm.All new lines on suction side,all joints are tight.
After sitting for a hour or so, starts pumping fuel and off we go...
New fuel pump does same thing.No spacer at pump, I think that would get a little more fuel pressure, but don't think new Solex carb needs it.
New tank, I may pull it just to make sure there are no odd bits swimming about.
A bit baffeled at this point.


My '49 is doing the same thing too, but I have a Carter. Good fuel supply, good spark, decent compression. Was running fine a few weeks ago and not so well now. �[smiley=angry.gif]

I still need to tear into it and see whats up.
Title: Re: Fuel issues
Post by: SAWCo69 on May 07, 2012, 09:29:25 AM
 ï¿½ Sunday afternoon,put a new fuel pump on the little red beast, put tools in and drove in circles around the hood till it got to temp (about 20 min) a couple of sputters and it died, again. Fuel pump is not pumping fuel.At this point makes a regulator rather moot......walked home...a few hours later it fired right up and off we went.
 ï¿½ Current plan is to re-rout fuel lines , maybe install elec pump. Stay tuned.
Thanks for the replies.
Title: Re: Fuel issues
Post by: Carls_jeep on May 07, 2012, 01:16:32 PM
If you disconnected the fuel line and it would not pump fuel out I don't think it's the fuel pump. It may have something floating around in the fuel tank that finally gets sucked over the outlet in the tank.

A vapor lock is usually between the fuel pump and the carb.
Title: Re: Fuel issues
Post by: Williamsmar on May 07, 2012, 02:25:43 PM
I bought a 53 chevy truck would idle great and run good for about 1000 yds and die >:(.  changed out fuel filters even added a secound one due to paticles in fuel bowl.  Took tank out took rubber hammer to it and dumped out $35 of change covered with laquer from old gas.  cleaned tank ran like a charm thereafter.  I think you have something in the tank.

That is my newbie expertise.

Marty Williams
Title: Re: Fuel issues
Post by: Macgraham on May 09, 2012, 08:51:53 AM
When I was a kid in Colorado vapor lock was common because of the high altitude at home. Our 3A never had much trouble but some guys would put a row of clothes pins on the fuel line to dissipate heat. It must have worked cause I remember rigs using them alot. Maybe a guy could figure something else that looked a little better. Mac
Title: Re: Fuel issues
Post by: Carls_jeep on May 09, 2012, 09:09:49 AM
I had a car that would vapor lock on a hot summer day. I cured it by putting a bypass line from the pressure side of the fuel pump at the carb to the inlet side of the fuel pump. It kept the fuel flowing but I did us the 1/8" OD plastic line to restrict the flow.
Title: Re: Fuel issues
Post by: SAWCo69 on May 10, 2012, 09:08:36 AM
   I am at 7000 ft in CO, but vapor lock has not been an issue before,not hot weather yet, but that was then and this is now... I am currently rerouting the exhaust line ( PO had it different than stock), then the fuel tank is coming out for a good look see.The little red 50 will run sooner or later,more likly later as I'm off to Moab with the 75 crawler for a week.
Thanks for the tips, if I see some clothes pins I'll give it a try....
Title: Re: Fuel issues
Post by: rocketeer on May 10, 2012, 03:59:20 PM
What would really help are photos of how your fuel lines are routed and how it's connected to the tank.

Larry
Title: Re: Fuel issues
Post by: SAWCo69 on May 20, 2012, 09:57:32 AM
 Back from 4 days in Moab, love that town.
Finished up moving the tail pipe this morning.
Pulled the fuel tank, its only two years old, got all the fuel out but a small amount that hides behind the internal baffle.
 Two small bits of junk found, seem too small to clog fuel line. Reinstalled tank, seats, lines etc. Installed 5/16 hose barb in tank drain, ran fuel line up to engine.This will be my back up fuel line if the other still won't act right. Added a elec. fuel pump to the jeep tool box, some wire, and set out on another test flight.
  1 1/2 hours of good jeep driving, around town , up to the airport, out to a buddys pond, up, down, around.Feeling rather smug with myself, great wrencher and all.Headed home thru town and.....sputter, cough, die....dead red jeep by the side of the road.Much screaming, grinding of teeth and pulling of hair, choice words said.No fuel in glass pump bowl, no pumping fuel.
  Unhooked original fuel line from pump, jammed fuel hose from tank drain on and fired right up......drove home bewildered.
Will do another test flight today just running off the drain line.
Stay tuned.......
  
Title: Re: Fuel issues
Post by: rocketeer on May 20, 2012, 02:01:41 PM
Which outlet do you consider to be the drain? Is your line connected as shown in the photo?

(http://i863.photobucket.com/albums/ab191/rocketeer_2010/Jeep/FuelLine1.jpg)

Larry

Title: Re: Fuel issues
Post by: athawk11 on May 20, 2012, 09:58:32 PM
Saw,
I agree with Larry(Rocketeer)  Pictures say a thousand words. �You would be surprised what the members here might see that may help solve your issue.

Besides, you live in Colorado. �I live in Colorado (Arvada). �If I ever see your Willys on a drive, I'll know who I'm chasing down.

Tim
Title: Re: Fuel issues
Post by: SAWCo69 on May 21, 2012, 08:48:16 AM
Did take some pics on Sunday , but can't seem to post them.
Sundays test flight ended in failure, dead jeep by the side of the road.
A bit of a bus ride, a walk and then towed Little Red home.
Stay tuned....
Title: Re: Fuel issues
Post by: athawk11 on May 21, 2012, 11:51:31 AM
Posting pictures is a bit of a challenge...but nothing like the challenge you are facing with your Willys.

The easiest way to post is to us a secondary photo site like www.Photobucket.com

It is free...you can easily download your photos there...then from there, you can move them into your post.  There are some posts on how to do this, but some still seem to have trouble.  Could be an Internet Explorer or Firefox thing.

Look in the Web Site Feedback area for help.

Tim
Title: Re: Fuel issues
Post by: calvinhunt on May 21, 2012, 05:26:07 PM
Quote
Installed 5/16 hose barb in tank drain, ran fuel line up to engine.This will be my back up fuel line if the other still won't act right. Added a elec. fuel pump to the jeep tool box, some wire, and set out on another test flight.
 ï¿½1 1/2 hours of good jeep driving... � ...sputter, cough, die....dead red jeep by the side of the road.
 ï¿½Unhooked original fuel line from pump, jammed fuel hose from tank drain on and fired right up......drove home bewildered.
Did you hook up the electric fuel pump as you switched to the use of the 2nd fuel line (the backup 5/16 fuel line you installed in the tank drain port) or just drive home on the backup fuel line?
A friend has a CJ-2A that I drive from time to time. �He has an electric fuel pump installed in the fuel line just down stream from the fuel tank. �That Jeep acts strange. �It will drive for 30 minutes to an hour with the elec fuel pump off without hesitating, up hills as well. �Then it will sputter, cough, and die. �It will not start unless you turn on the elec fuel pump. �Turn on the pump it starts instantly. �The owner just drives with the in-line fuel pump always on. �It never dies. �Sounds like that may be a solution.  I don't know what the answer is.
Title: Re: Fuel issues
Post by: rocketeer on May 21, 2012, 07:10:54 PM
It sounds to me like a vented cap problem but we're not getting specific answers, info or pics so it's difficult to judge.

Larry
Title: Re: Fuel issues
Post by: SAWCo69 on May 21, 2012, 08:11:27 PM
Sorry about the lack of specific answers, info or pics, my current level of frustration with the 50 is spilling over into my computer use......
 1.) Drilled a hole in a fuel cap, stuck a 1" chunk of brake line thru it, instant OSHA approved, vented for sure gas cap.This was installed before the last test flight.Did not seem to make a diff.
2) Have not hooked up the elec. fuel pump yet ( the backup line from the drain seemed to work on test flight #1, but not yesterday on test flight #2) plan to install elec pump in backup line and try.Bit worryed about too much presure for Solex carb,not sure if I'll need a presure reg.
3.) Will get pics up sooner or later.
4.) Thanks for the encouragement.
5.) Athawk11, I'll be the Dead Red 50 Willys by the side of the road.
Title: Re: Fuel issues
Post by: SAWCo69 on May 21, 2012, 10:30:31 PM
Did manage to post some pics in the Web Feedback thread, can't seem to doit here....(http://)
Title: Re: Fuel issues
Post by: rocketeer on May 22, 2012, 09:53:07 PM
Can you take a pic that shows the whole area from the pump up to the carb including the fuel line?

(http://cj-3a.com/forum/Attachments/Picture_009_opt.jpg)

(http://cj-3a.com/forum/Attachments/Picture_011_opt.jpg)

Larry
Title: Re: Fuel issues
Post by: SAWCo69 on May 23, 2012, 08:23:47 AM
Posted a pic of fuel lines from pump to carb in Web Feed Back thread
Sorry, but still can't get any posted in the Tech Section.
Rocketeer, thanks for finding my pics and moving them......
Title: Re: Fuel issues
Post by: rocketeer on May 23, 2012, 08:44:43 AM
Upon seeing this pic, the first thing I would advise is to install a correct metal line all the way up to the fuel pump, with a correct short flexible connection. It's never a good idea to use soft line on the input (suction) side of a pump. A long rubber hose like that has a tendency to suck closed, especially after heating up from the engine.

(http://cj-3a.com/forum/Attachments/Picture_010_opt.jpg)

Larry
Title: Re: Fuel issues
Post by: athawk11 on May 23, 2012, 11:09:33 AM
Hey Larry,

I think these photos may be showing his temporary fall back approach.  A prior post mentions the 5/16" fuel line from the tank drain to get him down the road when he has issues.  Looks like there is a steel line connected to the tank in the right position, but I can't see how long or how far the steel line travels before it reaches the engine compartment.  

So...Saw,
As Larry points out, the original set up is steel from the front hole in the tank until it is within about 6" from the pump.  It then has a short rubber connection to the pump.  It was done this way to give the line some flexibility between the engine movement and the more rigid chassis and fuel line connections. It reduces the chance of a fuel line break.

So, on your standard original setup, if you have a long rubber line attached to a short steel line, Larry's thoughts are true.  (By the way, Larry's thoughts are always true.)  Upon heating up, the rubber could compress under pressure from the pump.  Similar to what happens on an older lower radiator hose that causes overheating.

Ther routing of the line from the pump to the carb looks good.  Good and far away from the manifold heat.

I read in another post that if the cam shaft has movement, the arm on the pump can slip off the lobe and cause the pump to stop pumping.  Could this be a factor?

Tim  
Title: Re: Fuel issues
Post by: SAWCo69 on May 23, 2012, 09:22:04 PM
Yes, this pic shows the fall back rubber line that goes to the tank drain.
  I installed a set of orginal steel lines,back when this all started. If you look closely you can see the short rubber flex hose (with a bolt plugging it) that I substituted for the orginal flex line, the orginal screw-on flex line was about 1 1/2" too short, so I installed a hose barb on the suction side.This makes changing the lines much easier when I'm broke down by the side of the road....
   Today I installed an elec pump near the tank, on the frame rail.The rubber line is then connected to the suction side ofthe mech pump.Thinking is that the cam operated pump will pull fuel thru the elec pump, if the mech pump won't pump I switch on the elec and the mech pump will act as a pressure regulater.
  This seems to work in the shop........on the road may be another thing.Raining to hard for a test flight.
  Really would like to take the jeep camping in Brown's Park this weekend.It went last year and was a big hit, of course that was the last gasp for the engine, current rebuild being the result.But Brown's Park really is past the middle of nowhere,bad place to break down. Not a lot of confidence in the jeep right now.
Thanks again
Title: Re: Fuel issues
Post by: rocketeer on May 24, 2012, 06:32:08 AM
I give up. When we finally get pics they aren't current. How the heck are we supposed to help? I'm out of this one.

Larry
Title: Re: Fuel issues
Post by: Carls_jeep on May 24, 2012, 11:20:20 AM
When your trouble shooting a problem you can't use a shotgun approach. You have to stop and think the problem out. To get it home use what ever method you can but when you approach the trouble shooting method it has to be organized and systematic. Once you start pulling things apart you may have destroyed any evidence your looking for.

I was an engine failure trouble shooter at a Cummins distributor and learned early on to be careful and find everything I can before tearing an engine down. Once the engine is disassembled your testing is done and everything is visual from there out.

To many times people start tearing something apart without knowing what they are looking for or having a plan.
Title: Re: Fuel issues
Post by: athawk11 on May 24, 2012, 11:31:54 AM
Okay SAW,
I see it now. �With that short hose connected, you really shouldn't have the fuel line squeeeeze. � �Could the pump or cam lobe be the problem? �I read in another post, maybe Carl, that had issues at altitude with a weak...old fuel pump. �Your pump doesn't look old, but you may have done a good job of cleaning it up. �

This link dicusses similar, but other fuel issues. �It talks about the lobe on the cam sliding too far forward making the pump inactive. � �

http://www.thecj2apage.com/forums/fuel-problems_topic22983_page3.html?KW=fuel+problems

Again, not sure this is your problem, but other parts of this thread may help you troubleshoot.

Tim