My Willys 3A and 3B Community
3A, 3B, DJ Technical Knowledge Base => "Original"-- Technical Questions, Answers, Observations => Topic started by: bretto on February 03, 2012, 10:55:51 AM
-
I didn't want to hijack macrisel's post about wire clips so I will start this post to ask and hope Calvin chimes in.
I'm sure Calvin, you use that avaition wire like bailing wire and just have spools and spools of it �:). �
I'm far from doing any wiring on my M38 but the question is fresh on my mind. �Is that mil-spec wire a cloth bound wire? �If so, do you have a good source for it given your background? �I dont know that I'll like the look of a modern day pvc coated wire and I wont fork out the $$$$$$ for a premade wire harness.
Also curiosity is asking, on an aviation application, are wire termination supposed to just be crimped, crimped @ solder, crimp and sealed, or?
-Brett
-
Brett,
�Yes, I have available to me any gauge MIL-Spec wire and any MIL-Spec connectors that may be needed in the aircraft maintenance shop where I used to work. �Many of my previous post have included pics showing my Jeep in the fine shop among the flying machines. �When I made my wiring harness I ordered a 100 ft roll of the wire gauge I was going to use the most (16 gauge I think). �It cost me about $30. �What was left over I traded for the short runs of heavier gauge I needed. �I was able to use most of the bulb sockets and terminals unique to the Jeep harness from my old harness by uncrimping or unsoldering and inserting the new wire. �Now when I was rebuilding Mike's, 44 MB, my friend who lives there in your home-town, we chose to buy a harness from Walck's. �It was a beautiful harness and worked very well. �It was made of the original style cloth braid insulation with color coding woven into the braid. �Sockets and terminals were perfect, but it was expensive. �However, Mike didn't have enough left from his original harness to reuse the bulb sockets and other special terminals needed. (You've got to get over and see his Jeep and his old WWII trainer aircraft we restored before we restored the Jeeps.) �
The military specification MIL-W-22759/16 is required by the Federal Aviation Administration for all wiring used in aircraft. It comes in all gauges. The insulation is not cloth, but per the MIL-Spec is made of polytetrafluoroethylene (PTFE) which provides enhanced mechanical toughness and exceptional resistance to heat, radiation and chemicals. The conductor is made of multiple strands of copper and tin coated.
To answer your curiosity: On an aviation application, unless specifically indicated otherwise per the aircraft manufacturer's maintenance manual, a MIL-Spec connector may be simply be crimped and be considered complete. Most often crimped connections are also soldered. Usually heat shrink is satisfactory but on some applications the connection must be potted (sealed) with MIL-S-8802 potting compound. �This is a two-part self vulcanizing rubber compound. �
On my Jeep harness I crimped and soldered each connection. (Mice won't nibble on it and it won't chafe, so in another 60 years when my Jeep has rusted away the harness will still be as good as new.)
I don't know where you could get cloth bound wire, but if you think you would like some of the aviation stuff I can get it for you at wholesale.
-
Hey Bretto.
Sounds like Calvins wire harness is nearly bullet proof. I was with you on a vintage look, and ultimately bought a Walcks 3A harness. They are really quite beautiful. I think I paid $236.00
The M38 has all black wire with numbered metal tags. If you want cloth wire, and are determined to make your own, I found a guy on Ebay selling multiple lengths and gauges of the cloth stuff. His name is "enginebarn". Just search for 'cloth wire' or specifiy the gauge, like '12 gauge cloth wire'.
I needed to modify my Walcks harness a bit. I had a starter solenoid, and forgot to discuss that with Walcks. I was able to make what I needed with the cloth wire, some bullet style connectors, a soder iron and some heat shrink tubing. I also found a guy on Ebay that sells multiple sizes of the 'asphalt wire loom'. (made in the USA)
Just some additional options for you.
Good luck,
Tim
-
I feel that I should add something about the harness that I made for my Jeep. �Because I'm too fussy and inexperienced with harness building, it took me longer than I thought it would to make a simple CJ-3A harness. �Had I been paid minimum wage for the hours I spent building my harness I could have purchased a nice ready-made one from Walck's and had money left over. �Just for what it's worth.
-
Years ago at the shop I worked at one of my specialties was I used to rebuild vehicle harnesses damaged in accidents and fires. I've had lots of experience and with all that experience I choose to buy a pre-made harness from Walcks. It just wasn't cost effective to try and gather all the correct color wires and connectors and then do all the labor myself, not to mention the aggravation. And with Walcks, they offer modified harnesses for the likes of with or without turn signals for instance. Kinda like Burger King, "We make it your way!" Great guys to work with.
Larry
-
Thanks guys.
I'm on a budget and as this project goes, I have done everything this far 100% myself. Ok, I lied, have to give my wife credit for the 30min of wirebrush grinding of the leafsprings. Anyway I dont mind the work and will be doing my own wiring. I kinda have to anyway being my M38's electrical system is going to be 12v but I'm going to incorporate the military equipment into it for the look of it all.
Calvin, does that mil-spec wire only come in white? I have seen a few website co. that offer the wire cloth wrapped modern wire. I dont know for sure what I'm going to use.
What are you guys using to bound your harness together? I'm not a big fan of plain old electrical tape as over time it gives up and leaves a gooey mess and I dont like the look of those corrogated plastic looms. I thought about that self vulcanizing tape. There is a product that is a spiral wrap wire loom that is an open design that I like to.
Brett
-
The "asphalt wire loom" that Tim mentions above sounds like the best product for bundling wires with a period look. I would also use the plastic coated cloth covered wire as well. If you add up the cost of all the individual parts, wire, loom, sockets, shipping,etc. it may cost more to do it yourself. My 2 cents.
-
bretto, if your on a budget and only have so much to spend use ordinary wire from an auto supply house and do your own wiring. There are wiring diagrams on the net or in manuals and it is so easy to wire a Jeep it's crazy. The Jeeps are not modern complicated vehicles, they are basic and simple. You don't need to make a loom. Just wire each component one at a time and then bundle the wires with wire ties.
If your making a Jeep to put in shows and win trophies then spend the money. If your making a Jeep to enjoy keep it simple.
The term is KISS and that means Keep It Simple Stupid. Which in no way implies your stupid, it's just an expression.
At some point when you start "restoring" a Jeep you have to decide how much you want to spend, how much time you want to spend and how perfect it has to be.
Regardless of what you decide your Jeep will be happy and you have to decide if you will be happy too. �
-
Calvin, does that mil-spec wire only come in white?
The MIL-W-22759/16 which is required in planes by the FAA only comes in white. There are other MIL-W-xxxxx/xx wire types that come with differing colors of spiral trace lines as identifies but I have never used any. I can see that the aviation wire would really look foreign to most Jeepers, but to me it looked proper because I'm so used to it. Sounds to me like you would like the period looks of the cloth insulation and I don't fault you at all for that. Some good possibilities have been mentioned here and you said you had an idea of your own. Having seen your Jeep a couple of different times and seeing how well each component is being restored, I know that what ever you install will look great. I think one of the greatest things I've enjoyed about this 3A site is how, after getting ideas from other members, each and every Jeep owner is able to do exactly what he wants to do with his Jeep.