My Willys 3A and 3B Community

Your Projects => Your CJ-3A Project => Topic started by: BJ on November 03, 2014, 02:59:02 PM

Title: BJ's Willys
Post by: BJ on November 03, 2014, 02:59:02 PM
This is my project.

Just a quick back story on it.
The Jeep was donated to My high school in 1994. The instructor funded the project and me and a couple of the other shop kids took on the project. I have no pictures but it had a locked up motor and had been left in a mud hole on a hunting camp in Mississippi. We did the best we could getting it to run and when it was running the shop instructor took it home to play with.
Two years after I graduated he died of cancer. We the students helped out the wife during and after his death. The jeep ended up in storage in a garage with the trailer. Sometime in 2006 she called me and asked if I wanted the jeep. She could no longer keep it.

The CMA56 is what the instructor "Mr. Paterson" came up with.
He went to Columbia military Academy and graduated in 1956.

This is when I loaded it up and brought it home. 
(http://i3.photobucket.com/albums/y77/DirtyRat/Gatlinburg%2008/100_3561.jpg) (http://s3.photobucket.com/user/DirtyRat/media/Gatlinburg%2008/100_3561.jpg.html)

(http://i3.photobucket.com/albums/y77/DirtyRat/Gatlinburg%2008/100_3559.jpg) (http://s3.photobucket.com/user/DirtyRat/media/Gatlinburg%2008/100_3559.jpg.html)
Title: Re: BJ's Willys
Post by: BJ on November 03, 2014, 03:01:20 PM
I put a new fuel system and it and was able to drive it around.

(http://i3.photobucket.com/albums/y77/DirtyRat/Jeep/101_4172.jpg) (http://s3.photobucket.com/user/DirtyRat/media/Jeep/101_4172.jpg.html)
Title: Re: BJ's Willys
Post by: BJ on November 03, 2014, 06:26:12 PM
The front axle was a little rough so I decided to tackle this task. This was the first axle I had ever taken apart but was sure that I could handle it.

(http://i3.photobucket.com/albums/y77/DirtyRat/Jeep/RightFront.jpg) (http://s3.photobucket.com/user/DirtyRat/media/Jeep/RightFront.jpg.html)

There looked like there had been a little water in the front at some point and the outer pinion bearing was shot so I started tearing into it.

(http://i3.photobucket.com/albums/y77/DirtyRat/Jeep/FrontDifCover.jpg) (http://s3.photobucket.com/user/DirtyRat/media/Jeep/FrontDifCover.jpg.html)

The axles didn't look to bad so I re used them.

(http://i3.photobucket.com/albums/y77/DirtyRat/Jeep/RightFrontAxle.jpg) (http://s3.photobucket.com/user/DirtyRat/media/Jeep/RightFrontAxle.jpg.html)

Title: Re: BJ's Willys
Post by: BJ on November 03, 2014, 06:37:12 PM
After a little work and a lot of head scretching I got it all back together.

(http://i3.photobucket.com/albums/y77/DirtyRat/Jeep/HubsComplete.jpg) (http://s3.photobucket.com/user/DirtyRat/media/Jeep/HubsComplete.jpg.html)
Title: Re: BJ's Willys
Post by: BJ on November 03, 2014, 06:52:41 PM
I the mid 90's parts where a bit hard to find. This radiator was the closest year we could find. It was for a CJ5. We used some creative piping and a funny shroud to make the water go the proper direction.
(http://i3.photobucket.com/albums/y77/DirtyRat/Jeep/radiator3.jpg) (http://s3.photobucket.com/user/DirtyRat/media/Jeep/radiator3.jpg.html)

(http://i3.photobucket.com/albums/y77/DirtyRat/Jeep/radiator1.jpg) (http://s3.photobucket.com/user/DirtyRat/media/Jeep/radiator1.jpg.html)
Title: Re: BJ's Willys
Post by: BJ on November 03, 2014, 06:57:38 PM
After 10 years sitting still it had a few leaks so it was time to pull it out and put in something that fits properly.

Title: Re: BJ's Willys
Post by: 1955CJ-5 on November 03, 2014, 09:26:23 PM
Great background story, and it's very cool that you were part of it.

The work you are doing looks great also.....keep the updates and photos coming...

Randy
Title: Re: BJ's Willys
Post by: BJ on November 16, 2014, 08:40:12 PM
The transmition was having a few problems so it's time for a rebuild so I thought I would start with the transfer case.

The first order of business is to clean it up and see what I have to work with.

(http://i3.photobucket.com/albums/y77/DirtyRat/Jeep/69337554-0C22-451C-B318-363A835440C8_zps2izeqfic.jpg) (http://s3.photobucket.com/user/DirtyRat/media/Jeep/69337554-0C22-451C-B318-363A835440C8_zps2izeqfic.jpg.html)
Title: Re: BJ's Willys
Post by: BJ on November 16, 2014, 08:42:00 PM
After a good cleaning it was time to strip it down. This went fairly smoothly and head to surprises.
(http://i3.photobucket.com/albums/y77/DirtyRat/Jeep/A48F17A9-22CC-4E07-99A3-9B712FD8D3EE_zpsjysguezf.jpg) (http://s3.photobucket.com/user/DirtyRat/media/Jeep/A48F17A9-22CC-4E07-99A3-9B712FD8D3EE_zpsjysguezf.jpg.html)
Title: Re: BJ's Willys
Post by: BJ on November 16, 2014, 08:43:53 PM
(http://i3.photobucket.com/albums/y77/DirtyRat/Jeep/1F912C2E-5DAB-4D6C-B1DD-2B0B0456891C_zpspxxjdhsm.jpg) (http://s3.photobucket.com/user/DirtyRat/media/Jeep/1F912C2E-5DAB-4D6C-B1DD-2B0B0456891C_zpspxxjdhsm.jpg.html)

(http://i3.photobucket.com/albums/y77/DirtyRat/Jeep/40D6547A-8059-4AE9-92F9-06E92D395B15_zpsuwpygtcc.jpg) (http://s3.photobucket.com/user/DirtyRat/media/Jeep/40D6547A-8059-4AE9-92F9-06E92D395B15_zpsuwpygtcc.jpg.html)
Title: Re: BJ's Willys
Post by: BJ on November 16, 2014, 08:45:49 PM
This is not looking good.

(http://i3.photobucket.com/albums/y77/DirtyRat/Jeep/96CD685F-0CE1-49E7-A033-70EE47EAA315_zpsfe9dwguk.jpg) (http://s3.photobucket.com/user/DirtyRat/media/Jeep/96CD685F-0CE1-49E7-A033-70EE47EAA315_zpsfe9dwguk.jpg.html)


(http://i3.photobucket.com/albums/y77/DirtyRat/Jeep/DE66DC93-8C70-46D6-9228-85960D75BC20_zpsr0xtmudf.jpg) (http://s3.photobucket.com/user/DirtyRat/media/Jeep/DE66DC93-8C70-46D6-9228-85960D75BC20_zpsr0xtmudf.jpg.html)
Title: Re: BJ's Willys
Post by: BJ on November 16, 2014, 08:48:34 PM
Looks like this has been there for a while.
(http://i3.photobucket.com/albums/y77/DirtyRat/Jeep/14214F4F-BD0C-4541-9EB4-318E76C785E6_zpsvv29lkot.jpg) (http://s3.photobucket.com/user/DirtyRat/media/Jeep/14214F4F-BD0C-4541-9EB4-318E76C785E6_zpsvv29lkot.jpg.html)
Title: Re: BJ's Willys
Post by: BJ on November 16, 2014, 08:50:23 PM
The rest of the gears seemed to clean up nicely.

(http://i3.photobucket.com/albums/y77/DirtyRat/Jeep/49D901E2-1269-4768-8EF7-50535C7C052E_zpsyu01si51.jpg) (http://s3.photobucket.com/user/DirtyRat/media/Jeep/49D901E2-1269-4768-8EF7-50535C7C052E_zpsyu01si51.jpg.html)
Title: Re: BJ's Willys
Post by: 1955CJ-5 on November 16, 2014, 08:50:49 PM
I think those 1 1/8" intermediate shafts and bearings go bad on a regular basis.....When they finally went to 1 1/4" shafts and the loose roller bearings there was quite an improvement.....
Title: Re: BJ's Willys
Post by: 1955CJ-5 on November 16, 2014, 08:51:53 PM
Quote
Looks like this has been there for a while.

Like maybe from the factory!
Title: Re: BJ's Willys
Post by: BJ on November 17, 2014, 03:27:11 AM
Quote
Quote
Looks like this has been there for a while.

Like maybe from the factory!

That's what I was thinking.
Title: Re: BJ's Willys
Post by: BJ on December 15, 2014, 02:41:50 PM
I was able to find some time to jump back into this project for a bit. I got the tranny and transfer case housing both cleaned and painted. I also gave the gears a good inspection and started putting things back together.

(http://i3.photobucket.com/albums/y77/DirtyRat/Jeep/569B20AD-FF2F-4AE5-8E76-4C2DD087E103_zpsuvgj37ou.jpg) (http://s3.photobucket.com/user/DirtyRat/media/Jeep/569B20AD-FF2F-4AE5-8E76-4C2DD087E103_zpsuvgj37ou.jpg.html)
Title: Re: BJ's Willys
Post by: 1955CJ-5 on December 15, 2014, 08:25:54 PM
Does your intermediate gear from the transfer case have any markings on it? I have one with a small maltese cross and another with a W with a circle around it....Just curious, I have no idea what they mean other than maybe manufacturers marks...

They are fun to work on when they are clean!
Title: Re: BJ's Willys
Post by: BJ on December 17, 2014, 09:23:00 PM
I don't rember any makings but I'll check closer when I get back out to the shop.
Title: Re: BJ's Willys
Post by: BJ on December 25, 2014, 06:25:46 PM
(http://i3.photobucket.com/albums/y77/DirtyRat/Jeep/F5B55B96-424B-4D5A-9A62-6793B6568A9B_zpspcwojeh2.jpg) (http://s3.photobucket.com/user/DirtyRat/media/Jeep/F5B55B96-424B-4D5A-9A62-6793B6568A9B_zpspcwojeh2.jpg.html)
Title: Re: BJ's Willys
Post by: 1955CJ-5 on December 25, 2014, 09:20:12 PM
So I just had a moment of enlightenment.....

It seems all the D-18 parts use the number 18 as the first number in identifying the individual parts....my original intermediate shaft has the same number stamped on it...

Thanks for the picture!
Title: Re: BJ's Willys
Post by: BJ on March 02, 2015, 01:05:34 PM
The tranny and transfer case are now complete. They are painted and put together ready to go back in. I took my time with it and I am sure that it's going to work like it should. I'll put up a picture of the assembly when I rember to take one.


I had a leak on the rear main seal of the motor so there is no better time than now to take care of that. I pulled the pan after ordering a new seal kit from Walcks. I was able to get the new seal in with no huge problems but now I am left with a question. There is two rubber pins that go in on eather side of the rear main cap. The new ones that where in the kit are to long. Do I cut them flush or mash them in with the oil pan. I measured the hole that they go in and it looks to be about 1/2" longer



(http://i3.photobucket.com/albums/y77/DirtyRat/Jeep/6A41F0D9-CEB8-4C3B-9395-DB6D56A3BF3A_zpsoahsjsma.jpg) (http://s3.photobucket.com/user/DirtyRat/media/Jeep/6A41F0D9-CEB8-4C3B-9395-DB6D56A3BF3A_zpsoahsjsma.jpg.html)
Title: Re: BJ's Willys
Post by: athawk11 on March 02, 2015, 04:31:20 PM
BJ,
You will want to leave them long.  I believe you want approximately 1/4" sticking above the cap. They get seated and squished when the oil pan is re-installed. 

It looks like one of your crank to flywheel bolts was removed.  I know you probably already put it back in, but if not, there is no better time than now. ;)

Tim



Tim
Title: Re: BJ's Willys
Post by: BJ on March 03, 2015, 10:47:59 AM
Yup.
Title: Re: BJ's Willys
Post by: BJ on March 24, 2015, 04:58:55 AM
Ok. This passed weekend I completed the tranny install and started putting the drive line back together. I found the pinion loose on the rear axle so I yanked it iut and took it apart.


(http://i3.photobucket.com/albums/y77/DirtyRat/Jeep/B70E6519-460B-4204-A1AE-7225E6DF84BA_zpshfarqica.jpg) (http://s3.photobucket.com/user/DirtyRat/media/Jeep/B70E6519-460B-4204-A1AE-7225E6DF84BA_zpshfarqica.jpg.html)

Everything was loose inside. It looked like the carrier bearings had spun a little as well.
Title: Re: BJ's Willys
Post by: BJ on March 24, 2015, 05:05:48 AM
Everything else looked good

(http://i3.photobucket.com/albums/y77/DirtyRat/Jeep/C4C1D769-C277-4A33-84C4-FA5BEBA0B4AD_zpso44c1fk6.jpg) (http://s3.photobucket.com/user/DirtyRat/media/Jeep/C4C1D769-C277-4A33-84C4-FA5BEBA0B4AD_zpso44c1fk6.jpg.html)

(http://i3.photobucket.com/albums/y77/DirtyRat/Jeep/F968B63A-68B4-406D-B479-133FF1E5CA91_zpsst1meavn.jpg) (http://s3.photobucket.com/user/DirtyRat/media/Jeep/F968B63A-68B4-406D-B479-133FF1E5CA91_zpsst1meavn.jpg.html)

So after cleaning everything up I started to put it back together.

The ring and pinion had been ridding a little low on the tooth but the gears where still in very good shape so I re used them. I did install all new bearings and gave it a proper gear set up. Then after tackling the outer bearings it was time to re install the axle.

I am super happy with how it all turned out. It all works so very well. It drives and shifts like it never has before.

Title: Re: BJ's Willys
Post by: BJ on March 24, 2015, 05:10:56 AM
Next on the list if things to do is the starter. The starter is not wanting to engage properly all of the time. Sometimes you push the starter pedal and it just grinds. If you wiggle it around and push it you get a perfect start. I think the end of the starter is warn out.
Title: Re: BJ's Willys
Post by: Ryan_289 on March 24, 2015, 09:48:40 AM
I made the mistake of cutting the rubber dowels for the rear main flush once.  I didnt wait around to see if they leaked, I just installed new ones. It still sucked to redo it again!
Title: Re: BJ's Willys
Post by: Ryan_289 on March 24, 2015, 09:50:56 AM
Quote
Next on the list if things to do is the starter. The starter is not wanting to engage properly all of the time. Sometimes you push the starter pedal and it just grinds. If you wiggle it around and push it you get a perfect start. I think the end of the starter is warn out.


You might just need a new bendix.  Not to hard to replace.
Title: Re: BJ's Willys
Post by: JeepFever on March 24, 2015, 10:54:05 PM
Quote
I am super happy with how it all turned out. It all works so very well. It drives and shifts like it never has before.

Nice work!  . . . it is so satisfying to make things better.
Title: Re: BJ's Willys
Post by: BJ on March 26, 2015, 08:10:08 PM
I took it out to the race this weekend. (I help run an off-road racing series) so fare it is working better than it ever has.

This picture makes me reailize that the Willys Jeep is the original side by side.  ;D

(http://i3.photobucket.com/albums/y77/DirtyRat/Jeep/E0155AA3-8D8A-411B-B19D-10AB79816B16_zpsc8ykrzuf.jpg) (http://s3.photobucket.com/user/DirtyRat/media/Jeep/E0155AA3-8D8A-411B-B19D-10AB79816B16_zpsc8ykrzuf.jpg.html)
Title: Re: BJ's Willys
Post by: BJ on March 27, 2015, 07:30:53 AM
Next I am going to start on some of the body work but for this weekend it's my transportation around the race track.



(http://i3.photobucket.com/albums/y77/DirtyRat/Jeep/D5435CD4-493F-43A6-A904-977C25A166A2_zpsb3suwa3m.jpg) (http://s3.photobucket.com/user/DirtyRat/media/Jeep/D5435CD4-493F-43A6-A904-977C25A166A2_zpsb3suwa3m.jpg.html)





Title: Re: BJ's Willys
Post by: BJ on March 27, 2015, 07:31:45 AM
It almost looks out of place next to these off-road monsters.

(http://i3.photobucket.com/albums/y77/DirtyRat/Jeep/454C40FA-2D96-4722-A9A7-7F6F155A3D76_zpsl5trsrgg.jpg)[/URL

 (http://s3.photobucket.com/user/DirtyRat/media/Jeep/454C40FA-2D96-4722-A9A7-7F6F155A3D76_zpsl5trsrgg.jpg.html)
Title: Re: BJ's Willys
Post by: bretto on March 27, 2015, 07:35:31 AM
Those are great pics.
Those youngins better respect their elder. :)
Title: Re: BJ's Willys
Post by: BJ on March 30, 2015, 05:47:16 AM
I made a linkage adjustment to the starter and it worked fine all weekend. Every once and a while it would grind but it worked a lot better. I'll get it a new starter gear just to be on the safe side.

Test results from this weekend reveal that it's having trouble starting when cold. It would have fire and gas but not want to start up. Two mornings I had to give it a small sniff of carburetor cleaner to fire up. After that it would run fine all day. I'm thinking a new set of plugs should help out.

Also it was spilling oil out of the air breather after some of the rougher roads. Is this normal?

All in all everything went very well. It looks like I will be ready to start on some of the body work after a few changes.

Title: Re: BJ's Willys
Post by: corpsman on April 10, 2015, 01:44:05 AM
looks like you do good work.  it all looks great.