My Willys 3A and 3B Community
Your Projects => Your CJ-3A Project => Topic started by: zooke581 on September 19, 2013, 07:27:24 PM
-
Well picked up this last week. Got there a little late as the owner parted out the starter and carb and 16 inch wheels.
The first time I saw it he had backed into it and took out the grill, radiator, alternator and generator bracket and mangled the front fenders.
I was contemplating starting it when a fellow Jeeper stopped by and we got to looking at it. He noticed the tag on the block as I did and said this is a Supersonic. I wiped off all the buildup on the head and sure enough it was.
My starter wouldn't fit as the bolt holes are too small. So I put the word out and a fellow 3Aer came through with an NOS one.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20130916_181542_zps7bf15b53.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20130918_185426_zps73bbacfd.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20130918_185406_zpsde8534ec.jpg)
-
Motor is free and not stuck. Four wheel drive has been added over the 2 wheel. So far just need a carb. Hope to get a compression reading. I could use the carb of my 2A for now. Tub is in really good shape. It did come with a 46 2A grill and I have a 3A radiator in my 2A.
Hmmmmmm. What to do, what to do.
Building a 42 GPW Salad Jeep right now. But this would be fun.
-
Nice find. Body look in good shape.
Add it on your next project list!
-
Old locked up front brakes are a PITA >:( Need to get the front loosened so I can move the Jeep over to the shop.
-
Got them freed. :) That just took me back 27 years. 8-)
-
Going to use this old DJ for my military clone so I can take my time with the real GPW stuff on my modded CJ2A frame.
Got a little done on it today. Took the front wheels off to remove the brake shoes that were binding. Removed the front fenders and Bubba'd radiator brackets. Cleaned up the bed and mocked up the GPW grille to see what it looked like.
Starter still is not here. USPS is very happy to give an early delivery time so you will go with them. They actually deliver it about 5 days later. Hope that will be Monday. Until then I can do other things.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20130928_164842_zps628b8159.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20130928_181428_zps9d975931.jpg)
-
Well, today was a good day, outside of the fact I broke my left foot big toe at work. Thumbs Down Gives a whole new meaning to big toe.
Starter arrived today. NOS Autolite 6V from Ryan_M. Thanks. Put the starter on and cranked the engine for the first time. Did a compression test and 95 on the back two and 105 on the front two. Used the 12v battery to do this.
Put on the carb from my other Jeep I had rebuilt and put in some gas. Jumped the starter with the positive off the coil - nothing.Unhappy
Cleaned the plugs (did this before I put them back in and tried the first start). Checked the points in the distributor and no spark. Cleaned points and now has spark. Tried again and starter whines. Put in 6V starter and tried again. Motor comes to life. Big smile
Ran for few seconds and sounded good. All in all a good investment. Looks like I will have a Jeep to use while I am doing my Military Clone with real Military parts.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20130930_194459_zpsa9e0c2a8.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20130930_194408_zpsb7a27a01.jpg)
-
Video of the DJ3A running after I added a few more things from the 46 2A (radiator, generator, fan belt).
https://www.facebook.com/photo.php?v=3430309773896&set=vb.1754910983&type=2&theater
-
Sounds good! That's at least 2 Willys this week that we know of that have returned from the brink of extinction. I love the oil filter set-up. Have you made any attempt to drive it yet?
-
Not yet. Want to clean the rear mounted gas tank first, then fill it and I will try to drive it then. Won't be till Sunday probably as this Friday I am picking up a GPW block, grill and assorted GPW parts then on to the East Coast Flat Fenders Swap Meet on Saturday. Hope to trade some stuff and sell some. ;D
Awesome you got yours running too. And Military to boot. :)
-
Actually got the DJ to move under it's own power. Shifted through all gears nicely. Now I need to do the brakes and set up a fuel tank system that will work well. All I have is a CJ2A tank that would need modified as there is now side panel opening for the fill neck on a DJ. It is a rear tank mount system.
-
Well, between Ron Fizpatrick's and Debella's (the most affordable from each {and both guys were great and helpful on the phone}), I got the brake parts I needed to put this project safely on the road. Wheel cylinders, hard and soft brake lines, brake lining and rivets, gaskets and lock nuts (as the PO used a drift to get the old ones off). The springs, shackles axles and all look in great shape. Need one set of new 6.00 x 16 tires for the roller and I'll be good to go.
Going to take the body off and repair bad spots. While off I will replace the trans cross member as it has the trans too high up and off to the side. Must have used the DJ two wheel drive trans cross member when they put in the 4 wheel drive.
-
Did a little work on the Jeep today and boy am I sore. Got the body off and the underside is in pretty good shape. Some patching, replacing hat channels and straightening it should be good. It had be completely undercoated at one time is why it is in such good shape.
The transmission hump will need to be adjusted to fit the T90 as the DJ wasn't four wheel drive.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20131019_125647_zpsb03f7526.jpg)
-
Needed to do some adjustments once the body was off. The PO did some strange things in fitting the four wheel drive to the DJ. The trans and transfer cases mounted on the an M38 cross member were too far to the passenger side. and too high up. The clutch control tube had an extension to welded to it to reach the frame rail and also modified clutch control frame bracket. I used ones from my stash of parts to correct this. CJ2A frame cross member brackets were added (DJ3A ones were removed).
Exhaust will need to be rerouted as when the rear suspension moved it hit the exhaust and collapsed the right rear brake hard line. And I found out my CJ2A master cylinder will not match up to the bolt holes for the DJ3A.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20131019_125616_zps2fbba4b7.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20131019_125606_zpsee763e2d.jpg)
-
Well the idea was to get this one on the road quickly. Just do a brake job, correct the mounting of the transmission and transfer case, repair some bad linkages, minor body repairs and have a Jeep to drive while I restored the GPW/2A the right way.
Things just don't seem to work out that way. When you go so far you see another are that needs fixed while things are apart and it just snowballs from there.
Little more work done today with the biggest thing, getting the Jeep in the shop. Had to kick some of the bikes out to the curb to do so though. Poor bikes.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20131026_173715_zpsf2c76a71.jpg)
Working on the brakes (and a little bit more). It really looks good inside. Have new brake lines, master cylinder, brake cylinders and shoes.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20131026_193218_zpsf114548e.jpg)
-
Working on the brakes was fun. Now I need a few more parts to finish. Adjusting nuts, the felt seal, proper master cylinder as the GPW/2A one is not right and will not fit the holes and support bracket at all. The hardest part is not going overboard on making the parts look good as I just want this as a runner and not a ground up resto. (So....hard....must....make....myself....stop).
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20131027_175217_zpsb7044a78.jpg)
I thought these tags were only on the Military axles.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20131027_175320_zps7b160eac.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20131027_175151_zps4265ba61.jpg)
-
Took off the transmission shift cover to have a look see. As I noted before it moved under it own power in the drive way forward and reverse.
There is slight surface rust. In the picture it looks far worse than what it really is. I will clean this rust off and fill it back up with the proper gear lube. The transfer was also drained and the lube came out clean with no moisture at all. So if feel confident on that as well.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20131027_182515_zps5713e238.jpg)
-
Here is the difference between the 2A and 3A master cylinders. I did fit the 2A double brake line mount instead of the single 3A one as I have brake lines from a 2A fitted because of the 2A axles.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20131031_191442_zpsee8cf320.jpg)
-
Here is the difference between the 2A and 3A master cylinders.� I did fit the 2A double brake line mount instead of the single 3A one as I have brake lines from a 2A fitted because of the 2A axles.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20131031_191442_zpsee8cf320.jpg)
This would make a good picture for our FAQ section. I know when you order a Crown master cylinder from some places they ask you what the hole spacing is.. Does anyone know off hand when the change was made? Even when I was ordering one for my GPW the guy at the store asked me if I knew the bolt hole spacing.
-
Without going into the books I believe the change occurred on the late CJ-2As at the same time as the frame was improved.
-
My 3A (early '49) had the Rzeppa tags on it. Also had the gear ratio tags. I'm quite happy that they were still there!
-Paul
-
Little more done today. Got the knuckles completely done with new lube, seals and gaskets. Riveted new linings on the brakes and installed them. Next step is to install the brake drums and lockouts.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20131116_205826_zpsb2576e50.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20131116_205842_zps2b62bc44.jpg)
-
It looks good...
Where did you find the linings and rivets, and how did you fasten the rivets? Just by hand?
Did the Rzeppa joints go back in?
-
I got the linings and rivets from Debella and the Rzeppa joints were in perfect shape and reinstalled.� All the bushings inside as well as bearings were in great shape.� They were cleaned packed and reinstalled as well.
And yes, the rivets were installed by hand.
-
Nice work Zooke. It's always seems to be an internal fight as to how far to go with a repair/restore. I'm with you there.
I'm working on the axles and brakes right now too. It's fun to see others working on the same stage.
Tim
-
One wheel down and three to go. Got the drum on with freshly packed bearings and serviced lockout. Plus a better picture of the linings installed with new rivets.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20131117_192543_zps82271360.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20131117_192522_zps0cf0677a.jpg)
-
Worked on the drivers side front axle tonight. So another one down. Took a little more time on this one and now will have a do-over on the passenger side front axle. Never did one before and want to make sure the other side is as good as this one.
Cleaned and repacked the wheel bearings as they were in great shape. The races on the wheel were great as well.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20131119_190613_zpsd1ef84ad.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20131119_190858_zps4d7d20d1.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20131119_190643_zps30436e77.jpg)
-
Installed the wheel with new nuts as the old ones were butchered with a drift to get them off and back on.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20131119_195256_zps26d079df.jpg)
Next I added the lower portion of the lockout attaced the axle and nut and put a new cotter pin in. Of course the lockout were completely taken apart, cleaned, inspected and lubricated.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20131119_200918_zps97f1cb7d.jpg)
Top half of lockout added, torqued down and tabs bent over. The tie-rod in the picture is being replaced with a proper length one that does not need to be bent to get proper toe setup.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20131119_201855_zps75d2bb9d.jpg)
-
Ordered a Made in USA drum puller last Friday and was surprised to see it in the mailbox when I got home. So...after feeding the dogs and puppies I hightailed it out to the garage to see how well it worked. Just like magic. So now to get the rear R&R the rear plates and put the new brake shoes and cylinders on.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20131202_182403_zps8c40addc.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20131202_183145_zps989682bb.jpg)
The old axle seals were the felt type and were well worn causing axle grease to contaminate the brake shoes and generally gum up the rear brakes alltogether.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20131202_183213_zps36362c67.jpg)
-
Got a little more work done this weekend. Left rear brake backing plate, bolts, brake shoes, wheel cylinder, seals and gaskets installed. Also got the brake drum on as well but did not take a picture of that.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20131215_171449_zps94621b19.jpg)
-
Checked out the rear differential. Looks like new. No noticeable wear. So I cleaned op the housing, cover and bolts, installed a new gasket and fill with fresh gear oil.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20131209_192314_zpsf7efdd79.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20131211_062329_zpsb05cab28.jpg)
-
Now what's left is to do the right rear wheel and I can adjust the shoes, fill the brake master, bleed the lines and see if I did all this right. ;)
-
Did a little more work today. Got the final brake backing plate and brakes done. Now to fit the final brake line up front and adjust the shoes and fill and bleed the system.
Below are the photos of the last wheel brake assembly. Bolts and shims in place.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20131222_140431_zpsc677b541.jpg)
Bearing retainer and brake backing plate in place.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20131222_140558_zps28241ef7.jpg)
Gasket, drum seal and gasket in place.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20131222_140816_zpsffc50cd5.jpg)
Splash shield installed and bolt torqued to 30 ftlbs. Bearing pumpes with grease to make sure it was filling. Shoes installed along with new wheel cylinder.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20131222_150200_zps1a1b0344.jpg)
-
Got a lot more done today. Put the final line on the brakes and filed the brake master cylinder and bled the lines. Quite a chore. Tightening all the connections over again after finding myraid leaks. Done and done now. Best done with the tub off and real easy. Cleaned the frame and all part that will show so I can paint with Eastwood rust encapsulator and then OD paint.
Worked on the tie rod that was wrong and now I have to get a new end. Hope they have one at Advance Auto tomorrow.
Pulled off the diff cover on the front and cleaned. Put a new seal on and it leaks. Will take it off tomorrow and put some sealant on it for a better seal.
-
Why are you painting it OD green?
-
Got the paint and like the color.
-
Flu has really got hold on me. Started on the way home day after Christmas. Still want to get things done on the jeep as I don't go to work till next year. Wink
Got the frame cleaned of loose rust and dirt and coated with Eastwood rust encapsulator on the parts that will show as this jeep is a quickie to use till I restore the MB/GPW right.
Frame cleaned and ready for rust encapsulator.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20131229_181412_zps436aff04.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20131229_181433_zps1697f2e1.jpg)
Coated with Eastwood rust encapsulator.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20131229_193805_zpsf36c6c0a.jpg)
-
OD is on both sides now. Going to let the fog settle and check for light spots and touch up. Still have to do the middle of the axles but need to get more paint for that.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20131230_142823_zps87a894bf.jpg)
-
Hey Zook,
I don't know my DJs at all. The frame appears to have some 2A and 3A characteristics. Tranny/TC crossmember looks like a 2A, but the rest of the frame looks 3A. Am I seeing that right?
Nice work.
Tim
-
The DJ I got uses a 3A frame and rear.� The owner had it modified for 4 wheel by adding the front axle and trans and transfer.� I left it that way and am using the DJ3A body it came� with with slight mods.
Yes the cross member is 2A the PO had bubba'd up the 3A one so bad I couldn't use it and used a 2A one I had.
-
Replaced the wrong drivers side tie rod that was bent to work with the proper one. Replaced on tie rod end with a good one and put new dust boots on all. Tie rods were all tight and are now lubed as well.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140111_111432_zpscef5a062.jpg)
-
Straightend the front bumper a little and welded up the crack on the bumper and frame horn.� I also filled in some extra holes in the bumper and filled the license plate slots as well.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140111_111608_zps29ea0371.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140111_124252_zps1afc7573.jpg)
-
The bumper, tie rods and front axle center are now coated in Eastwood Rust Encapsultor and ready for OD paint when it gets here on Tuesday. Got to old radiator out and ready for the proper one. Had to weld on new tabs as they were in a different spot for the other radiator.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140111_180028_zpsf568100a.jpg)
-
Treated myself to a birthday present of working in the shop on my Jeep. Will post up pics tomorrow of what I got done.
-
Happy birthday!
-
Thanks 1955CJ5.
-
Probably spent nearaly eight hours today correcting things that needed fixed. Engine was too low in front, too far to the passenger side, and trans and transfer were too far to the drivers side. Also the drag link was bent all wrong and didn't get full lock to lock on the steering. Drag link has been rebuilt.
Now all that is corrected and the axles have been cleaned and coated to Eastwood rust incapsulator for painting in OD tomorrow. Not to mention pulled a muscle real bad in my calf by trying to use it as a jack instead of a real jack. Keep forgetting that I am not 20 anymore.
-
Painted the axles and linkages OD. Fixed a brake fluid leak on one of the S lines.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140119_115211_zps2ec986ed.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140119_122200_zps1f1df41d.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140119_163630_zps60fa4a47.jpg)
-
Shocks painted and installed. Just inexpensive Monroe shocks from Advance Auto. Get a Veterans Discount.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140119_163610_zps2103f842.jpg)
Front axle and linkages painted.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140119_163727_zps0d1e197a.jpg)
-
Didn't pull the transmission or transfer, just pulled off the covers to see condition. Transfer case inside look like new. Just resealed the rear cover and bottom cover and filled with GL1. The lower cover had OD on and could be from an M38. There was no tag on the transfer but there was a stamped number on the transmission.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140123_145838_zpsf5c406cd.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140123_160006_zpsbb7b1701.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140123_171635_zps5ee22d9c.jpg)
-
Finished brushing the transmission gears and flushing the cases. Then filled with GL1 and installed the shifter with a new gasket.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140123_171609_zps5548c2de.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140123_185652_zps2c94b511.jpg)
-
Good idea. I almost filled up with�fluid before putting the shift tower back on my recent project. I went the conventional route and used the fill plug instead which is always a messy hassle. The way you went at least gives you ones easy fill.
-
The DJ3A had brackets bolted to the rear frame rails and a front bumper was used for a rear. That was removed and an upper bracket was installed as here the DJ had none as there was a rear mounted gas tank instead.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140125_125556_zps0bfeed75.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140125_153135_zps77a82110.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140125_153202_zpse1a4fc6f.jpg)
-
Last night removed the oil pan as it had a lot of weepage around the gasket. Upon removing and cleaning it was dimpled bad around the bolt holes so I tapped them back flat with a hammer and installed new gasket. Inside the motor looked real good and that was a relief.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140126_153038_zpsf111bf64.jpg)
Also the oil canister was changed for a later, what I have been told, CJ style oil filter setup. I am going to leave that but use a Purolator filter rather than Fram. Bad things from Fram in my Motorcycle days.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140126_165138_zps4c48f925.jpg)
-
Tried fixing the radiator myself, no go. So took it in for repair, just the basics, $77. On the chassis now with new hoses and most hooked up for a fill tomorrow and a basic running to see if all is okay.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140204_203632_zps543906e9.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140204_203701_zpscbdf0f86.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140204_203612_zpsb10a627e.jpg)
-
It looks great..nothing like a fresh radiator :D� �Good luck on the test run...that anti-freeze can be slippery stuff....my machinist recommended straight water for the first run and leak check....
I've never seen an oil filter like that on a jeep! Was that stock on a DJ?
Now I noticed your previous post....my 55 CJ5 still has the canister type...
-
I've never seen an oil filter like that on a jeep! Was that stock on a DJ?
Now I noticed your previous post....my 55 CJ5 still has the canister type...
What I found out is that the setup is from a Studebaker and was a common use for the Jeep and also drag racers. Took a little to find out about it and what filters were good. Don't like Fram and it had a NAPA 1050 and cross referenced to a Purolator. It is a special filter because of it's positon.
-
Filters that are installed like that have a valve or flap that keep them from draining when the engine is shut down....as least you have a real oil filter! Is it full flow or plumbed like the original?
-
It's plumbed like the original and is called a bypass filter for the upside down application.
-
Got 98 percent of everything working on the chassis today and took it for a spin. It was fun trying to throttle it without a gas pedal and just trying to push the linkage with my foot. The rest wasn't too bad. Need to adjust the carb as it has bad spot about 1/3 throttle and wants to stall. Adjusting the brakes yesterday was fun.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/chassistest_zps95388dac.jpg)
https://www.youtube.com/watch?v=rNOSe6h1ldk
-
Excellent! That smile says it all. Lots of fun!
-
Looks great, sounds great! Congratulations!
They sure are fun to drive like that.
And sitting directly on the fuel tank?
You are fearless!
-
Thanks guys.� Don't have muffler on yet. Just exhaust pipe out to rear. Was fun today.� Now on to the body.
-
If any more guys post pictures of driving their chassis we will have to have a 3a page chassis race at the next meet.
-
Took it in the backfield in 2nd gear. I is not comfortable. :o ;)
-
A few more things installed today. New radiator cap vs old one. New generator bushings vs only old one.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140216_113827_zpse4a20543.jpg)
Pintle reinforcement plate vs didn't have one forgot to order when I got the bumper and brace.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140216_122149_zpsd5e9f733.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140216_124338_zps0010007a.jpg)
-
Now that the chassis is pretty much done, time to work on the tub. At the start I had posted a pic of it off without cleaning. Here it is again.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20131019_125647_zpsb03f7526.jpg)
And here it is after I cleaned off the undercoating still sticking to the underside. It's in pretty good shape.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140223_165910_zpscf9d934b.jpg)
-
The top side. Lots of extra holes to fill, some minor rust, and cutouts that need replaced. It's getting a GPW dash as the the DJ3A one was pretty shot.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140223_170043_zpsa8a7b0af.jpg)
-
That tub looks pretty good!
-
That tub looks pretty good!
Quite happy with the condition after all those years. Can't wait to get started. :)
-
Still have to move some things around to get the tub in the shop where the chassis is so did a few other things on the chassis.
I installed a new carb gasket and diffuser. The old gasket was actually several thin ones and they leaked air. This really helped out and correcting a few things with the carb.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140222_161836_zps2fcd122c.jpg)
I had installed the new rusty muffler from Debella but did not have the tailpiece till today. Now this on the the Jeep is now quiet. Sort of a high mud muffler like on the Military.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140224_191240_zpsed2e3b53.jpg)
-
I like the rusty muffler. I saw those on Debella's site awhile back. Too funny. Good deal though.
-
Zooke,
I enjoyed the chassis trip.
The tub looks quite good. I've not seen the extra hat channel support under the passenger floor. Is that a DJ thing?
Tim
-
Zooke,
I enjoyed the chassis trip.
The tub looks quite good.� I've not seen the extra hat channel support under the passenger floor.� Is that a DJ thing?
Tim
Thanks. Yes it is a DJ thing. It did not have the stock rear mount gas tank but I believe the extra hat channel had something to do with that. Plus it did not have the extra frame V brace that other CJs had because of the tank and they may also have been a reason for the extra hat channel.
-
And now the next stage begins. The chassis and body have switched place in the garage. Going to replace only those needed parts on the body and not going to remove all the dings and dents. Just want a good solid body with no rust through.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140302_172119_zpsdb5630de.jpg)
-
It looks like you have a good starting point.....is that a dash with a glove box opening?
-
It looks like you have a good starting point.....is that a dash with a glove box opening?
Yes, It's a GPW dash. Needs straightened and some rusted parts repaired, then installed.
-
Did a little prep work on the body to get to the floor repairs. Took the hat channels off of the passenger side. It also needs work on the wheel well behind the seat and the riser corner. The trans hump needs a little repair as well. Now this DJ body had no wood in the hat channels, it had u shaped supports welded to one side the hat channel to keep from collapsing during bolt down of the tub.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140309_201927_zps85c7a429.jpg)
-
Cut the passenger side of the floor out too many hole to fill along with the rotted areas. This was the best bet. It will also allow me to replace a section of the riser that was bad. The riser had pulled away from the rear quarter panel as well as the wheel well that is quite mangled that will need replaced as well. It will also allow me to keep the dimple on the stock floor.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140311_200514_zps74b481d8.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140311_200549_zps8216f959.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140311_200532_zpsa5f80f53.jpg)
-
Now that the chassis is pretty much done, time to work on the tub.� At the start I had posted a pic of it off without cleaning.� Here it is again.
Thanks for posting these pictures.� IF I had not saw them TODAY I can guarantee you I would have left that extra piece of hat channel on the passenger side off of mine!!!
-
Well got a lot of work to do and not enough time to do it. Took out the old passenger riser section and front of the fender well along with the hat channel panel support. Bent a new riser section and welded it in place.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140315_174028_zpsbf4ad9e2.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140315_181521_zpse53828ad.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140315_193352_zps118f260c.jpg)
-
Looks good!
-
There is nothing like new steel!....
-
Zooke,
That's a tough piece to make. Nice work.
Tim
-
Zooke,
That's a tough piece to make.� Nice work.
Tim
�
Now I get to do the other side as well :'( ;D
-
Made a new front fender well panel and welded it in. Now that was a first for me.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140316_131535_zpsccf92be4.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/e6cf2dcb-7aa3-4de5-b68f-bd508e62f46a_zpsa64d3b03.jpg)
-
Hey it looks great....it's kinda fun making panels....not too hard...and what an improvement! Very rewarding...
-
After all that work on the front fender well, I wasn't happy with the gauge of steel. It was only 24ga and needed to be thicker so I got some 20ga and refromed it. I removed the 24ga and installed and welded up the new 20ga. Much happier and it is stronger.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140319_204317_zps788ed4f6.jpg)
-
The thicker steel is a little harder to 'work', but long term, you will be happier you made that decision. I say, the heavier, the better.
Tim
-
Got the driver side floor pan in place. Some minor trimming and it's ready for welding in tonight.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140321_063145_zpsae402263.jpg)
-
Tonight the panel has been trimmed and welded in place on the side panel and riser. I used special clamps to align the floor gaps evenly and tacked those in. Now off to the house to do the dishes as per my text msg from the Wife. :o
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140321_205343_zps4c6c72f2.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140321_205211_zps3110bb49.jpg)
-
I have seen those clamps advertised...but too late for my project...they seem like an excellent tool for a great result...
-
I got them at Harbor Freight.� Good price and they really work great.
-
I think I saw them or something similar at Eastwood...
Either way it looks like they work great...I bought a bunch of vice-grip type clamps, but these would have been better...
-
The floor panel is in and welds are ground down (not perfect but good enough).
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140322_201534_zps882b6e2c.jpg)
Set the old hat channels on to mark where the new ones go. I had some made in 8' lengths and made them to fit from there.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140322_132152_zps74928545.jpg)
New hat channels being welded in place. I use a metal dowl in place of the u-strap where the body to frame bolts go.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140322_201446_zps11bdc228.jpg)
I also welded up some of the many holes. (more than the whole US Deficite) and took care of some the rust in the body step.
-
Nice! Looks very solid...
-
Finished up the hat channels on the passenger side.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140323_124821_zpse92bbf27.jpg)
Where the body mount bolts went I put in a dowl instead of the u-shaped metal piece the factory used. There was no wood in these hat channels.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140323_122606_zpsa4433d2c.jpg)
-
On the drivers side I took more metal out of the floor as I did not have the factory indent that I wanted to keep. I also took a lot off the side panel as the step was pretty rusted and I am putting tool indents in.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140323_191523_zps51e9e4a0.jpg)
-
Looking good!
-
Thanks guys for watching. Got to get it mostly done by a parade at the Veterans Care Center in Salem, VA and a few parades after through D-Day.
-
Got the drivers side riser off tonight. Trying to a do a little each night. So much bondo as the PO used this rather than to straighten out the body. I am rectifying this situation as I replace pieces.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140324_201154_zpsee40588b.jpg)
-
Real nice I am enjoying the progress
-
It's interesting to see just how those come out...mine was totally rusted where it met the floor and the bed...and about everywhere else...
They were pretty generous with those spot welds....
-
Worked on the tool indents tonight. I have the front half and installed it. I will have to make the rear with some good tips from athawk11.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140327_191506_zps62ebdd95.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140327_193112_zpsec0b1783.jpg)
-
Made the drivers side floor riser and welded it in.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140329_131358_zpsd8551aad.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140329_143147_zpsc681ff5f.jpg)
-
Got the drivers side floor panel cut and fitted. Ready for welding tomorrow.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140329_202716_zps34a96e9b.jpg)
-
I can't believe how useful those little butt-joint clamps are.....
Looks great.....
-
Got more done today. Drivers side floor panel installed and some hat channels. Made a mistake on this but it is easily corrected. See if anyone can find it. That is why the pic shows both sides.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140330_194736_zpsaafa8fb7.jpg)
-
Lookin good. I don't see any mistake?
-
I can't see one either. Can you give us a hint?
Tim
-
Holes and capture nuts in hat channel.....
-
PapaC is pretty much on the money. The wider hat channel on the bottom is where the mistake is.
-
PapaC is pretty much on the money.� The wider hat channel on the bottom is where the mistake is.
The different offsets in the holes was the ONLY thing I could see that looked suspicious. The rest of the work is awesome and I AM just a little bit jealous of your skills, especially the welding!!!
-
I had clamped the passenger bottom hat channel on and it popped off.� I picked it up reset it and welded it one.� Only after I welded the second piece on and rechecked for the next hat channel piece did I notice the hole and captive nut was not where it was supposed to be.� I had picked it up flipped. Oh well :'( easy fix) and on with the show.
-
Worked on repairing the drivers side step. It was rusted about the hat channel and where it attached to the body. I cut a new piece and welded it to the step and then fitted it to the body. Welding to commence tomorrow. Still have a small insert section to weld in yet. Then on to finish the tool indents.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140331_194438_zps4ad0772b.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140401_201517_zps731537a1.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140401_201546_zps6b7318ae.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140401_203455_zps73a40d79.jpg)
-
Got the last of the hat channels for the floors in. I added the small section to the drivers side that was in the passenger side on the DJ3A. Adds a lot of extra support to the floors.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140405_090604_zpsa0a5fe24.jpg)
-
Worked on the last piece of the hat channel for the transmission hump. Took that part off of my part jeep and fitted and welded it in.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140405_105910_zps970f9902.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140405_110752_zps3a36b13d.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140405_112236_zps06688d0a.jpg)
-
Next I had to cut a patch for the hole the PO had put in the transmission tunnel for a bubba'd brake parking lever. The panel had to have a small arc hand formed to fit before welding. Panel clamps were used to hold into place for the welding process.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140405_173404_zps311ee33d.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140405_190908_zpscd77537c.jpg)
-
Worked on the transmission tunnel today. It was different than a CJ2A and 3A as the DJ was not 4x4. Then when the PO added 4x4 he cut it up real bad. How it looked when I started today.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140406_110442_zps081ff3f4.jpg)
The tunnel from my CJ2A parts tub to be used.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140406_110522_zpsf4613a04.jpg)
Set in place and marked for cutout and fitment.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140406_142505_zpsb2a67a81.jpg)
Welded in place. Still need to do a small section to the right and the upper left where the steering column and brake pedal go.
-
Welded in place.� Still need to do a small section to the right and the upper left where the steering column and brake pedal go.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140406_162416_zpsd8b46689.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140406_171326_zpsdac17931.jpg)
-
Looks like it's really starting to come together now. Nice work.
Tim
-
Got the steering column and brake pedal holes panel cut and fitted for welding.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140408_193902_zps6bfda3cf.jpg)
Patch panel welded and ground down.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140408_202137_zpsee2a76b1.jpg)
-
Really nice, this thread and those like it are why this Forum is the highlight of my day!
-
Thanks all for watching. Watching others posts like mine is what gave me incentive and ideas on how to do my build. ;)
-
Today played with the 42 GPW dash I am going to use. It is from a Non-Script GPW tub I am going to restore. The cowl was pretty bad from a good hit in the front end. I have a replacement cowl with a good dash and glove box so this rusted dash became a donor for my "Clone" project. You can see the work I need to do on the bottom edge (rusted) and the glove box opening (rusted). After a good straightening it doesn't look too bad does it?
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140409_183636_zpsb9f1322c.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140409_183707_zps15b5f6d6.jpg)
And a test fit.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140409_200942_zps47d07cc0.jpg)
-
That tub is looking great! I envy your welding skills..
It will be handy to have a glove box...I think it looks fine....
-
Nothing ever seems to go as fast as you first think. And...Dad's words seem to keep echoing on this project, "Anything worth doing is worth doing right". So with that out of the way:
More work on the dash. Notice the exception wear on the bottom edge of the dash and around the glove box door. This was removed and a new piece from the DJ3A dash (with enough more gauges in it than the space shuttle) was used for repairs.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140412_093727_zps497981a7.jpg)
New piece from DJ dash set and ready for welding.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140412_110413_zps5ba0c302.jpg)
Welded and cleaned up. What I hadn't noticed is the indent for the glove box door is still done even though there was no longer a glove box. Still need to do the edging in the glove box for the door seal.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140412_122652_zps41920271.jpg)
-
Now on to making the glove box seal trim. I cut some 20 ga sheet stock and put it on a piece of wood I cut to make the bends on each side.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140412_143344_zps5e6d93d9.jpg)
Next it was set in place and the corners were bent. It was fitted and then the cutout for the door spring was cut in. Now clamped down for welding.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140412_151654_zps258c328c.jpg)
Welded in place and final forming done. Now on to the upper part. This was a lot more work then I anticipated.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140412_163115_zps8339aa67.jpg)
-
Forming the upper seal trim for the glove box. I clamped it to a milled 2 x 4 and proceeded to tap down the edge to look like the original.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140412_175129_zps62d31b40.jpg)
The final piece ready to be bent in installed.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140412_175940_zpscda03e7d.jpg)
Installed and ready for the dash to be put in the tub.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140412_195045_zps5fa5c16c.jpg)
This was more work than I had imagined. But now I don't need to go back and try to fit it while in the jeep.
-
That's it. I give up. I'm sending all my rusty parts to zooke581.
Awesome save on a junk part! Nobody can complain about you using that dash on a non stock jeep,
I've always wanted to take all my junkers and build something unusual out of it but I think you'd do better with the junkpile than I. ;D
-
F Bill, send all your junk parts this way. Be glad to have them. :) 8-)
-
WHOA This is too much fun to watch!
-
Well...the dash is in. I don't think it will be coming out anytime soon. I did a lot of little things like filling hole of which there are many. Welding and grinding, welding and grinding, welding and grinding...
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140414_063556_zpsda9e8288.jpg)
-
Tonight I worked and the rear of the tub for a change. I am putting in military type signal holes.
They will be a little more outboard unlike the original ones. I did not want to cut into the bed to put them in the proper position. This will work out fine and get rid of the many hole the PO put in for too many lights on the rear and the rust.
Set up for placement is the section I made. The same is going to go on the other side as well.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140414_202943_zps99afda78.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140414_203013_zps12ec6050.jpg)
-
That's a nice circular cut. How did you do that?
Tim
-
I actually had those laser cut for me. I tried one and didn't look how I wanted it to.
-
Winter decided to come back for about three days so no work done tonight. About 20 degrees. My family has got to quit sending their weather from Wyoming this way.
-
Got a little further on the rear light panels. I made the light brackets and welded them in. I then fit the new panel and get it ready for welding tomorrow.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140416_190929_zpsca487f48.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140416_193550_zps5bae0bb4.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140416_200002_zpsbabdb67d.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140416_200031_zpsd4050ffb.jpg)
-
Reworked the first rear light panel I put in. Tank of gas for the welder was bad. It wasn't fun but it is done. Amazing what good gas can do. Then on to the other side. Lots of rot there. Removed it and made up the new panel for install.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140419_122507_zps4f9f98b5.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140419_135533_zps2c5815ff.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140419_152830_zps7afaea63.jpg)
-
Not the best picture but here it is with the recessed military light panels.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140419_202840_zps2e975735.jpg)
-
Since I was already on the back panel I continued to do some more changes. I took out the two center braces that were there for the rear center mounted tire bracket. I then put in a hat channel like the military jeeps. I also put a couple of dowels for support where the lower military tire bracket will mount. I will put in the triangular braces in tomorrow.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140419_184715_zpsea8c5912.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140419_202517_zps38126c69.jpg)
-
Made some braces on for the back panel that help support the extra weight like tire and gerry can. It's nice to have both a GPW and MB tub to get measurements off of to do this.
The braces on the GPW.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140420_115859_zps66256046.jpg)
The brace I made.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140420_154030_zps3b477308.jpg)
The brace now welded in place. I did this instead of bolting it like the GPW as if I remember correctly the MBs are. My MB tub had the panel cut out for a tailgate so I couldn't check.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140420_122230_zpsc4b1240b.jpg)
-
Sanded the back panel after I filled a million holes. The bondo was thick. Now I see why. Looks like a Army ball peen hammer brigade attacked the rear of my jeep. No hope in me getting all these hammered out.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140420_175129_zpse96026ea.jpg)
I measured my GPW and drilled out the holes for the tire carrier and mounted it. I also made a template of the Gerry Can support panel, made one and clamped it in place. With the tire and gerry can it will cover up much of the rear panel. So...should I skim coat with bondo to get most of the dimples out or just leave it?
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140420_192951_zps2f94a73d.jpg)
-
My vote...
A little war torn is probably a good thing, but...
A flat chunk of steel bar stock...around 4" x 2" x 5/8" is my favorite dolly for hammering away at a Willys. You would be surprised at how smooth you can get that panel. Add in a little heat shrinking then a little more hammer/dolly work. Smooth with a light coat of filler...just to even out the surfaces hiding behind your hat channels, then call it good.
You're doing such a nice job on the repairs. This surface will be one of the most seen on your Willys. Smooth it to at least the level you will smooth out the sides. Otherwise, I think you might regret not cleaning it up a bit.
My humble opinion only.
Tim
-
Did a small final patch on the transmission tunnel.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140421_191618_zps42941acd.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140421_194202_zps57284009.jpg)
Also did a little work on the back panel. Didn't do what I wanted it to and don't want to spend too much time so I will skim coat it with bondo. And on to the tool indents. That is going to take a bit of work and the final small patch forward of the tool indents to finish yet too.
This jeep was supposed to be my quick runner but it got more involved than expected (don't they normally go that way?). It is my test mule and learning process for the GPW/MB that is next on the plate.
-
This evening I worked on the tool indents. I tried a couple of ways that were just not going to work and then I fell upon this way that was much easier. Wished I'd have thought of it a few pieces of sheet metal earlier.
Marking out the replacement sheet for the indent cutouts. Indents were already made and bent for insert and welding.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140424_155614_zps1f5d03a0.jpg)
Axe indent inserted and welded in.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140424_162027_zps681c317f.jpg)
Both axe and shovel indent welds ground down ans smoothed out.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140424_175513_zps0d2ce1ea.jpg)
-
Finished panel next to a bad panel off one of my Military tubs.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140424_175612_zps8650d6a2.jpg)
Installed and finished. I think it'll pass.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140424_205507_zps97a0f58b.jpg)
-
Well, don't that just beat all!
This thing is a work of art.....
-
Thanks!
-
I've been trying to resist the "Wow that looks great" comments throughout this whole thread. I can't help myself here after seeing that installed panel.
WOW! THAT LOOKS GREAT!!
-
Thanks! I wished my first panels looked as good as this does. But...this tub is a learning experience for me and the GPW tub will get that experience.
-
Today I did some blasting on the tub. Now that's a lot of tedious work. I did this to find the holes and areas that need to be welded before I do the body prep before paint.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140426_190450_zps1fd49851.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140426_210131_zps42a0d888.jpg)
-
Still working on it daily. Filling a multitude of hole in the tub from a rollbar to fender skirts to who know what else. I have never seen so many holes in a Jeep or any other vehicle for that matter. Tedious work this is.
-
Patched some more holes today and still a lot left to go. Also out some bolts in four holes that are in the exact spot I need them for the rear seat retaining hooks found on the MB and GPW. How they are on the DJ/Surrey tub I do not know.
The Seat retaining hook on the GPW.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140429_193136_zps49841159.jpg)
Holes in my DJ/Surrey tub.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140429_193112_zps98a9a2d0.jpg)
Piece cut out, bolts welded to plate and plate welded back in.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140429_194531_zps39b233c5.jpg)
Ground down and ready for paint when I get to that part.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140429_195325_zps56a2aee2.jpg)
-
My grinding never came out that nice.....is there a secret, besides skill and experience? ;)
-
My grinding never came out that nice.....is there a secret, besides skill and experience? ;)
Must be the old school word working skills my Dad taught me from his journeyman carpentry in Germany. ;)
-
Been working on the most nearly every day. Most filling holes of which there were far to many to even count. I didn't post this as it would have just been too boring as it was for me to do.
I did mount rear seat pivot bracket and support. I bolted them in instead of riveting them in as the factory did. But I did weld the support at the bottom as factory did.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140504_120213_zpsa217dc13.jpg)
The seat was one I purchased for my GPW but I found out is was for an M38 so this actually worked out in my favor as I am making a DJ into a Military Clone.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140504_120428_zps506399c6.jpg)
-
And now actually a few holes I did fill. Hopefully the last ones today. First the grill.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140504_162456_zps8a87ddab.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140504_162727_zps38522781.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140504_162502_zps91ac15a6.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140504_165245_zps2eaa9aa9.jpg)
-
The last of two patch panels I had to do today. This is filling the drain hole of the DJ/CJ tub and making it look like a Military Tub.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140504_170217_zps8a424d40.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140504_184251_zpsb1f40123.jpg)
-
Sealed all the seams, welds and welded holes with seam sealer. Then after it had dried for a couple of days I am starting the Red Oxide primer in preparation for the OD paint. Then I can set it on the frame and work on the sides and inside of the tub.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140506_153836_zps9d9ed618.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140506_153854_zps74c7a455.jpg)
-
That Willys is really coming together nicely. You should feel very proud.
I know you have a GPW waiting in the wings. Are you going to keep both? Are you going to jump into that project as soon as this one is finished? Or...take a break?
Tim
-
That Willys is really coming together nicely.� You should feel very proud.
I know you have a GPW waiting in the wings.� Are you going to keep both?� Are you going to jump into that project as soon as this one is finished?� Or...take a break?
Tim
Thanks. Probably going to sell this one when I am done with the GPW, but that is not happening any time soon. Not going to rush the GPW. But will start as soon as this one is done.
-
More tub work done today. Finished up a few weld spots that needed attention and painted the underside so it can be mounted on the chassis hopefully tomorrow.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140510_190157_zpsda0b08f4.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140510_190235_zpsadeb04b6.jpg)
-
Shot a coat of OD on the tool indents to see how they would look. Still will need a little touch up after the tub is on. And got a coat of primer on the grill. It is a little pitted but not going to change that.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140510_194628_zps32254860.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140510_201002_zps78ec17db.jpg)
-
Well today was the day to put the body on. I thought of many ways short of lifting with what I had and nothing was going to work. We don't know anyone close and it was Mother's Day. Julie said she would come out and try to lift it on.
We picked it up but she couldn't lift it up high enough being a few inches shorter than me. Wink So she suggested steps to walk it up. That worked perfect. One it went and real easy I might add. Thanks Sweetheart!
On one body mount hole was off by about 3/8 of an inch. Drilled it out to the mounting plate. All bolted down now.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140511_150851_zpsbdad4a2b.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140511_150916_zps7ff413e5.jpg)
-
Looks ready enough for an ice cream run!
-
Back in the good side of the garage. Grill painted today and on. Supposed to get rain for the rest of the week. So body work this week in preparation for the weekends good weather.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140511_194035_zps939d1bc4.jpg)
-
Can't wait...you are going to be "done" before you know it.....
Does that spin-on filter clear the hood? There probably is a short version that would fit too....
-
The filter setup was on it when I got it. It is a Studebaker filter setup. This was used on drag cars a lot. It clears the hood very easily.
-
Worked some more on the fender today. After I cut out the brace I marked and cut out the cancer. I cut some new pieces, tack welded them in and did the final weld and cutting. I will have to fashion a bracket from salvaged pieces as I only have the new one for the battery side fender.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140515_190256_zps66f5bae1.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140515_200706_zps8d506168.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140515_210230_zps633ed5a8.jpg)
-
Looking good Zooke. I remember doing that same patch. Darn wood filler!!
Tim
-
Looking good Zooke.� I remember doing that same patch.� Darn wood filler!!
Tim
Surprisingly this was the DJ fender and there was no wood filler. Rusted anyway. There was no wood filler on the hat channels either. Now I have to make up a brace unless I can take on off one of my other fenders. I'm learning on this welding stuff. I get better each weld. Just have to get this one done in two weeks. Next project will be better and slower.
-
When I repaired my fenders which were pretty much rusted just like yours, F_Bill recommended that I bolt the fender to the tub and grill, then bolt the brace to the frame, and then weld the brace to the fender, insuring alignment later on.....
You may have already done this, but I found it to be excellent advice..
-
Thanks HG.
The fender is on adjusted now with the new top. Set the MB hood on to see how it looks with both fenders. The passenger side fender new a couple of adjustments and one weld. Then back off to prime and paint.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140521_210255_zpsb35d1afc.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140521_210238_zps5199fda9.jpg)
-
Prepped, primed and painted the fenders. They are by no means perfect. They are servicable. Part of the Jeep are really good and other parts and servicable. These can be done at a later date as will other things. I need it done quickly. So servicable will be the order of the day every day till June 6th. Then little touchups and changes can be done while I restore the real GPW/MB.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140523_133713_zps15e8ea46.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140523_142014_zpsccc5c539.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140523_204638_zpsbb81ae06.jpg)
-
Now that I am back from DC and very wore out. Keep forgetting I am not 18 anymore. Did some work on the Jeep.
I looked at all the Jeeps in the DC parade and they did not pay the attention I did while doing mine. So with that enlightenment I am going to go a simpler route and skip a few things.
I filled the ball peen hammer dents in the back panel but left the waves. I want this to look like a motorpool restoration. Light repairs and repaint with some dents still intact. Like a combat repaint. I painted the top of the engine hood as well. I mounted the tire rack and gerry can holder with the support piece I made. The recessed light holes are looking good.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140527_211821_zpsf05b05df.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140527_222729_zps9107e76d.jpg)
-
You'll be on the road before you know it....but you have probably already been secretly driving it around.....
-
Actually been pushing it around. Need it done before 6 June. or close. So a few things will be skipped so I can have at the National D-Day Memorial for the 70th Anniversary of D-Day.
-
Just did work in the garage today. No painting. It was raining. So I attached some items like the axe holders, welded on the axe sheath, gerry can strap and mounted the fenders as well.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140529_200743_zps8bb4c122.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140529_200805_zps934b98ac.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140529_200657_zps60e02903.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140529_210906_zpsaa1d4931.jpg)
-
Have I seen that Foster's can before, or is that a new one?
-
You have to be excited about your progress. Looks like you're going to make your time line.
Good luck.
Tim
-
Started out at 9AM like this.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140531_112952_zpsb912b9b1.jpg)
Went and worked on the seams of my welds in the floor so they looked half way decent. Cleans off loose rust and sanded for primer. It is not a perfect job. The jeep is not supposed to be but it is supposed to be rust free and structurally solid. Primer is on.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140531_150435_zps7efa4b03.jpg)
Lusterless Olive Drab is on.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140531_160721_zps9cf35930.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140531_160734_zps9fd87c88.jpg)
-
Got the hood on, the hood catches, windshield catches, the blackout light and few assorted items.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140531_182139_zps53b88807.jpg)
Bumperetts installed and lights set in place for installation tomorrow.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140531_214503_zps954974f9.jpg)
-
Today was an interesting day. Put the flip up light housing in. Bolted in the rear taillights. Installed and hooked up the speedo, oil pressure gauge, temp gauge and just set the others in. Permanently installed the steering column cover after paint. Painted the windshield frame and installed it. It fits like crap. It touches the body metal to metal and is bowed so the seal does not seal. The clasps for the windshield were way off but worked. It's on and functional. Painted the inner windshield and installed it along with the kickout brackets. Set the rear seat in. Then I worked on the tank. Had to make adjustments for a military fill under the seat. Removed the side fill and put a patch on it. Then welded the filler on the top. Checked for leaks and all was good on the second pass. Then I went to clean it up for painting and under the paint were about 50 rust holes. Three hours shot. Tomorrow will repair the tank. It looked good.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140601_210251_zpsa7af9bf9.jpg)
-
Have this waiting on me from my good friend Britt Taylor Collins. A very rare Airborne Dump Trailer. Completely original with all the correct data plates. What an awesome friend.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/dumptrailer_zps300a0722.jpg)
-
Present from my cousin Joe was waiting on the porch when I got home. Guess what it is.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140604_191451_zps6f5827f3.jpg)
-
Love seeing people nearing the end of the project give me hope that the jeep will drive again. ;D
-
June 6, was the day I was working for so hard to get my Jeep to the National D-Day Memorial for the veterans that served. The closer I got to the memorial the better the Jeep was received with me in my 101st WWII Uniform. That is when the emotions of what this event is in history hit me and I nearly had to pull over. The sacrifice of so many young people was so enormous. Tears welled up behind my sunglasses. As I pulled into the Memorial the reception of what the jeep represents in our quest to help free the world in such desperate times is still so evident in our younger generation. While I worked so hard many nights and left things undone at home to get this Jeep ready for this event, I saw in this moment that this event was bigger than me or my Jeep. These veterans, men and women who were at the D-Day Memorial were there to remember all their fallen brethren. Their memories to day were as like yesterday for them. I wore my WWII uniform out of respect for these men and women. I and my fellow 101st Chapter member, Kevin Frank were stopped several times and thanked for saving them from desperate battles where less than one third of their unit survived. The 101st patch carries more meaning than I even could imagine. I spent so much time with these veterans and did not get to meet nearly as many as I wished. They were so humble but in all of us as we get older we just want to be remembered and know that we left an impact for something good and important here on earth. All branches of the service were there and all had a huge part. Few came home. I did not get to give rides to some vets as I had wished. The event was not set up that way. Instead I got to be a part of their lives for a brief moment. I am thankful for that. God bless these brave men and women. The Jeep had it moments in the spotlight. It was instrumental in helping to win the war. Many people took pics of it but I spent my time with the true vets who one the war. I will post some up tomorrow. But it is hard to take pictures with no one to take them for you. For the few I have I must thank Kevin Franks son.
What I started with on Thursday the 5th in the morning is what you see with the scabbard. No seats, no tank, no wiring, no headlights, no taillights. Still the 7.00 x 16 NDCCs on the back. I worked till 11pm and put 6 miles on it and had to get up a 6am and leave by 6:30 to get there. About 100 miles.
Done as best I could for the Memorial. Still so much more to add.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/IMG_0591_zpsf5733fcf.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/IMG_0590_zps385c4e80.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/IMG_0589_zps8b16ee2d.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/IMG_0587_zps3ecfa4fb.jpg)
-
Right as I pulled up into the Memorial the fuel pump broke. I called NAPA, Advanced Auto and no go. Two other jeeps were there. I asked the first one and he had none. He trailered. I asked the second after calling the parts store and he had a brand new one in an ammo box. Yes, God answered my prayers of getting me there and home. On the way home my generator went out with a bad bearing and brushes and an oil leak from using the old fuel pump gasket and I didn't have a new one. For a 200 mile round trip on and untested Jeep with a stock engine and transmission from the 40s not rebuilt, I say not bad. An experience I wouldn't trade for the world, But the reenactors with the two other jeeps there voiced my wife, Julie Kalamaja's, statement. You are not trailering It? NOPE!
The old Airtek pump and the new military replica one I got from Dave Ostrander, owner of the MB that was there.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140609_194406_zps06c22733.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140609_194433_zps18f6fd71.jpg)
Love the manual priming lever.
-
At the National D-Day Memorial with my friend Kevin Frank.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/IMG_0579_zps4ce36114.jpg)
-
Very Nice, thank you for sharing!
-
Adjusted the clutch to day as it was giving me some grief on the way home. Not the cable but a rod the PO had made. Locking nut came off and rod had shifted.
After that I installed some footman loops on the tool side of the early 46 2A tub as they are close to the square ones on the military jeeps.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140611_194513_zps8d78605d.jpg)
-
Got a few things in the mail from Debella and decided to put a few of them on. Got the full hardware for the top bows. The unmarked ones as they were the cheapest.
I made a template out of paper and set it on the GPW tub I have to get the holes for the bow hardware and the grab handles in the right spots. I ordered two new grab handles and am using two original GPW ones.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140614_155021_zps17123bf7.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140614_163925_zps5b23f9c1.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140614_171203_zps4e7c9438.jpg)
-
Put the other set of hardware on the other side and decided to set the top on. I picked this top up last year for $40 at a Jeep meet. It needs some repair but I think repaired it will add character to the Jeep.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140614_204338_zps60d9c12d.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140614_204355_zpsbcd8866a.jpg)
-
Field repaired the top. Standard sewing machine did pretty good. Fixed the rip on the rear corner and around the rear window. Also did a couple of patches on the top as well.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140616_212603_zps1fa164c5.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140616_212525_zps499bdd7a.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140616_213027_zps0ce241ab.jpg)
-
Got some time on my hands for a few days and this part of the Jeep required no hard manual labor. Can't afford the good stencils so put some together, traced them onto the hood and hand painted them. Still need to do the other side and make some invasion stars.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140620_152956_zps04f01d81.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140620_153047_zpsb5e77ad6.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140620_204406_zpsa76800ab.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140620_210259_zps2594397d.jpg)
-
Looked like your stencils did the job just as well as the high dollar kits.. Nice work!
-
Looked like your stencils did the job just as well as the high dollar kits.. Nice work!
Thanks! A long as you stay inside the lines. Glad I practiced with those crayons as a kid. ;) ;D
-
Very nicely done Zooke! Very nice. You have far more patience and painting skills than I do.
I'm left handed. When painting something like that, I have to start from the right and work left. Otherwise, I drag my hand through the fresh paint. :(
Tim
-
Got the stars painted on. Used masking stencils for spray paint on these...but brush painted them to match the hand painted numbers like would be done in the ETO.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/Mobile%20Uploads/20140625_180228_zps3024abda.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/Mobile%20Uploads/20140625_180239_zpsb3d9abee.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/Mobile%20Uploads/20140625_180646_zps263bfa7c.jpg)
-
Zooke nice work on the entire project...
Any significant's to the numbers or letters?
-
Zooke nice work on the entire project...
Any significant's to the numbers or letters?
Bumper numbers represent the history of the 321st Glider Artillery. I was stationed with the 101st Airborne and Bravo Battery 321st Field Artillery from 1976 to 1978. B-13 was my vehicle number.
-
So, I have a question.
On WWI US aircraft with a star in the roundel and WWII US military aircraft with stars and bars the stars on the wings are always oriented with one point of the star directly forward, in the direction of flight.
On jeeps it seems the stars are always oriented with one point headed directly aft....
Anyone know why?
-
Probably more for asymmetric reasons than anything else. It looks odd on plane facing aft.
-
Well, I think it looks odd on a jeep facing aft....but that is the way it is....
-
Originally the stars faced one way and then later on the Army changed the direction. I'd have to pull out the marking manuals to determine when the change took place.
So that doesn't answer the question why?????? ;D
-
Not only does the star point in the direction of flight, they point in the direction of the fight. I like to believe the change occurred to signify the direction forward. The direction into the fight.
This is my thought only. I have no idea why the change was made...
(http://i1195.photobucket.com/albums/aa397/athawk11/20120309001.jpg)
-
I like the "Direction of Fight" explanation....but in spite of that most are painted pointing aft...
Here is an explanation of markings, but I did not see the orientation mentioned...
http://www.stugiii.com/images/US_Vehicle_Markings.pdf
Maybe this needs it's own thread?
-
[media]https://www.youtube.com/watch?v=5fH_8qDEmzE[/media]
-
It's been a lot of fun watching your build. It's great to finally go for a ride in it.
One question though - Do you always make your wife ride in the back seat ? ;D
-
Nice job! I'd say that is a pretty darn good representation of a WWII jeep, only a few small details give it away as a civilian model but 99 percent of the people out there would never know. Great to go for a ride too. Thanks for posting.
Were you holding the shifter to keep it in gear or ??
-
Were you holding the shifter to keep it in gear or ??
No, just always keep my hand on the shifter for some reason. I even did when I drove the M151s in the army.
-
"Short Round"� doing what he was meant to do.� Represent!� With Norwood Thomas of the 101st Airborne. (D-day, Operation Market Garden, Battle of the Buldge, Bastogne") two young future generation and myself.� At the National D-Day Memorial in Bedford, VA.�
https://www.facebook.com/NationalDDAYMemorial
(http://i641.photobucket.com/albums/uu137/sundialmotosport/IMG_0722_zps960923f1.jpg)
-
A big thumbs up and a standing ovation are deserved...I miss the events with veterans I used to go to with my GPW..I always got more out of it than the vets, I think. The kids might contract Willys disease, I hope you had their parents sign a waiver.... :D :D
-
Well my transmission and transfer cases are leaking around all the gaskets I did not replace. Also it grinds a little in 3rd. Sometimes not but most times a little. It did more till I replaced the shift tower with tight forks.
So I took apart transmission #2 to make sure it was good for resealing and a lot of pitting in the needle bearing areas. All else looks in good shape.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/IMG_0806_zps219f51e7.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/IMG_0804_zps14733314.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/IMG_0803_zpsec43f286.jpg)
-
I took apart transmission #1 that was in the plow jeep as it worked great and I never had a problem with it.
Wrong. It was rebuilt at one time and I guess either being in a plow jeep killed it or it was rebuilt incorrectly.
broken teeth, burnt and blue gears, broken and bent slinger, missing needle bearings and retainers. What a mess. Worn needle bearing surfaces and galled bushing surfaces on the housing.
And the wrong gear lube as it ate away at the brass sync gears.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/IMG_0807_zps6d201936.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/IMG_0808_zps612d6eee.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/IMG_0809_zpsab9d3494.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/IMG_0811_zps526c617d.jpg)
-
Since they actually are jeep accessories if you have a Military Jeep.
Yard sale military haul today. Saw a yard sale and decided to a take looksee. Came away with a WWII winter coat, M1 Garand ammo belt, 2 WWII wool blankets. Korean War- 2 field pants. Vietnam War - 20rd M16 mag., helmet nap strap, fatigue belt, dust goggles and web belt. All this stuff fits. All for $30.
Since my type of jeep was the mainstay of jeeps during Korea, I can also do that era as well now.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/STUFFJEEP_zpsb5737e11.jpg)
-
Been working on the transmission and transfer case. Transmission is done. And now working on the transfer case. Boy are these things busy. I think it was leaking from every possible gasket and seal. I hope now it will not leak and of course stay cleaner. Maybe a couple of pics tomorrow.
-
Worked on the transfer case these last couple of days. There are just too many places it can leak from on these thing. Man they are busy with seals and gaskets.
The gears inside were in very good condition from my Transfer case #1 (first jeep, plow jeep). Bearings were good as well. So it was taken apart, surfaces were cleaned and new seals and gaskets were replaced.
All the debris, brass and metal the migrated over from the transmission was flushed out and Bearings were cleaned and lubed.
Transfer pan with metal and brass from the transmission.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140729_114231_zpsfe88a56f.jpg)
Gears looking good. Rear output and brake assembly installed and safety wired.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140729_114239_zpsa03a97af.jpg)
Four wheel drive housing cleaned and ready for install.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140729_172010_zps153a43c4.jpg)
Selector housing installed and safety wired.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140729_202800_zpsd5752e56.jpg)
-
When trying to mate the transmission to the transfer it kept binding the lower gear set and reverse idler gear.� Way too much drag and nearly impossible to turn.�
The transfer case was a 41xxx number.� I initially thought it was the length of the bolts.� Tried a shorter bolts.� Same thing, binding.� � Took a look at the transmission cases on both ones I took a part and looked a� both transfer cases.� The 41xxx transfer cut outs for the lower shaft rod and reverse idler rod are totally different.� The 41xxx has only a small cutout for the shim holding the shafts as the later 52xxx has a larger cutout that accepts the shims in the rebuild kits.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140729_172935_zps1b55e5cb.jpg)
Notice the small cutout for the shim.� Once I modified the shim and bolted things back together all worked fine and it shifted through all gears with no binding.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140729_114303_zps7bbdd2bf.jpg)
And on #59xxx you can see the larger cutout of a bigger shim and no chance of warping the cases when bolted together.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140730_094111_zps375a0d74.jpg)
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140730_094131_zps22279dd4.jpg)
This had me puzzled for a bit till I went back and forth and looked closely at both transfer cases.
-
Need to bolt the shift tower on, cotter pin the output gear and bolt down the back cover. Then ready for install.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/20140729_213843_zps0eacce79.jpg)
-
Looks like it's coming back together nicely. Great work.
Time permitting, I will hopefully tear into mine this weekend.
Again, nice job.
Tim
-
I wanted the rear axle on Short Round to look the part. Nothing is worse to me than a replica and the rear axle is a CJ. So I happened to be looking at other projects one day and lo and behold...none other than jpet had made exactly what I needed. Faux Floater ends for your CJ axle.
I had msgd him about what I needed and set about doing so. I traded a set of "F" marked GPW rear seat hooks for a set of repro ones and a set of bad front brake hubs with the brake part pressed off. I had these brake hubs sent to jpet of him work his magic on.
He turned down the brake backing plate as I didn't need it that thick and didn't want my wheels spaced out that far anyway. He then made a set of axle ends out of aluminum for me to bolt on.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/hubs1_zps0002db77.jpg)
-
Hubs and axle ends blasted, primed and ready for paint.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/hubs2_zpsc0d43959.jpg)
The rear axle and wheel as they looked before installing the Faux Floaters.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/hubs3_zps84639e8c.jpg)
The finished project. I opted to have the bolts used in aiding the removal of the rear floater axle added as I had seen this done on a couple of jeeps. I guess they kept them there so as not to loose them. People came up to me and told me a had a couple of bolt loose on my jeep. Had to explain. It was fun.
(http://i641.photobucket.com/albums/uu137/sundialmotosport/hubs4_zps23f6ac93.jpg)
-
Now that's a fine set of full floaters you have there...That is too cool!