My Willys 3A and 3B Community

Your Projects => Your CJ-3A Project => Topic started by: Medsker51 on February 19, 2014, 05:40:50 AM

Title: My cj3A
Post by: Medsker51 on February 19, 2014, 05:40:50 AM
So I just picked this up last week. From my research the "451" on the plaque means it is a 1951. The engine number is "4LR190690" I am sure I will have many, many questions for the forum and am glad I found it.

My first question is what is up with the tail lights. They don't currently work so I don't know which is brake lights/running lights/turn signals/etc. The three round ones look stock but the oval one may or may not be. It's hard to tell from the picture but the oval one sticks out a couple of inches. I haven't seen any other pics of one like it on the internet.

Thanks, Medsker
Title: Re: My cj3A
Post by: garage gnome on February 19, 2014, 06:49:30 AM
First off, welcome to the site!

Yes, that is indeed a 1951 with that VIN. Your engine is a factory replacement if I'm not mistaken.

None of those tail lights are stock. There is only supposed to be one on the drivers side near the bottom.
Title: Re: My cj3A
Post by: garage gnome on February 19, 2014, 06:56:55 AM
Info on the stock tail lights

http://www.cj3a.info/tech/taillight.html

And here is the correct location. The oval one probably uses the original mounting holes. I added the second non lit one to mine so I have turn signals.

(http://i748.photobucket.com/albums/xx125/willyscjmj/1949%203A/856638d4.jpg) (http://s748.photobucket.com/user/willyscjmj/media/1949%203A/856638d4.jpg.html)
Title: Re: My cj3A
Post by: athawk11 on February 19, 2014, 07:02:44 AM
Hi Medsker,
Welcome aboard. Looks like a very nice 3A.

The tail lamps look nicely done, but unless there was a factory option I'm not aware of, they are not what your Willys started with.

The factory standard offering would have been one protruding lamp mounted close to the current location of your oval lamp.� There was a dual tail lamp option that added another protruding lamp to the passenger side.

Tim
Title: Re: My cj3A
Post by: athawk11 on February 19, 2014, 07:30:16 AM
When troubleshooting the lamps, the first couple things I would do is install new bulbs and check to see if the two wires are connected to the brake switch mounted at the front of the master cylinder.� If the wires are connected, check to see if one lead heads back to the lamps and is connected to at least one lamp.� The other lead would normally be attached to the main light switch where it will get its power.

If this curcuit looks complete, but you still have no brake lights, the brake switch on the front of the master cylinder may need to be replaced.�

If a fuse was added to your electrical system, you might check to see if the fuse needs to be replaced.

Again, just some starting points.

Good luck.

Tim
Title: Re: My cj3A
Post by: bretto on February 19, 2014, 08:19:31 AM
Welcome,
Nice find, I thought I remembered seeing that 3A on eWillys and KSL.� So where in Utah are you?� I'm in Orem, it'd be nice to come check it out.
Brett
Title: Re: My cj3A
Post by: F Bill on February 19, 2014, 09:45:16 AM
Beautiful jeep. I'm glad you found us!

I am pretty certain you have a totally independent turn signal/four way flasher setup on that jeep. Modern vehicles use the same filament for the turn signals and brake lights, but you have an aftermarket setup that was installed when signals became mandatory to pass inspection.

You should have a power "in" to the switch, then either two or four power "outs" to run the left and right signals. Might also have a ground wire too.

I would bet the lollipop lights in your fenders have a power wire and aground wire , and only function as turn signals.
Which two rear lights are wired the same way is anyone's guess, I would bet the oval light and the lower light opposite it.

Your front small bulbs should function as parking lights only. They also are a single filament bulb, and their power lead eventually ends up at the headlight switch.

The other two rear lights should be dual filament bulbs, one for tail light and one from brake lights.� The dimmer of the two filaments is connected to the tail light circuit, the brighter of the two goes to your brake light circuit.

Here's a wiring diagram for a 2A, the 3A is similar.� Check out all the links on this thread, you might find one of the suggested diagrams will work for you.

http://www.thecj2apage.com/forums/electrical-wiring-and-harness_topic15283.html

Your lights, while vintage, may be in poor shape inside. You have to decide whether you want to go back to original or if you prefer those nice big lights in todays' traffic. If it were my jeep and a daily driver, I'd be putting in modern led equivalents to what you have there.. You can find them at many truck supply places, Ebay, and even your local parts store. (Shop around, prices vary greatly)� If you do stick with what you have, spraying the inside of the lights with silver or white paint will get them as bright as possible.�
Title: Re: My cj3A
Post by: Medsker51 on February 19, 2014, 10:07:01 AM
Thanks for all of the ideas. I was wondering if the tail lights were aftermarket. I really like the look of the inset ones. I may try to take all of them off but the top two. I am looking more for what I like rather than going back to complete stock.

I was under it last night and couldn't believe how rusted out it was under there. I was debating on a new tub and now think I will for sure. If I'm getting a new tub I think I will wire it for 12v.

I also want to replace the tires with something that doesn't need a tube. A nail in a regular tire is easily fixable in the middle of no where and a tube can be but I can't even imagine how hard that would be.

One last question. What is spot like looking thing in the middle of the headlight? It is only on the passenger side. The tail light have the same spot looking thing.

I'm actually from California now but am originally from Pleasant View up north from Ogden. I'm a member of www.rme4x4.com and they mentioned it to me. It is the one that was on KSL.

Those are great wiring schematics. They should really help with the electrical demons.

Thanks again guys
Title: Re: My cj3A
Post by: F Bill on February 19, 2014, 10:41:36 AM
That's an old school headlight, with a focusing lens in the middle. Prehistoric optics.....but someone building an old school jeep might be interested in it.

I'm surprised you say the tub is rotten.....it looks very nice in pictures.

If you are going thru all the trouble of replacing the tub and rewiring for 12 volt, you will want to go for a new turn signal switch and only two rear lights. 

I'd think long and hard about blasting that good looking jeep apart before I got it drivable and enjoyed it some the way it is.
Here's another post to look at:

http://www.cj3apage.com/cgi-bin/yabb2/YaBB.pl?num=1342019584

Actually reading of ALL the FAQ posts here and on the 2A page should be mandatory for a new jeep owner. Don't forget the left hand studs on some wheels, supposed to be the left wheels but.......occasionally they are on the other side too.
http://www.cj3apage.com/cgi-bin/yabb2/YaBB.pl?num=1371395327
Title: Re: My cj3A
Post by: Medsker51 on February 19, 2014, 12:52:48 PM
It is really clean on the top but the bottom half is gone. Especially around the body mounts. Only half of them are there. I will probably drive it around for a while...at least until I get all of the parts here. The only reason I bought this (other than it is cool) was to have something to work on. I'm retired and extremely bored. I figure putting a new body will take a long time and I don't have the skills to fix all of the rust. I haven't done bodywork for 25 years and even then it was only for a short time. Here is a shot of just one section. It is all like this or worse. This is just the only pic that turned out.

I'm glad you said something about the left hand threads. I just checked and they are left hand. I'm sure I would have broke a stud without the info.
Title: Re: My cj3A
Post by: F Bill on February 19, 2014, 01:44:15 PM
A new hat channel kit, some front floor patching, and a good welder and that can be fixed with a little (well a lot) time. Whatever you do, don't ruin or toss that tub when you get a new one, someone could save that one.

The new tubs are still a bunch of work, and not cheap. But, if you want a fast restoration they are getting much better than they used to be, and you can get a really good looking jeep with one with little bodywork needed.

Title: Re: My cj3A
Post by: Medsker51 on February 19, 2014, 02:22:26 PM
So how would you go about fixing it? Pull the tub, flip it upside down and throw it on some sawhorses? Most of the work is on the bottom so I would want it upside down. Can someone with no experience but a basic mechanical knowledge even do something like this? It seems like one would need a lot more skill to repair the tub as opposed to replacing it. I have all of the tools, welder, etc. I'm actually going to take a welding class this summer which will help.

It looks like the tub is double walled. If you look at the rear of the rust pic I posted you can see the panel pulling away and another panel underneath it. Is it doubled walled or am I seeing something else there?
Title: Re: My cj3A
Post by: 1955CJ-5 on February 19, 2014, 02:43:09 PM
I had no welder and no body experience when I started mine....so yes it can be done.

I think if you browse through the first 8 or 10 threads in the Your Stock Jeep Project forum (this forum) you will see some interesting projects and several different approaches to making repairs...
Title: Re: My cj3A
Post by: Ryan_M on February 19, 2014, 03:26:41 PM
Nice find. My '51 3A is serial # 28433 making it only 63 Jeeps older than yours! Very cool.

Keep us updated on your progress. I'd love to see you tackle that tub. From what I've seen from other projects here it is certainly doable, even for a novice. I'll be diving in to one of my own soon enough.
Title: Re: My cj3A
Post by: F Bill on February 19, 2014, 03:36:07 PM
Quote
So how would you go about fixing it? Pull the tub, flip it upside down and throw it on some sawhorses? Most of the work is on the bottom so I would want it upside down. Can someone with no experience but a basic mechanical knowledge even do something like this? It seems like one would need a lot more skill to repair the tub as opposed to replacing it. I have all of the tools, welder, etc. I'm actually going to take a welding class this summer which will help.

It looks like the tub is double walled. If you look at the rear of the rust pic I posted you can see the panel pulling away and another panel underneath it. Is it doubled walled or am I seeing something else there?

The floor is single thickness, one stamping goes from the riser behind the seats to the dash/firewall panel under the pedals. Most of the time the transmission hump is still good, so you can get away with flat patches, either bought or make your own.  There is a lip along the tub side that spot welds.

Yes, tub off is the way to repair this. I got a tub off this morning in 5 minutes, but it had NO floors whatsoever. Yours will take a bit longer. Hardest part is pulling the steering wheel. Search for threads on that, too as too much force in the wrong spot will ruin your steering shaft and wheel.

Depending on how bad the floor is, you might need to surgically remove all the spot welds that hold the toolbox on the right floor, then repair the floor under it and finally reinstall the toolbox. You may also need a new floor riser or patches in the old one.

Some guys repair the floor, then assemble the hat channels loosely on the frame, and the tub on top of that to make sure everything lines up. Rocketeer I believe was the one who suggested turning the frame upside down as a jig over top of an upturned tub.

Many ways to go to town , and all are right.
Title: Re: My cj3A
Post by: Medsker51 on February 19, 2014, 05:55:37 PM
I read up on the steering wheel and column. They didn't make that easy. I think what I'm going to do is pull it apart. I have to get the tub off whether I replace it or fix it so I will start with that and see how it looks. 

What are people doing with tire replacement? Are you staying with tubes or replacing them?
Title: Re: My cj3A
Post by: garage gnome on February 19, 2014, 06:04:19 PM
I've been using tubes because the stock wheels are not meant to take tubeless. If you want modern tires, you can use radials with tubes.
Title: Re: My cj3A
Post by: Medsker51 on February 27, 2014, 01:12:45 PM
I finally got the tub off of the frame. The frame seems to be in good shape with some mild pitting. I figure if I use a textured coating it should work great.

Title: Re: My cj3A
Post by: Medsker51 on February 27, 2014, 01:31:18 PM
I was trying to decide what to do about the tub of my Willys when I found this guy on Craigslist. I figured I could get it for less than the cost of a tub and have lots of extras. It is pretty much rust free. I flat towed it home and only got a few miles when the rear two tires locked up on me. A fellow Jeeper named Harry (very thankful he pulled over) pulled up to help. It took us a couple of hours of trying to lose break drums, bleed the rear brakes to relieve pressure, and other things to figure it out but came to the conclusion the diff had locked up so we removed the axle shafts and I towed it home. They put a Buick V6 engine which seems to run well except the carb needs cleaned. I've decided to build one Willys to as close to original as I can and then take all of the extra parts and build a rat rod out of them.

I have a couple questions about the new one. The rear tire rack wraps around the corners and hooks on like it is stock. Is it? I have a feeling it isn't. Second, does anyone know of a way to un-yellow the windows?

These are the pics from the listing. I haven't taken any my self. I've already pulled off the monstrosity on the front bumper  :)
Title: Re: My cj3A
Post by: Quebec Jeep on February 27, 2014, 02:00:49 PM
I would save both jeep...
Title: Re: My cj3A
Post by: Medsker51 on February 27, 2014, 09:23:03 PM
I may save both...I figure I'll finish one and then decide what to do with the other.

It took some detective work but finally made out the numbers on the tag "CJ-3A  46572"
Title: Re: My cj3A
Post by: 1955CJ-5 on February 27, 2014, 10:04:03 PM
Both look great and would be excellent candidates for restoration or renovation....

Keep the pictures coming!

The green tub doesn't look too bad from a distance....
Title: Re: My cj3A
Post by: Medsker51 on April 15, 2014, 04:56:28 PM
I've been on vacation the past few weeks but finally had some time to work on it yesterday. I did a few odds and ends and then I pulled the steering gear box, transmission, transfer case, and engine. I went to Harbor Freight and bought a engine hoist and a leveler which was much easier than a chain in the ceiling and a come-along. The steering column is bent pretty bad and I'm sure I will have to replace it. I guess that is what happens when you try to pull the tub off by yourself  :) 
Title: Re: My cj3A
Post by: 1955CJ-5 on April 20, 2014, 08:57:09 PM
There is nothing like have the right tools....

Title: Re: My cj3A
Post by: zooke581 on April 20, 2014, 09:11:25 PM
Man...another clean shop.  Where do you all get those?  Nice work. 
Title: Re: My cj3A
Post by: Medsker51 on April 21, 2014, 11:21:24 AM
 ;D It has taken me thirty years to get a shop like this. Of course a four car garage helps to organize everything. :)
Title: Re: My cj3A
Post by: Medsker51 on April 28, 2014, 09:25:49 PM
So I'm going to sell the top off the red one. It looks like it is in pretty good shape considering it's age. It has one small hole at the top of the driver's door and another small one on the back where the tire carrier wore through. Both are less than an inch long. All the zippers work great and all the snaps work except for one. The one snap has pulled apart but didn't rip the top.

So my question is: what is it worth? I really don't want to ship it so I would have to have a buyer from around here (couple hours north of LA). I wouldn't mind meeting someone part way somewhere though.

Any guesses?

Thanks
Title: Re: My cj3A
Post by: BMIC on April 29, 2014, 10:51:20 AM
Question... Is the tub in the above picture on saw horse's or mounted on a engine stand?
Title: Re: My cj3A
Post by: Medsker51 on April 29, 2014, 11:38:54 AM
It's sitting on saw horses. Just stuck the stand under it to get it out of the way until I needed it.
Title: Re: My cj3A
Post by: Medsker51 on June 26, 2014, 03:45:02 PM
It's been a while since I posted. I've been playing to much and not working on them. I removed the red ones body and pulled the engine. I also included a pic of my "bone yard". I think it looks pretty cool� :)

I'm starting to pull the overdrive and transfer case and have hit a snag. I can't seem to get the snap ring off the rear of the t-case. Any ideas? I can spread it quite a ways but still can't get it to slip over the shaft.

I had forgotten how much fun it is to play with old vehicles. So simple compared to modern vehicles.
Title: Re: My cj3A
Post by: Medsker51 on June 27, 2014, 10:00:22 PM
I have given up on the snap ring and just pulled the tranny and t-case together. The snap ring has to do with the Warn overdrive. I just have a few more things to pull off the frame and then it's off to the sand blaster. I found a local place that will do it for $140. I figure that is worth the money. I may have them do the leaf springs also. I can't wait to get it done so I can start putting things back together. I'm thinking of powder coating the frame. What do you guys think about powder coating? Is it worth it? I've never had anything powder coated before so I don't to much about it. I mean I know the process, but not the durability etc.

Still having fun!  :)
Title: Re: My cj3A
Post by: F Bill on June 28, 2014, 06:55:29 AM
That is a greet price for blasting....if you have any repairs to do to your frame you won't want to powdercoat it until all that is done..

I recently painted a blasted chassis with epoxy primer (material cost was $150) and topcoated with gloss enamel..($120)....It came out very nice, and is repairable if it gets damaged. Powdercoat is tough to repair and tends to trap moisture between the coating and the metal once the film has been broken...In your climate that may not be an issue. In places like the rust belt it is definitely an issue, and many powdercoated things like snowplows and brush guards and trailer hitches actually fail faster due to this moisture trapping effect.

Also if you have any rust pitting or places you will be using a skim coat of filler on to smooth out, you will need to ask your powdercoater what  fillers can be used under powdercoat that will not get destroyed in the baking process. (If you are making a show quality frame)
Title: Re: My cj3A
Post by: macrisel on June 30, 2014, 03:47:41 PM
I agree with Bill on the frame powdercoat.� If your frame flexes very much (as in trail riding, rock climbing or even hitting a speed bump too hard) the powder coat will develop a crack and let in moisture and keep it trapped.� It is also very hard to get a frame clean enough to coat.� When you bake the powdercoat on, it causes the metal to release any oil that may have soaked in over the years......which messes up the powdercoat.�

When I did my resto, I powdercoated my wheels and skid plate on the oil pan.� The oil pan turned out great (go figure), but the wheels did not.� I stripped off the powder coat and recoated them a total of three times......and still had issues.� I finally relented and primed and painted the wheels and moved on.

Powdercoat has its place, but I would probably skip it on the frame.� I used POR 15 on my frame and have had really good luck with it.� Others on here have used Mastercoat and liked it (I didn't know about it until after I used POR 15).� Also, as Bill said a good expoxy primer followed by paint will leave a very nice finish.� Regardless, a great prep will make anything look good and last a long time.

Good luck!
Title: Re: My cj3A
Post by: F Bill on June 30, 2014, 04:34:43 PM
Mark what was the issue with the wheels? I am about to have a set done here in NY....
With blasting I see the seam between the inner and outer pieces trapping sand... if not cleaned out it can be an issue with it showing  sand particles under the paint and rust starting again there. I usually have to clean out that area with a knife and dribble lots of primer in there before painting the rims.
Title: Re: My cj3A
Post by: Medsker51 on June 30, 2014, 04:38:22 PM
Thanks for the info guys. I'll skip the powder coating. I'm not trying to build a show Willys so I think I'll just try por15 or an equivalent on the frame.
Title: Re: My cj3A
Post by: 1955CJ-5 on June 30, 2014, 11:46:45 PM
Look at what Tim did to his frame.....I wish I had known about this stuff...

scroll down a little.....


http://www.cj3apage.com/cgi-bin/yabb2/YaBB.pl?num=1364925701/60
Title: Re: My cj3A
Post by: macrisel on July 01, 2014, 10:24:32 AM
Quote
Mark what was the issue with the wheels? I am about to have a set done here in NY....
With blasting I see the seam between the inner and outer pieces trapping sand... if not cleaned out it can be an issue with it showing� sand particles under the paint and rust starting again there. I usually have to clean out that area with a knife and dribble lots of primer in there before painting the rims.
My wheels seemed to have a rough life.  I didn't have an issue with sand, but I did have an issue with chemicals seeping out when I baked the wheels.  I think it was a combination of brake fluid, oil, dog pee and who knows what else that was etched into the wheels.  I tried pre-baking them several times to get the stuff out, but everytime I thought I had them clean I would prep them and powdercoat them and something else would bubble out and cause the powder to orange peel, fog, or even flake off.  I was just using a coventional oven so maybe I just couldn't get the wheels hot enough.  Like I had said, I also did the oil pan/skid plate and I never had any issues with it.  I also did several other pieces on the jeep and other cars with no issues.......just the wheels.  Go figure.  A professional would probably have better luck than I did.
Title: Re: My cj3A
Post by: 1955CJ-5 on July 01, 2014, 03:02:25 PM
When my 55 was painted so many years ago, the then elderly fellow who painted it said that the jeep "acted as though it had been around sheep".....what he meant was there was oil on the wheels, presumably from the oil in the wool where the animals had rubbed against it, and the paint on the wheels would just fish-eye....
Title: Re: My cj3A
Post by: Medsker51 on October 13, 2014, 11:57:47 AM
I know it's been a while since I updated. I went too fast and forgot to take pictures, at least any cool ones� :)� Here is one of the frame ready to load up and take to the sandblasters. I'm now working on cleaning the front axle. I sure hate cleaning things.� >:(� I'm excited to get the frame back and painted. I figure at that point you start putting things back on it and start moving back up the ladder. I'll try to take more, and better, pictures.
Title: Re: My cj3A
Post by: Medsker51 on January 23, 2015, 05:11:35 PM
It's been a couple of months since I checked in. Lots of playing so I haven't done a whole lot. I've mainly been working on cleaning up the engine so I can paint it. I'm finding I don't like the clean up part of the build. :) I'm sure everyone feels the same way. I walk out into the garage and see the engine on it's stand to clean and my Harley next to it and the Harley wins most of the time  ;D

I hate to use you guys as my personal experts but I have a couple of problems I can't find searching. First, I pulled the distributor and oil pump without really checking how they were installed. I have the engine at TDC but I can't figure out which point on the distributor is the number one spot so I can point the rotor towards it. Second, when I paint the engine do I need to mask off the gasket areas or can I just paint them? I think the gaskets will still seal, but I'm not sure. If I do have to mask them up what is the easiest way to do it?

Thanks for everyone's help!
Title: Re: My cj3A
Post by: athawk11 on January 23, 2015, 09:38:56 PM
Hi Medsker,

The distributor rotor should be pointing at about 5:00 o'clock with the #1 cylinder at TDC.

I masked off the gasket areas.  It's tedious.  Use the gasket as the pattern.  Use a sharpie to draw the shape.  Grab a chair, get comfortable, and start filling in your drawing with tape.

Tim
Title: Re: My cj3A
Post by: 1955CJ-5 on January 23, 2015, 10:09:08 PM
If you have a service manual reprint, the oil pump install is on page 49...

And as Tim said, the rotor should be at about 5 o'clock with #1 at TDC when the distributor is installed....If you get the oil pump in right, there is only one way the distributor will fit as the slot and key are off-set from center...(don't forget the anti-rattle clip if you have one!)

The distributor rotates counter-clockwise, so attach the spark plug leads in the 1-3-4-2 firing order with # 1 at 5 o'clock....

And, if I were to mask off the gasket area (I didn't) I would tape the whole area, then mark it using the gasket as Tim said and then cut and peal away the unneeded tape....
Title: Re: My cj3A
Post by: athawk11 on January 23, 2015, 10:24:50 PM
Quote
And, if I were to mask off the gasket area (I didn't) I would tape the whole area, then mark it using the gasket as Tim said and then cut and peal away the unneeded tape....

That's a far better approach than mine.  I like it.

Tim
Title: Re: My cj3A
Post by: Medsker51 on January 26, 2015, 01:10:34 PM
Thanks for the help guys. So if I understand correctly, I install the oil pump with the slot vertical and then install the distributor into the slot. This puts the number one cylinder at 5 o'clock. Is this correct? I'm at TDC.

Thanks Again!
Title: Re: My cj3A
Post by: 1955CJ-5 on January 26, 2015, 01:33:13 PM
The slot on the oil pump should be at about 11 o'clock, with the larger section upwards towards the head...that should give you a 5 o'clock rotor

The book recommends that you start with the slot at about nine thirty, and as you push it in the gear mesh should rotate it to about 11 o'clock.....
Title: Re: My cj3A
Post by: Medsker51 on January 26, 2015, 03:20:03 PM
Thanks for the info. I was looking at page 42 and it didn't have any info on installation  ;D When you told me page 49 I just assumed that was the page I was on. Teach me to make assumptions  :)
Title: Re: My cj3A
Post by: 1955CJ-5 on January 29, 2015, 09:58:18 PM
Ya know, I often post questions and then find out that the answer is right there in the book...it's OK....there is a lot of info in that manual but not all of it is where you'd expect to find it.....

So, have you got it running?
Title: Re: My cj3A
Post by: Medsker51 on January 29, 2015, 10:30:52 PM
It's still on the engine stand. I haven't started putting the willys together yet. I'm doing the big parts one at a time. So far I've finished the front axle. I'm working on the engine, carburetor and transfer case right now...mostly cleaning. I'm almost ready to paint the engine. I need to pull the cam gear so I can replace the gasket behind the plate and then I should be ready to put it back together and paint it. I'm having trouble finding a puller to get the gear off. None of the pullers I own would work. I ordered one from Amazon that I'm hoping will work but haven't got it yet.
Title: Re: My cj3A
Post by: 1955CJ-5 on January 29, 2015, 10:36:09 PM
You probably already know that the cam gear is a fiber gear, so be careful! The machine shop pulled mine so I have no advice to offer....hope your new puller works..
Title: Re: My cj3A
Post by: Medsker51 on July 22, 2015, 05:31:01 PM
So I know I haven't updated this thread for a while. It seems like you work on it once in a while but things go so slowly you don't take pictures until you hit milestones. I finally got mine on four wheels again. I have mounted the engine in it since the picture was taken and am starting to get the flywheel, clutch and bell housing on when I ran into a problem. My flywheel has four bolts and two dowels. They aren't tapered, they are straight on the sides and don't screw in. It looks like a press fit. So how do I get them in? Do I just snug down the flywheel and then pound them in with a soft mallet until they are flush?

Thanks for any advice.
Title: Re: My cj3A
Post by: athawk11 on July 22, 2015, 09:20:21 PM
I think I understand.  You are replacing the two dowels and the four bolts on the back side of your crankshaft...correct?

I've never needed to replace the dowels, but I believe these should be pressed in with an actual press. 

You might be able to pull them in to position with some washers a nut and an impact wrench, but I just don't know how tight this fit is. 

Tim

Title: Re: My cj3A
Post by: Medsker51 on July 23, 2015, 01:09:38 PM
I'm not replacing them, just trying to install. I'm just not good at explaining  :).  Here is a couple of pics. The first one shows the pins next to the holes they go in. The second pic shows engine lay out. When I removed the flywheel one stayed in the engine side but pulled partially out and the other was in the flywheel side. When I went to install the flywheel one pin went in too far and the other one went in "right". When I pulled the flywheel back off they both only came partially out so I removed them with a brass drift. I think if I press them back in, they still wont insert into the engine side. I own a press so pressing them in isn't a problem. Maybe I'll try to press them into the flywheel and them install it and see what happens.
Title: Re: My cj3A
Post by: Medsker51 on July 23, 2015, 01:46:59 PM
So I was able to hammer the pins in after the flywheel was installed. They went in hard so I think they will stay. Especially since there is only rotational movement so they won't have any forces pushing them in or out.

One more problem down...only a thousand to go  :)
Title: Re: My cj3A
Post by: athawk11 on July 23, 2015, 03:35:44 PM
Ahh. Okay, I get it now. 

Now to offer you my confusion...

Both flywheels I've messed with have similar dowel style pins that center the flywheel, but they are threaded on the clutch side and have a shoulder on the engine side.  They are driven in from the engine side and the shoulder stops them from being pulled out when you tighten the nuts to secure the flywheel.  I don't have a great photo of this, but here you can see the six nuts...

(http://i1195.photobucket.com/albums/aa397/athawk11/athawk11%20Willys%20White/image_zps9a48c98e.jpg)
Title: Re: My cj3A
Post by: Medsker51 on October 08, 2015, 11:52:15 AM
So I got the engine, tranny and transfer case in. I put the front motor mounts on and then when I went to put the tranny mount in they were 1/2" off to the right. I pulled it over with a ratchet strap and got it mounted but I'm wondering if putting a "bind" on the system might be bad for it. The front right motor mounts rubber seems to be twisted a little. Is this something I need to worry about? I measured the frame and it appears to be square. Not sure what else it could be.

Title: Re: My cj3A
Post by: athawk11 on October 08, 2015, 12:07:36 PM
You're probably not hurting anything but the motor mount. There is a slotted hole on the front engine plate. If the motor mounts were tight to the plate when installing the engine, you might be able to loosen the top bolt on the motor mount and relieve the pressure. 

If this doesn't solve the minor twist, you could raise the engine off the frame mounts and elongate the two motor mount holes on the frame.  Maybe use a small circular file or dremmel tool.  It wouldn't take very much. 1/8" would translate into quite a bit of wiggle room once you get back to the tranny mount.

Tim
Title: Re: My cj3A
Post by: Medsker51 on October 11, 2015, 09:51:19 AM
Thanks for the ideas. I will give them a try this week.
Title: Re: My cj3A
Post by: Medsker51 on March 24, 2016, 04:18:19 PM
So question. I looked at the book and it says the transmission and transfer case take 3 1/2 pints together. I see two plugs though...one on the transfer case and one on the transmission. The transfer case one is about an inch lower than the transmission one. Do I just just put oil in the transmission plug since it is higher? Or do I put it in both?

Thanks
Title: Re: My cj3A
Post by: Ryan_M on March 25, 2016, 01:58:59 PM
Quote
So question. I looked at the book and it says the transmission and transfer case take 3 1/2 pints together. I see two plugs though...one on the transfer case and one on the transmission. The transfer case one is about an inch lower than the transmission one. Do I just just put oil in the transmission plug since it is higher? Or do I put it in both?

Thanks


Fill both, drive for a few miles, check both, and top off again if necessary. Fluid will flow between the two but they still need to be filled independently especially when starting from dead empty.

Good to see you're still at it!
Title: Re: My cj3A
Post by: Medsker51 on March 25, 2016, 07:42:14 PM
I'm plugging along on it. I have the engine, tranny and transfer case in. I'm starting on the tub now. Lots to do on it. I finally got everything out of it that the PO put in it. Now I have to start fresh and start adding stock stuff back in.

Thanks for the info on the filling of the t-case and tranny. I'll get that done.
Title: Re: My cj3A
Post by: Medsker51 on March 30, 2016, 01:04:34 PM
So one more question. When I fill the tranny and transfer case do I just put oil in it until it starts coming back out the plug hole like you do on axles? Or do I have to split the 3.5 pint amount between the two?
Title: Re: My cj3A
Post by: Medsker51 on March 30, 2016, 08:23:31 PM
So how do I know how much to put in? Do I fill them up until the fluid is just leaking out the plugs like axles? Do I split the 3.5 pints between them?

Thanks again for everyone's help
Title: Re: My cj3A
Post by: Ryan_M on March 30, 2016, 09:23:01 PM
Quote
So one more question. When I fill the tranny and transfer case do I just put oil in it until it starts coming back out the plug hole like you do on axles?

Yes.
Title: Re: My cj3A
Post by: Medsker51 on March 30, 2016, 09:28:45 PM
Thanks
Title: Re: My cj3A
Post by: RICKG on March 13, 2017, 05:10:04 PM
Here we go.. I promised Medsker I would continue the thread. Jon if you check in from time to time plz say howdy..

When I got back to Idaho with the project the weather just would not cooperate and both jeeps were under tarps in deep snow for the next 5-6 weeks.. >:(
�
Title: Re: My cj3A
Post by: RICKG on March 13, 2017, 05:15:52 PM
Spent the time taking inventory and reconditioning small items like the Kelly locking hubs and the OD.
Title: Re: My cj3A
Post by: RICKG on March 13, 2017, 05:18:52 PM
This weekend I was finally able to get the 3A in the shop with my M38 for company. More to follow when time allows..
Title: Re: My cj3A
Post by: athawk11 on March 14, 2017, 10:27:15 AM
Nice.  Good to see the continuation of this project.

Looks like you got some very nice bits and pieces with the deal.

Tim
Title: Re: My cj3A
Post by: athawk11 on March 14, 2017, 10:29:25 AM
Follow up...

Heat Riser arm position?
Title: Re: My cj3A
Post by: athawk11 on March 14, 2017, 10:31:42 AM
Another follow up...

Cool building! 8-)
Title: Re: My cj3A
Post by: RICKG on March 14, 2017, 10:38:36 AM
Quote
Follow up...

Heat Riser arm position?
Yup, good eye Tim, the arm is simply slid on the shaft, the spring still in a parts bag..
Title: Re: My cj3A
Post by: RICKG on April 18, 2017, 05:21:16 PM
Progress a little at a time. Oil filter and lines plumbed in, carb and fuel pump rebuilt and installed, driveshafts cleaned up and new u-joints installed, exhaust system temp'd in.
Title: Re: My cj3A
Post by: athawk11 on April 18, 2017, 09:05:54 PM
Looking good Muley.  Are you setting up for a chassis run?  I think I read somewhere that you were looking for the basic wiring needed to start the engine.  This might help you...


(http://i1195.photobucket.com/albums/aa397/athawk11/20151202_091837_zps1tyhoa8i.jpg)
Title: Re: My cj3A
Post by: RICKG on April 19, 2017, 09:07:55 AM
I remember seeing that sketch before, thanks Hawky. Not gearing up for a chassis run just yet but am anxious to run up the motor. Need a recore on the raddy before I can do that..
Title: Re: My cj3A
Post by: athawk11 on April 19, 2017, 10:57:38 AM
A re-core.  Ouch. 

Title: Re: My cj3A
Post by: aboyandhisdog on April 19, 2017, 11:10:28 AM
Hey Rick, I just happened to stumble upon your project here.  What if you were to start a separate thread on this project so your stuff would be easy to find and be all in one place?  Just a thought, I need all the help I can get!  ;)
Title: Re: My cj3A
Post by: RICKG on April 19, 2017, 11:52:59 AM
Hi Tom.. when I took over Medskers project he and I talked about continuing this thread. It is, after all, the same jeep just a different monkey bending the wrench. 8-)
Title: Re: My cj3A
Post by: Oilleaker1 on April 19, 2017, 02:47:36 PM
Talked with Muley today. He mentioned going to Sparky's Garage in Dillon for a tuneup.  8-) This 3A found itself a good home. We'll see it in action before too long. Another one to join the group. Oilly
Title: Re: My cj3A
Post by: aboyandhisdog on April 19, 2017, 05:20:46 PM
Ahhhh...got it, Rick.  Missed that it was the same jeep. 
Carry on...
Title: Re: My cj3A
Post by: RICKG on April 21, 2017, 10:08:01 AM
just goofin off.. needed to see a "jeep grin" on the project..
Title: Re: My cj3A
Post by: athawk11 on April 21, 2017, 02:46:49 PM
Will we see this one on the trails sometime this year?  Or maybe next year? 

No pressure. [smiley=happy.gif]
Title: Re: My cj3A
Post by: RICKG on April 21, 2017, 04:55:59 PM
Quote
No pressure. [smiley=happy.gif]

Thanks Hawk-I'm in no hurry, the joy here is the fact that it IS a project-a release from the workday after dealing with clients.. You and I will share some trail dust this year non the less. 
Title: Re: My cj3A
Post by: athawk11 on April 21, 2017, 05:18:59 PM
Ah yes.  There are many like us that need that "project".  It's a great time to contemplate, and to disconnect a bit.

I feel you my friend.

Title: Re: My cj3A
Post by: RICKG on April 24, 2017, 12:19:47 PM
Not the 1st guy to do this I'm sure. Worn clutch rod upgrade. Orig design left much to be desired but I'm sure Mr. Willy didn't count on these little rigs to still be around after 65YR.
Title: Re: My cj3A
Post by: mtnman37879 on April 24, 2017, 12:36:10 PM
Quote
Not the 1st guy to do this I'm sure. Worn clutch rod upgrade. Orig design left much to be desired but I'm sure Mr. Willy didn't count on these little rigs to still be around after 65YR.
You may want to add nuts above the clevises to act as lock nuts.
Title: Re: My cj3A
Post by: RICKG on April 24, 2017, 12:58:16 PM
Quote
Quote
Not the 1st guy to do this I'm sure. Worn clutch rod upgrade. Orig design left much to be desired but I'm sure Mr. Willy didn't count on these little rigs to still be around after 65YR.
You may want to add nuts above the clevises to act as lock nuts.
I considered it but since both ends are rt hand threaded it wont move once installed.
Title: Re: My cj3A
Post by: mtnman37879 on April 25, 2017, 09:03:01 AM
Quote
Quote
Quote
Not the 1st guy to do this I'm sure. Worn clutch rod upgrade. Orig design left much to be desired but I'm sure Mr. Willy didn't count on these little rigs to still be around after 65YR.
You may want to add nuts above the clevises to act as lock nuts.
I considered it but since both ends are rt hand threaded it wont move once installed.
With both ends right hand thread the whole rod can turn. While this won't change the distance between clevises the rod can turn in the threads and could work it's way loose if there was enough slack. If one end was left and the other right it would be sort of locked in place when the clevises were pinned in place, it could still turn given some slack. A lock nut keeps it from moving, guaranteed. 
Title: Re: My cj3A
Post by: athawk11 on April 25, 2017, 11:17:30 AM
Good Mod. 

Muley, I must agree with MtnMan.  While unlikely, it could back out. 

If you can't find a set of nuts, I'll send you a couple. ;D ;D ;)
Title: Re: My cj3A
Post by: RICKG on April 25, 2017, 11:52:20 AM
Quote
Good Mod.�

Muley, I must agree with MtnMan.� While unlikely, it could back out.�

If you can't find a set of nuts, I'll send you a couple. ;D ;D ;)
:o :o :o
Title: Re: My cj3A
Post by: RICKG on April 25, 2017, 08:52:31 PM
OK then.. I had a small stash of 5/16-24 and it's done.. Happy now? I appreciate the offer of your spare pair Sir Hawk but you're still young, save 'em for later..

MtnMan ..I do not know you on a personal level like my pal Hawk, but that means no less. Real Jeep trail time creates lifelong bonds-join us.
Title: Re: My cj3A
Post by: mtnman37879 on April 25, 2017, 10:17:51 PM
Perfect, now it looks professional.
Title: Re: My cj3A
Post by: RICKG on May 11, 2017, 12:09:18 PM
Clutch and brake linkages done. Nice and tight. I purchased the clutch cross shaft specific to the different travel of the cable for the optional 6 spring 9-1/4" Rockford pressure plate
in the jeep.
Title: Re: My cj3A
Post by: athawk11 on May 11, 2017, 11:00:34 PM
Looks sharp!  Are the clutch and brake pedal arms new too?

 I needed a new brake arm.  The reproduction wasn't bent right.  I didn't know this until I installed the tub.  It didn't align with the hole.  I had to take it apart a couple times to heat it and put the right bend in it.  I was not my normal happy-go-lucky self that day. [smiley=angry.gif]
Title: Re: My cj3A
Post by: RICKG on May 12, 2017, 09:32:40 AM
Stock clutch/brake arms Tim. There's the slightest bit of play in the brake arm but i'll live with it.
Title: Re: My cj3A
Post by: 4X4M38 on August 01, 2017, 05:41:55 PM
Hi Rick!
My M38 had the same clevis end clutch rod you made. Some discussion on the MWillys site reveals the Army actually had an MWO to perform exactly the operation on the bent end clutch rods
to solve the problem of the ends getting bent and the clutch out of adjustment.

Until someone surfaced the MWO there was some conjecture it was a Bubba mod.

Take care,
Brian
Title: Re: My cj3A
Post by: RICKG on August 02, 2017, 09:35:07 AM
Hi Brian, good to see you poking around..
Title: Re: My cj3A
Post by: aboyandhisdog on August 02, 2017, 11:34:46 AM
Muley, is the new heavy duty clutch significantly harder to work than the stock 8 1/2" unit?  Also, with the new clevis set-up you made, do you notice any slop in the action?  You do nice work!
Title: Re: My cj3A
Post by: RICKG on August 02, 2017, 01:19:01 PM
Tom, not having driven it I cant say whether or not the HD Rockford is more or less hard to press. As for the linkage there is no slop. I don't remember if I did the linkage upgrade on my M38 or not...I should check and see..
Title: Re: My cj3A
Post by: aboyandhisdog on August 02, 2017, 02:05:32 PM
Muley, you going to FCT?
Title: Re: My cj3A
Post by: RICKG on August 02, 2017, 03:15:40 PM
No can-do this year Tom...
Title: Re: My cj3A
Post by: aboyandhisdog on August 13, 2017, 11:24:49 AM
Muley, can you give me the exact length that the clutch rod should be?� I think I'll make this improvement too and I don't have the OE rod - just an all-thread set up that it came with.� I don't know if it is the correct length.� Thanks!


Also, where did you find your 2 clevis fittings and what size are they?�

Okay, got it all done with 3/8 in clevis yokes from Ace and had to cut the 24tpi threads myself - no fine thread all-thread to be found.  My old rod was 10 5/8 "  oc, but I would still be interested to learn what the oc measurement is of the OE clutch rod.  You must be on a backcountry trip.   8-)
Title: Re: My cj3A
Post by: RICKG on September 07, 2018, 01:19:28 PM
Long time with no updates. Got the inst test panel built and wired the starter test circuit-turned the mighty L134 over by key for the 1st time since I brought the project home winter of '16. After FCT i'll wire ign and charge circuits and see if it'll fire up-stay tuned..
Title: Re: My cj3A
Post by: aboyandhisdog on September 07, 2018, 04:59:18 PM
That's a beautiful thing, Muley!
Title: Re: My cj3A
Post by: Tumbleweed on September 07, 2018, 08:50:46 PM
I like the aluminum radiator. Looking forward to seeing more progress after FCT.

See you in a few days.........
Title: Re: My cj3A
Post by: RICKG on September 07, 2018, 09:11:19 PM
Ya Tom, George, see ya both soon. The 3A project is a mongrel, no pedigree.. No hurry to get it done cuz what then will I do in the shop after work. Someday i'll retire the M38 OD Mule and run the 3A on the trails.
Title: Re: My cj3A
Post by: RICKG on September 09, 2018, 10:24:48 AM
Couldn't wait-yesterday I hooked up the ign circuit, installed a DOT approved fuel cell and fired 'er up and ran it up to operating temp. Its been 2yrs since bringing it home..  Medsker if you're out there yesterday was a good day..
Title: Re: My cj3A
Post by: 64CJ5 on September 09, 2018, 10:50:59 AM
Rick,  You are putting lots of love into that Jeep.  Looks really good.
Title: Re: My cj3A
Post by: squidtone on September 09, 2018, 10:11:54 PM
I love seeing a running Jeep chassis with those kind of fuel cells!
Title: Re: My cj3A
Post by: muley on November 21, 2019, 05:02:23 PM
It's been awhile.. I'm posting from an old computer as I'm being upgraded (if you can call it that). Hawkridge is working with me on the logins.. Thanks Hawk!