My Willys 3A and 3B Community
Rambling, Malarky, Rants, Etc. => Rambling, Malarky, Rants, Etc... => Topic started by: NoCoWillys on August 18, 2012, 05:36:44 PM
-
So a couple weekends ago I rebuilt my transmission (t-90) and afterwards, I didn't like how the synchronizer assembly wasn't working quite right. �As a result I ordered a replacement assembly (synchronizer, hub, brass, springs and pawls) from a common willys part supplier. �After getting it, it looked great. �Was a much smoother action than my old rebuilt one. �My old one had new brass, springs and plates but was really really hard to slide. �No burrs or anything, just didn't slide well. � :-/ �
So today I went about installing the new assembly. �Luckily I hadn't installed the transmission back in the jeep and it was still sitting on my kitchen table. �I'm single can you tell? �Anyway, after installing it back on the main shaft I started to run into troubles. �I couldn't get the snap ring to fit into the grove. �The hub just wasn't going down deep enough. �In my frustration of trying to figure it out and going back and forth from the small pictures on my laptop, I thought the hub was on upside down. �So I took it apart, flipped it over and put it back together. �This time I could get the snap right on. �I wouldn't say it was a perfect fit, but I could get the snap ring to fit into the grove enough that I didn't think it was going to pop out. �Success! �Or so I thought. �Next after wrestling with the 14 needle bearings a couple times I was fitting the main gear back into the case. �All was good but I just couldn't get it to slide deep enough into the case to seat the rear bearing. �I had a little more than an 1/8" almost 1/4" before the rear bearing was even touching the rear bearing retainer. �>:( �At this point I went and played with the dog before I tossed the transmission out the window. �
Coming back I decided to get on my big computer with a big screen so I could make sure I was putting everything on correctly. �At this point I did determine I was stupid and I did have the clutch hub on correctly the first time. �So I pulled everything apart. �As a test I pulled everything off the main shaft except the retainer and the rear bearing. �It fit into the case and seated perfectly. �So I reassembled the main shaft with the clutch in the right direction and again I ran into not being able to put the snap ring on. � >:( �I suppose I could go and grind down the snap right just a slight bit and it would have fully seated (it was so close) but that didn't sound like a safe option to me. �
I pulled everything apart and started comparing the clutch and synchronizer. �They looked good but something was off. �I used my micrometer and measured the thickness of the clutch hub. �Sure enough, my original one was .835 and the new one was .837. �That .002 was about all I was off in getting the snap right in place. �So this time I went back to my original synchronizer and hub but used the pawles from the new assembly because my guess was the replacements I had gotten during the rebuild were what were causing the slide issues. �What do you know? �The snap right fit on perfectly! �This time when I installed the main gear into the case, everything slid together and the rear bearing seated perfectly. �Things are turning better and the synchronizer and hub slide like they should. �
So... very long story but in the end, I would have been better off saving my $70 bucks on this shiny new paper weight and gotten about $10 worth of pawles instead. �
Now if my luck would just improve with the transfer case (d-18) things would be looking up! �Oh but they aren't. �After getting everything stripped apart, cleaned up, painted, I was going to start assembling this morning with the master rebuild kit I got from Novak. �While making sure everything was there and ready to go I noticed the nice fancy new intermediate shaft I got from them wouldn't fit inside the bearings for it. �I then held it up to the case and the shaft was too big. Measuring it, it is a 1 1/4" shaft. �Mine is 1 1/8". �I double checked my order, yep I ordered the 1 1/8" kit. �I measured the bearings and they are for the 1 1/8" kit. �When they assembled the kit they put the wrong shaft in with it. �I'm sure they will make it right when I call them Monday, but I'm out another week waiting on shipping. �Anyone have a beer?
Cheers.
-
;D man, I know exactly how you feel. When I rebuilt my tranny/transfer cases I did a lot of searching and found out that you do not want to buy any tranny/transfer parts made overseas. I bought all my parts from Novaks and DeBella and told them I want ONLY parts made in the USA and NOS parts.
There are several threads here and on the CJ2A site that tell tales of woe from using parts from overseas. I know Novaks will make it right for you, they are a very good place to buy Jeep parts.
It's getting harder and harder to find NOS parts and parts made in the USA but they can be found in most cases.
-
I found Tcase bearings made in Canada and they were good for fit. Not much time on them yet. Some of the parts suppliers I use to deal with are only interested with you're $$$ and not Jeeps at all. Just my opinion anyway. mac
-
I can only wish this was the first time I've heard a story like this. Rebuilding these beautiful little vehicles is a big enough challenge without having to deal with mismatched parts from suppliers.
Novak is a good outfit. And we are all human. Not to hope ill will on anyone, but I just wish they could occasionally show their human side on someone other than me.
Hmmm, I guess I got my wish. Sorry NoCo ;) In all honesty, I feel for ya' man.
Tim
-
Thanks everyone. Novak has already shipped the replacement shaft to me so I'll have it in a few days. I suppose I should clarify who I got the crappy synchronizer assembly from since people are assuming Novak and I don't want them to take the blame for it. I got it from kaiser willys. The up side was Novak was really easy to deal with when I called them and didn't try to hassle me or anything. They are making it right as quickly as they can.
:)