My Willys 3A and 3B Community

Your Projects => Your CJ-3A Project => Topic started by: Uncle_Vin on November 25, 2016, 09:49:37 PM

Title: Uncle Vin's 3A
Post by: Uncle_Vin on November 25, 2016, 09:49:37 PM
After years of dreaming about starting my restoration, it's finally happening.  My buddy, Brian Hainer, is doing the restoration. He's capturing the entire resto on video. Here is the link to his You Tube channel.  There are two videos up already. Enjoy - I know I will.  https://youtu.be/1EXMqT2fIoY
Title: Re: Uncle Vin's 3A
Post by: Kirkski on November 26, 2016, 07:09:41 AM
Nice Jeep
Title: Re: Uncle Vin's 3A
Post by: Bob W on November 26, 2016, 08:36:06 AM
Very COOL!!!!
Title: Re: Uncle Vin's 3A
Post by: Uncle_Vin on November 30, 2016, 05:37:40 PM
Here is the latest installment:  https://youtu.be/kJCsOLpY1M8
Title: Re: Uncle Vin's 3A
Post by: Bob W on November 30, 2016, 08:25:44 PM
I subscribed. It is very cool to see all the small details of a CJ-3A!!
Title: Re: Uncle Vin's 3A
Post by: 1955CJ-5 on November 30, 2016, 09:20:30 PM
Yes!

Tell Brian that we really like it!
Title: Re: Uncle Vin's 3A
Post by: aboyandhisdog on November 30, 2016, 09:48:22 PM
Keep 'em coming Vin...this is great viewing!  Thanks.
Title: Re: Uncle Vin's 3A
Post by: athawk11 on December 01, 2016, 01:57:27 PM
Should be a fun series to watch.  I always enjoy learning how skilled folks solve problems.

Hawk
Title: Re: Uncle Vin's 3A
Post by: Uncle_Vin on December 01, 2016, 07:07:21 PM
Here is the next installment fellas:  https://youtu.be/wJEbpavYzhI
Title: Re: Uncle Vin's 3A
Post by: Uncle_Vin on December 01, 2016, 07:08:38 PM
Quote
I subscribed. It is very cool to see all the small details of a CJ-3A!!
What do you think of the engine Bob?  Any idea of what it is?
Title: Re: Uncle Vin's 3A
Post by: athawk11 on December 01, 2016, 08:34:49 PM
It's a mid to late '30s engine.� Maybe from a Willys 77, or Americar?�

It's probably a chain drive.
Title: Re: Uncle Vin's 3A
Post by: Bob W on December 02, 2016, 11:51:54 AM
I agree, looks like a pre-war car engine.
Title: Re: Uncle Vin's 3A
Post by: athawk11 on December 02, 2016, 03:55:17 PM
I have a question Bob.  I've read a little about these pre-war engines.  Horse power output appears to be less (48hp ish) than the war and post war versions.  Do you know what was done to increase the HP on the later versions?  The explanations I've found are kind of vague.

Tim
Title: Re: Uncle Vin's 3A
Post by: Bob W on December 02, 2016, 08:44:56 PM
I'm not real familiar with the early Willys stuff so I will go with Jeep expert Jim Allen's explanation.....
"Roos� reliability benchmark was 100 hours at full power. One of his first tasks was to strap the 48hp engine to a dyno. It lasted 22 hours at 3,400 rpm��nuff said. Roos and his staff set to modernizing the engine, incorporating insert bearings, a fully counterbalanced crankshaft, aluminum pistons, a fully pressurized lubrication system, and a revised valvetrain. In just a few months, the new engine was ready for the dyno. It exceeded 100 hours at over 60 hp at a whopping 4,400 rpm. Success! The new engine was dubbed Go-Devil and first appeared in some of the 1939 Willys cars rated at 61 hp at 3600 rpm. In 1940, when the stylish new Willys 440 (4-cylinder, 1940) models appeared, they were all powered by the Go-Devil, as were the �41 441 and �42 442."
Title: Re: Uncle Vin's 3A
Post by: aboyandhisdog on December 03, 2016, 11:01:00 AM
Quote
It exceeded 100 hours at over 60 hp at a whopping 4,400 rpm.


Yikes!  That would scare the heck out of me.  I have a tach and never exceed 3000rpm (which is around 50 mph as I recall).  Even 3000 sounds like it is winding up pretty good.  Can't imagine going higher.  Bob, are you saying they would keep it at 4400 constant for over 100 hours?  Incredible!
Title: Re: Uncle Vin's 3A
Post by: Bob W on December 04, 2016, 05:52:08 PM
Some of this stuff was destructive testing to failure, not exactly what you would want to do to your own Jeep.
Title: Re: Uncle Vin's 3A
Post by: Uncle_Vin on December 09, 2016, 03:41:43 PM
The next two videos are up. These next two are of the teardown of the T-90 and the D-18.  https://www.youtube.com/channel/UCTHDVml1xugLuj0oi384tEQ
Title: Re: Uncle Vin's 3A
Post by: Bob W on December 09, 2016, 04:31:04 PM
It is great to see a true Willys expert and master mechanic/body-man at work!!! There aren't many of these guys around.
Title: Re: Uncle Vin's 3A
Post by: Uncle_Vin on December 14, 2016, 09:08:30 PM
There are more videos up.
Title: Re: Uncle Vin's 3A
Post by: Uncle_Vin on January 03, 2017, 05:20:05 PM
There are a bunch more videos up.
Title: Re: Uncle Vin's 3A
Post by: Uncle_Vin on February 10, 2017, 02:55:57 PM
Lot's of new videos are up.  Good stuff.  Here is the link to the latest (https://www.youtube.com/watch?v=ih1qw8B7yeY&feature=em-uploademail)