My Willys 3A and 3B Community
3A, 3B, DJ Technical Knowledge Base => "Original"-- Technical Questions, Answers, Observations => Topic started by: athawk11 on April 06, 2011, 04:56:18 PM
-
I have a CJ3A with a GPW flat head L134. �Currently, the vaccum wiper gets its power from a hose that is attached to the manifold.
Is this right? �
This is all coming to light because I want to install a mechanical fuel pump. �(Prior owner installed an electric fuel pump which causes the jeep to run rich.) �It seems there are fuel pumps available with and without vaccums for the wipers.
I only have one wiper motor on the driver side. �It doesn't look like a second wiper motor was ever installed on the passenger side.
In 1949, was it an option to have the passenger side wiper?
The existing wiper motor seems under powered. �Is this common with vaccum wiper motors?
-
Your jeep originaly came with a combination fuel/vacuum pump which powered the wiper. I have seen both single and dual wiper setups on these Jeeps. I'm not sure if the dual setup is an original option or not. My 49 has a wiper moter on drivers side and a hand powered wiper on the passenger side. Gave the passenger something to do on rainy days.
:)
-
The CJ3A should have, as mentioned, a dual action, fuel/vacuum, pump. Keep in mind that if you install a dual action pump on your 3A, you will also need to install a spacer between the pump and block. Bob W has some additional info on his website.
http://www.cj3a.info/tech/fuelpump.html
Larry
-
I appreciate the responses. I think I need to add a hand wiper to the passenger side.
On the Vacuum, this is a 1945 GPW L134 Motor vs. a true CJ3A motor. Do the same rules apply regarding the fuel pump and wipers?
-
Yes.
I'm sure someone has already mentioned this but there are GPW guys over on the G503 forum who would undoubtedly make you a heckuva deal for your GPW engine. Might even swap a CJ engine plus some cash for it.
Larry
-
So Larry, to be somewhat accurate, I get the duel fuel/vacuum pump, run the wiper motor with the fuel pump, then just plug the hole in the manifold? Right?
Best place for a good repo pump? I'm not overly concerned about absolute accuracy, as this Willys is a CJ, soon to be dressed like an M38, with a GPW motor. The thing is all over the place. Not ever going to win awards, but will be a kick in the pants, summer driver.
I would hate to trade motors. Knowing what I have vs. what I might get is a bit un-nerving. This GPW is tight as a bugs butt and runs very strong. (aside from running too fuel rich) I guess I could toss the idea out there and see what might be.
Thanks,
Tim
-
The fuel pump is only a vacuum booster. The wipers normally run on manifold vacuum. The manifold fitting is connected to the fuel pump vacuum booster and the booster is connected to the wiper motor.
-
I know we had a thread on this on the old forum but I can't find it. Maybe someone else can search. I remember we had several pics posted showing how the vacuum lines ran.
Larry
-
This might be the post Larry is talking about.
http://cj3apage.proboards.com/index.cgi?board=Tech&action=display&thread=1109
-
That be the one! :)
Larry
-
Thanks Matto. �Thanks Larry. �I copied/pasted that link for future reference. �That will be incredibly helpful. �One final question in this post::
I see these things everywhere, but I'm a guy that like to put my hands on something I purchase, or have it on good authority that I won't get screwed over by a cheap vendor. �
Best place to get a quality fuel/vacuum pump without breaking the bank?
By the way, from this forums recommendations, I bought a WIRE HARNESS from Walcks. �It is one of the most beautiful things I have ever seen. I can't wait to install it.
-
I have purchased a couple CJ-3A fuel/vacuum pumps from Walcks and they work good. They also have the necessary spacer too.
-
I'll second Walcks.
Larry
-
I hate to bring this subject up again, but as I started to clean and prep the chassis for repairs, seals, paint etc, I noticed my motor mounts are a bit saggy, allowing the engine to point down. �(1945 GPW engine) So, I intend on replacing the mounts.
I got a good look at the fuel pump mounting position. �The front motor plate where the motor mounts are attached, bends BACK toward the fuel pump location. I don't think a Vacuum/fuel pump will fit.
I have read that the frame brackets were not offset in earlier jeeps. �Mine is a 3A frame with offset mounts and this was done to accomodate a Vacuum/fuel pump.
Was the frame in WWII Willys jeeps more narrow than the 3A?
There is a hexigon shaped brass or bronse spacer/mounting block attached to the motor mount which is attached to the frame. (Driver side only) �This spacer looks like a real manufactured part. It looks cast. �Not some fabrication job. �
With the motor front plate bending back, am I going to have to use a smaller NON vacuum mechanical fuel pump? �
If it kills me, I am going to try to figure out how to add a picture to this. �Stay Tuned.
-
There was an adaptor made to allow a 3A front engine plate to be used on a 2A frame to allow the room needed for the combo fuel pump. It sounds like someone used that adaptor to do just the opposite and adapt an early plate to fit a 3A frame. The easy way to fix that is to get a 3A front engine plate and do away with the adaptor thereby allowing room for the combo pump.
Here's some more info:
http://cj3apage.proboards.com/index.cgi?action=display&board=Tech&thread=1506&page=1
Larry
-
If the engine front plate bends to the rear on the driver's side the vacuum booster pump probably won't fit. Sounds like you are describing the adapter pictured below in the photo from The CJ3A Page. This adapter allowed for using a CJ-3A frame as a service replacement for a CJ-2A frame after the 2A frames had been discontinued. Essentially the adapter enabled a CJ-2A engine with symmetrical mounts to fit a CJ-3A frame with offset mounts.
(http://www.cj-3a.com/DSC01876.JPG)
-
Bob, You are exactly right. I think I figured out how to post photos, but you beat me to the punch.
Here is a photo anyway. �Just when I think I've run into something new, guys like Bob and Larry show me otherwise. �Someday I hope I'm not such a newbie.
That motor mount looks bad to me. �Fan occasionally makes contact with lower part of radiator shroud What do you think?
Thanks again.
(http://www.mywillyspics.com/images/2017/10/04/motormount.md.jpg) (http://www.mywillyspics.com/image/VS82)
(http://www.mywillyspics.com/images/2017/10/04/motormount2.md.jpg) (http://www.mywillyspics.com/image/VVAU)
-
Yep, that's what they did, use the adaptor to adapt an early engine plate to a later frame. The easiest way to correct that would be to replace the front engine plate with a CJ3A plate.
Larry