The CJ3A Page CJ3B.info

Post reply

Warning: this topic has not been posted in for at least 120 days.
Unless you're sure you want to reply, please consider starting a new topic.

Note: this post will not display until it's been approved by a moderator.

Name:
Email:
Subject:
Message icon:
Verification:
Type the letters shown in the picture
Listen to the letters / Request another image

Type the letters shown in the picture:
Write the word between words Jeep from this JeepWILLYSJeep?:
How many slot has a GPW grill?  7 - 9 - 11:

shortcuts: hit alt+s to submit/post or alt+p to preview


Topic Summary

Posted by: athawk11
« on: June 06, 2022, 10:14:06 PM »

Just an FYI...

Brent Mullins Jeep Parts is a legitimate business.  Brent has been around for years.  He has a good reputation in the Willys universe.
Posted by: Rus Curtis
« on: June 06, 2022, 08:23:40 PM »

Got all my hand brake guts from Harry Sheets.

http://www.midwestwillys.com/

The replacement cable came from Walck's
Posted by: Marla.the.V35
« on: June 06, 2022, 06:54:28 PM »

FB marketplace or ebay and proceed with caution.  Try to find local so you can see it before buying. 
Posted by: Tchara
« on: June 06, 2022, 05:20:13 PM »

Hey Jon
Here's the info you wanted. Sorry it took so long. I plum forgot.
Brent Mullins 386-788-8838
BMJP (Brent Mullins Jeep Parts)

I've made a little progress. I have the new gas tank in it. A new Master cylinder, however failed to replace the dist. block and compression washer, so it's leaking. Have new hardware oirdered. Today I heard it run for the first time. (about 10 sec)
It sounded pretty good. I still am soaking the tranny, so the shifter cover is still off, and tranny fluid was spitting everywhere. And I think the fuel pump is bad. For the 10 seconds it ran, I wasn't getting any fuel to the carb feed line.
I have the new steering wheel and horn button. The old one was a booger to get off. I ended up using a cutting wheel and cutting the side to get it off. The splne and threads look to be in great shape.

I was underneath it today, and realized the entire emergency brake assembly is missing. The handle is on the dash, but the cable has been cut by the transmission. I'm going to have to try and find a used one if I can, because ordering the whole assembly from a online parts store is going to be prohibitory expensive. Any suggestions?
Posted by: Tchara
« on: June 04, 2022, 08:31:53 AM »

I have his business card, and I'll post the information next time I'm in the Garage.
Sorry it's taken awhile for me to reply.
Posted by: Marla.the.V35
« on: May 31, 2022, 01:53:39 PM »

What's this person called on FB Marketplace? Got any rear seats? :D
Posted by: Tchara
« on: May 28, 2022, 07:52:35 PM »

Yes...I realized that when I got home and started looking at it. Next week I'll go back to college station, and exchange it for the right one.
Posted by: athawk11
« on: May 26, 2022, 11:51:52 PM »

The driver side seat frame appears to be from an M38.
Posted by: Tchara
« on: May 26, 2022, 09:01:53 PM »

Went to College Station today to check out some jeep parts. It's about 100 miles from the house. The guy has a huge warehouse, where he collects everything military, including tanks and vehicles. I found him on FB Market. I'm not on FB, but a friend lets me use her account to get on the market place. 

So....I found a good windshield frame, with a cracked windshield to boot, for 250.00. I also picked up the original seat frames. Some one fabricated some frames that were kind of hay wired together. I gave 100.00 for the drivers side, and 150.00 for the passenger. The driver side isn't quite right. The front right leg is a little different, but the other 2 holes are fine. There NOS. May do a little fabrication of my own.

I think for 500.00, I did pretty good.
Posted by: Tchara
« on: May 26, 2022, 07:45:43 AM »

Never thought about that. I guess with the seats so far up, your feet couldn't reach the floor. Thanks for the insight. I guess I was just to excited to figure it out....LOL. Any hoo....it's coming off too.
Posted by: Rus Curtis
« on: May 25, 2022, 11:08:12 PM »

It appears to have been added as a footrest for the back seat occupants.
Posted by: Tchara
« on: May 25, 2022, 09:42:27 PM »

Well, I got it in the garage today. Had to pull the AMC Pacer out and put on the back burner. My plan is to get the jeep road worthy, so I can drive it while I'm working on the pacer.
As you can see, the back seat frame is off. I used my shop crane to lift it off.
There is a cross member (2nd photo) that I'm wondering if it's original, or some one added it with the seat frame.
Looks to me it is an add on, because the pipe looks like the same material used for the roll bar.
Posted by: SteveKfl
« on: May 25, 2022, 06:13:59 AM »

And the adventure has begun.  Enjoy!
Posted by: Marla.the.V35
« on: May 25, 2022, 12:13:19 AM »

Looking forward to this rescue!
Posted by: Tchara
« on: May 24, 2022, 10:33:57 PM »

Well....Got the new baby (cj3a) home this morning. If you haven't read my intro post, I bought a 1952 Cj3a about a week ago. My buddy has a car trailer, so had to wait until he had the time to pick it up.
As you can see in the pic, someone had turned it into a hunting vehicle, probably for a deer lease. I started removing the whole rear frame where the seats are. But spent most of the day working on the old auto lite starter. I finally figured out the push switch was so dirty and corroded, it wasn't making contact. So cleaned it all up the best I could and got the motor to turn over. I sprayed PD Blaster in all the cylinders for good measure and will wair until I get the new tune up parts, before I try and start it.

I'll add to this post as I progress on this sweet ride. Looking forward to jumping the mud puddles. Gonna name her the Puddle Jumper!