The CJ3A Page CJ3B.info

Post reply

Warning: this topic has not been posted in for at least 120 days.
Unless you're sure you want to reply, please consider starting a new topic.

Note: this post will not display until it's been approved by a moderator.

Name:
Email:
Subject:
Message icon:

Verification:
Type the letters shown in the picture
Listen to the letters / Request another image

Type the letters shown in the picture:
Write the word between words Jeep from this JeepWILLYSJeep?:
How many slot has a GPW grill?  7 - 9 - 11:

shortcuts: hit alt+s to submit/post or alt+p to preview


Topic Summary

Posted by: corpsman
« on: April 10, 2015, 01:44:05 AM »

looks like you do good work.  it all looks great.
Posted by: BJ
« on: March 30, 2015, 05:47:16 AM »

I made a linkage adjustment to the starter and it worked fine all weekend. Every once and a while it would grind but it worked a lot better. I'll get it a new starter gear just to be on the safe side.

Test results from this weekend reveal that it's having trouble starting when cold. It would have fire and gas but not want to start up. Two mornings I had to give it a small sniff of carburetor cleaner to fire up. After that it would run fine all day. I'm thinking a new set of plugs should help out.

Also it was spilling oil out of the air breather after some of the rougher roads. Is this normal?

All in all everything went very well. It looks like I will be ready to start on some of the body work after a few changes.

Posted by: bretto
« on: March 27, 2015, 07:35:31 AM »

Those are great pics.
Those youngins better respect their elder. :)
Posted by: BJ
« on: March 27, 2015, 07:31:45 AM »

It almost looks out of place next to these off-road monsters.

[/URL

Posted by: BJ
« on: March 27, 2015, 07:30:53 AM »

Next I am going to start on some of the body work but for this weekend it's my transportation around the race track.









Posted by: BJ
« on: March 26, 2015, 08:10:08 PM »

I took it out to the race this weekend. (I help run an off-road racing series) so fare it is working better than it ever has.

This picture makes me reailize that the Willys Jeep is the original side by side.  ;D

Posted by: JeepFever
« on: March 24, 2015, 10:54:05 PM »

Quote
I am super happy with how it all turned out. It all works so very well. It drives and shifts like it never has before.

Nice work!  . . . it is so satisfying to make things better.
Posted by: Ryan_289
« on: March 24, 2015, 09:50:56 AM »

Quote
Next on the list if things to do is the starter. The starter is not wanting to engage properly all of the time. Sometimes you push the starter pedal and it just grinds. If you wiggle it around and push it you get a perfect start. I think the end of the starter is warn out.


You might just need a new bendix.  Not to hard to replace.
Posted by: Ryan_289
« on: March 24, 2015, 09:48:40 AM »

I made the mistake of cutting the rubber dowels for the rear main flush once.  I didnt wait around to see if they leaked, I just installed new ones. It still sucked to redo it again!
Posted by: BJ
« on: March 24, 2015, 05:10:56 AM »

Next on the list if things to do is the starter. The starter is not wanting to engage properly all of the time. Sometimes you push the starter pedal and it just grinds. If you wiggle it around and push it you get a perfect start. I think the end of the starter is warn out.
Posted by: BJ
« on: March 24, 2015, 05:05:48 AM »

Everything else looked good





So after cleaning everything up I started to put it back together.

The ring and pinion had been ridding a little low on the tooth but the gears where still in very good shape so I re used them. I did install all new bearings and gave it a proper gear set up. Then after tackling the outer bearings it was time to re install the axle.

I am super happy with how it all turned out. It all works so very well. It drives and shifts like it never has before.

Posted by: BJ
« on: March 24, 2015, 04:58:55 AM »

Ok. This passed weekend I completed the tranny install and started putting the drive line back together. I found the pinion loose on the rear axle so I yanked it iut and took it apart.




Everything was loose inside. It looked like the carrier bearings had spun a little as well.
Posted by: BJ
« on: March 03, 2015, 10:47:59 AM »

Yup.
Posted by: athawk11
« on: March 02, 2015, 04:31:20 PM »

BJ,
You will want to leave them long.  I believe you want approximately 1/4" sticking above the cap. They get seated and squished when the oil pan is re-installed. 

It looks like one of your crank to flywheel bolts was removed.  I know you probably already put it back in, but if not, there is no better time than now. ;)

Tim



Tim
Posted by: BJ
« on: March 02, 2015, 01:05:34 PM »

The tranny and transfer case are now complete. They are painted and put together ready to go back in. I took my time with it and I am sure that it's going to work like it should. I'll put up a picture of the assembly when I rember to take one.


I had a leak on the rear main seal of the motor so there is no better time than now to take care of that. I pulled the pan after ordering a new seal kit from Walcks. I was able to get the new seal in with no huge problems but now I am left with a question. There is two rubber pins that go in on eather side of the rear main cap. The new ones that where in the kit are to long. Do I cut them flush or mash them in with the oil pan. I measured the hole that they go in and it looks to be about 1/2" longer