The CJ3A Page CJ3B.info

Post reply

Warning: this topic has not been posted in for at least 120 days.
Unless you're sure you want to reply, please consider starting a new topic.

Note: this post will not display until it's been approved by a moderator.

Name:
Email:
Subject:
Message icon:

Verification:
Type the letters shown in the picture
Listen to the letters / Request another image

Type the letters shown in the picture:
Write the word between words Jeep from this JeepWILLYSJeep?:
How many slot has a GPW grill?  7 - 9 - 11:

shortcuts: hit alt+s to submit/post or alt+p to preview


Topic Summary

Posted by: Mytwojeeps2020
« on: April 26, 2022, 06:56:13 AM »

Thanks, Jon. I’ve never had anything but non-greasable shackles here in Central Florida. I never knew greasable existed until I saw them advertised by KW. That’s why I asked. I guess the greasable ones are for the older machines. My CJ5’s PO came from a heavily salted road area up north. The shackles are looking pretty bad, so I’m going to change them out. I just didn’t know which ones to use.
Posted by: Marla.the.V35
« on: April 25, 2022, 02:28:50 PM »

tbh, if this jeep wasn't so rare, I'd strongly consider moving to a non-greasable. As it is, I'm trying to keep it as close to current, or revert back to stock but with safety prevailing in the end.

Only considerations I can see for poly bushings is for climates in which they don't do well (Florida or anywhere with salty roads in the winter).

There's a gentleman named Sal Walter (not sure if he's here, but he's in the same Facebook groups I am) making parts using oilite. He's considered making spring bushings and packaging them with Grade 8 bolts for this. Might be worth seeking him out if you're planning to change.

hth
Posted by: Mytwojeeps2020
« on: April 25, 2022, 08:53:56 AM »

I’d like to bring up Jon’s topic to address something related to his project.

Does anyone have an opinion on whether to use greasable or non greasable shackles?
Posted by: Rus Curtis
« on: February 26, 2022, 05:07:08 PM »

The Service Manual doesn't show a washer.  There may be another reason that washer was added.
Posted by: Marla.the.V35
« on: February 26, 2022, 04:47:30 PM »

Does the spring eye bolt need a washer on the outside? That's a splined bolt that you press in, so I assumed no. Am I incorrect? (pic from the interwebz)
Posted by: Marla.the.V35
« on: January 23, 2022, 11:48:58 PM »

Thanks, oldtime!
Posted by: oldtime
« on: January 23, 2022, 07:42:16 PM »

Manual states 25 to 30 pounds feet.
Posted by: Marla.the.V35
« on: January 23, 2022, 04:18:27 PM »

Having trouble tracking down torque specs for the shackles. Some say 25-40ftlbs, some say around 75. Unfortunately don't have my manual with me today.  Anyone know or can check theirs and help me out? Thanks!
Posted by: Marla.the.V35
« on: January 09, 2022, 09:06:41 PM »

First one is on! Thanks, everyone!
Posted by: Rus Curtis
« on: January 03, 2022, 10:38:09 PM »

My mistake. For some reason, I thought everything was bolted up except this.  Since its all loose and the C shackle isn't attached, maybe get a garage helper to wiggle the spring (shackle end) while you wiggle the bolt into its mount.  It might be easier to get the springs mounted (since there's a chance of tolerances being off a bit), then attach the axle.

I'm guessing once it's all together and greased, it should work okay.

For peace of mind, with the axle out of the way, it will be easier to measure the criss cross distances in Section, R, FRAME.  The back measurements are C-D (the spring mounts):  48.48"
Posted by: Marla.the.V35
« on: January 03, 2022, 08:19:19 PM »

I'll give this a shot (bottle jack under spring plate same thing?) 

It's up on jackstands currently and the rear axle has the u-bolts on finger tight (threaded so the bottom of the nut is flush with the bolt), The spring pin is centered in the axle's spring bracket. Should I detach the rear axle first?

Also,  the rear shackle is currently removed. I assume if compressing the spring,  that'll need to be reattached?

Almost forgot..i just attached the spring to frame brackets yesterday.  Is it possible this will be a problem even if that bolt goes through?

I appreciate the advice, I'm feeling a little dejected by this. I hope I'm just jumping to the worst case scenario, (installed bracket crooked, frame bent,  worried about binding) but maybe it's nothing...
Posted by: Rus Curtis
« on: January 03, 2022, 08:06:51 PM »

Try lowering it and as the spring begins to compress (flatten) it may push that bolt back just enough to get it to feed through the hole.

With all the connecting parts, there may be an advantage to leave everything a bit loose until all the threads are in and then you can check alignment of the axle (shouldn't be much) before tightening everything down.
Posted by: Marla.the.V35
« on: January 03, 2022, 06:44:17 PM »

Well....crud...

Looks like there's a slight twist somewhere and I can't get the spring eye bolt all the way through :(
Posted by: Marla.the.V35
« on: January 01, 2022, 01:23:55 PM »

So,  turns out the Walcks4wd stuff is totally correct.  I ordered lower shock plates from KW and one of them is incorrect/has too narrow holes/is possibly for a different vehicle with a smaller diameter axle. Anyways,  the other shock plates are correct and were within tolerance.  Thank you everyone for your suggestions!
Posted by: Bruce_W
« on: January 01, 2022, 11:05:42 AM »

If they are too small for the axle housing and “flare out” when you push them over the housing, they are wrong. Don’t tell me, let me guess - Omix-ADA? Kaiser-Willys? Send them back.
Normal adjustment usually involves a bit of squeeze in a vice if too wide or clamping one end in a vice and pulling on the other with a piece of pipe if too narrow. This should only amount to less than half a bolt diameter of mis-match.
BW