The CJ3A Page CJ3B.info

Post reply

Warning: this topic has not been posted in for at least 120 days.
Unless you're sure you want to reply, please consider starting a new topic.

Note: this post will not display until it's been approved by a moderator.

Name:
Email:
Subject:
Message icon:

Verification:
Type the letters shown in the picture
Listen to the letters / Request another image

Type the letters shown in the picture:
Write the word between words Jeep from this JeepWILLYSJeep?:
How many slot has a GPW grill?  7 - 9 - 11:

shortcuts: hit alt+s to submit/post or alt+p to preview


Topic Summary

Posted by: LKap
« on: April 27, 2018, 04:14:07 PM »

Update - I tried the MAPP and it wasn�t hot enough so I went to the local big box store and got a Bernzomatic MAPP-Oxy kit for $60 bucks. Worked great. I was able to heat the brake arm cherry red and bent it easily. Got lucky on the first try and it fit perfectly.  The kit was a little pricey but now I have it for when I need to get rusty bolts out. Thanks for all the help guys. On to the next project!
Posted by: Tumbleweed
« on: April 25, 2018, 07:48:21 AM »

Quote
Tumbleweed,

What did you use to bend the brake arm?� I don�t have an oxy-acetylene torch. Best I can do is MAPP.� Will that be hot enough?

LKap

I heated with oxy-acetylene. I suppose you could do MAPP but you need to get it red hot. Took me a couple of trys to get the correct bend I needed to clear the hole without rubbing. I would try the MAPP and see if it works.
Posted by: Tumbleweed
« on: April 25, 2018, 07:44:33 AM »

Quote
Quote
Hi Tumbleweed!

I got the 5/16"-24 Clevis on eBay.� Can't remember the seller, but they were around $4.00 each.� I picked up some 5/16" steel rod at the hardware store and threaded them.� �I made the pins by cutting off a 5/16" bolt and drilling a hole for the cotter pin.� Although, you can get the pins at any Ace Hardware.� It's a fun project and makes that 'link' nearly indestructible.�



George, I did the same thing as Hawk and could find everything I needed at Ace.� I'll add that you will not be able to find clevis' and all-thread that match threads.� I looked everywhere and the only option is to make your own.� For the clevis pin, I just took one of the ones that comes with a bunch of holes already drilled and then just cut it down to the length that would fit in the opening.

Thanks guys I knew I could count on you. I have been wanting to do this for a while. See you boys soon!
Posted by: LKap
« on: April 24, 2018, 06:57:22 PM »

Tumbleweed,

What did you use to bend the brake arm?  I don�t have an oxy-acetylene torch. Best I can do is MAPP.  Will that be hot enough?

LKap
Posted by: aboyandhisdog
« on: April 23, 2018, 11:56:39 AM »

Quote
Hi Tumbleweed!

I got the 5/16"-24 Clevis on eBay.� Can't remember the seller, but they were around $4.00 each.� I picked up some 5/16" steel rod at the hardware store and threaded them.� �I made the pins by cutting off a 5/16" bolt and drilling a hole for the cotter pin.� Although, you can get the pins at any Ace Hardware.� It's a fun project and makes that 'link' nearly indestructible.�



George, I did the same thing as Hawk and could find everything I needed at Ace.  I'll add that you will not be able to find clevis' and all-thread that match threads.  I looked everywhere and the only option is to make your own.  For the clevis pin, I just took one of the ones that comes with a bunch of holes already drilled and then just cut it down to the length that would fit in the opening.
Posted by: athawk11
« on: April 23, 2018, 10:56:29 AM »

Hi Tumbleweed!

I got the 5/16"-24 Clevis on eBay.  Can't remember the seller, but they were around $4.00 each.  I picked up some 5/16" steel rod at the hardware store and threaded them.   I made the pins by cutting off a 5/16" bolt and drilling a hole for the cotter pin.  Although, you can get the pins at any Ace Hardware.  It's a fun project and makes that 'link' nearly indestructible. 

Posted by: Tumbleweed
« on: April 23, 2018, 08:47:37 AM »

Quote
Very interesting - I don't think my brake arm has that bend in it. I'm gonna try to take it all apart later and get a better pic. Maybe it's from a later model?
Yes interesting but if I look at mine they have some strange bends as well. I also made a slight bend in my brake arm as it would rub on the tub. I put a little heat to it and bent it a little to clear the opening in the tub floor.
Posted by: Tumbleweed
« on: April 23, 2018, 08:44:36 AM »

Tim,

Do you have deatils on the clevis pins? Also did you thread the rods yourself? I was looking at making the same mods to both my jeeps.

Thanks,

Tumbleweed
Posted by: athawk11
« on: April 22, 2018, 07:17:12 PM »

The arms are pretty tough.  Heating and bending won't cause any problems.
Posted by: athawk11
« on: April 22, 2018, 07:14:41 PM »



Posted by: 1955CJ-5
« on: April 22, 2018, 12:42:45 PM »

Your cross shaft looks worn alright.....check the tube that's welded to the frame also....

And while your at it, consider replacing that bent steel clutch actuating rod with a heavier steel rod threaded for clevis ends...can't find a picture right now but there have been threads in the past.....maybe Tim has a pic..?

The bent steel rods seem to break pretty regularly....
Posted by: LKap
« on: April 22, 2018, 11:30:31 AM »

New development!  I thin the problem is the cross tube.  It looks like bubba has been here.  It has been sleeved on the brake side for sure.  I wonder if it's even the right length.  Anyone have measurements? 

Oh and why do my pictures look so jacked up? Taken with iPhone/iPad and uploaded directly
Posted by: LKap
« on: April 22, 2018, 11:08:15 AM »

Thanks for all the info guys. I took it apart this am and here's what they look like. I'm pretty sure both pedal shafts are bent. Will it weaken them catastrophically if I heat and bend them?  I also noted that the cross tube is pretty worn. I'm thinking the best plan might be to buy a whole new setup and compare old and new when it arrives. Keep what I need and send back the rest
Posted by: 1955CJ-5
« on: April 21, 2018, 10:06:23 PM »

I found the receipt for mine..got it through ebay..still coated in cosmoline..

Brent Mullins Jeep Parts in College Station TX.

https://www.ebay.com/itm/Jeep-M38-M38A1-NOS-Brake-Pedal-Arm-/170998093718



Posted by: athawk11
« on: April 21, 2018, 05:12:52 PM »

I had to replace my worn out brake pedal arm.  The reproduction was almost straight. When compared to the original, it wasn't even close to having the correct bends to get it to line up with the hole.  I had to heat and bend it to get it to work.