The CJ3A Page CJ3B.info

Post reply

Warning: this topic has not been posted in for at least 120 days.
Unless you're sure you want to reply, please consider starting a new topic.

Note: this post will not display until it's been approved by a moderator.

Name:
Email:
Subject:
Message icon:
Verification:
Type the letters shown in the picture
Listen to the letters / Request another image

Type the letters shown in the picture:
Write the word between words Jeep from this JeepWILLYSJeep?:
How many slot has a GPW grill?  7 - 9 - 11:

shortcuts: hit alt+s to submit/post or alt+p to preview


Topic Summary

Posted by: Kikilee
« on: August 29, 2014, 06:42:41 PM »

Here are some more pics of the grill. I've got it ready for color after a little bondo, sanding, epoxy primer, sanding, hi-build primer and more sanding............... All in all I think it turned out nice.

 

 

 

 

Posted by: Kikilee
« on: August 29, 2014, 06:22:10 PM »

[size=8]Jesse, nothing on the inside, it's smooth. I'll try to get a pic up in a bit. Gunslinger, it could be a 2A grill I just don't know all the differences. [/size]
Posted by: Jesse
« on: August 29, 2014, 03:10:16 PM »

My 2a grill has little shelves for the parking lights that mount inside. Any evidence of something like that being removed?


-Jesse
Posted by: Gunslinger
« on: August 29, 2014, 01:30:22 PM »

CJ 2A?
Posted by: Bob W
« on: August 27, 2014, 04:45:23 PM »

DJ-3A?
Posted by: Kikilee
« on: August 27, 2014, 04:22:37 PM »

Stole this off EBAY:


Has the same bottom shroud and parking lights haven't been cut.
Posted by: PeterL
« on: August 25, 2014, 06:56:41 PM »

I use a Greenlee punch everyday.  Yes, I agree that it could do it but, when you look very closely the holes look identically offset.  It is highly improbable that those are aftermarket punches.  Could it be an aftermarket grill?? Made in the 60's?
Posted by: SteveW
« on: August 25, 2014, 04:02:04 PM »

A Greenlee punch that I use as an electrical contractor could make a nice hole like that and a hole saw could also but you would have to have a backer block to get the pilot hole going right. Not done freehand for sure.
Posted by: athawk11
« on: August 25, 2014, 10:52:18 AM »

The cut outs do look clean.� The give away is they are offset from the original bezel mounting holes.�

I'm fairly confident those large holes were not factory, but�I could be wrong.� I hadn't seen the bottom shroud design, until yours, either.

Only a guess, but perhaps a PO had access to a hydraulic punch ??

Tim� �
Posted by: Kikilee
« on: August 24, 2014, 11:03:54 PM »

Thank you gentlemen. My Jeep is a 1950 model. The second grill pictured is in much better shape than the other.

Tim if someone cut the parking lights out of this grill they did the best job I have seen. I swear it looks like that's the way it was made. Professional to the point that I can't tell.

I'm going to try and use the second grill pictured.

I am finding that I am accumulating enough parts that when I finish this one I'll probably have everything I need to do another. ::)
Posted by: Bob W
« on: August 24, 2014, 09:34:29 PM »

The center bolt remains.
Posted by: athawk11
« on: August 24, 2014, 09:32:46 PM »

I knew Bob would know.� Curious...Did they eliminate the center mounting bolt?� Or is there a hole in the shroud for access?

Tim
Posted by: Bob W
« on: August 24, 2014, 09:24:22 PM »

There were 3 different CJ-3A grills. The first was for the bottom mount radiator. The second was for the side mount radiator. The third was also for the side mount radiator but had the bottom portion of the "shroud" included.
Posted by: athawk11
« on: August 24, 2014, 09:09:43 PM »

The first grill looks like a typical late 3A grill.� It is the later design that accepts the side mount radiator.� The early 3A grill does not have the mounting holes on the inner flanges.

It actually looks to be in decent condition.� Maybe I'm not seeing the damage.�

The second grill is interesting.� The park lights have been cut out.� Probably to accommodate an after market set of turn signals.� That is somewhat typical.�

What is interesting is the lower inner flange.� I haven't seen that before.� It looks factory, so I may have to re-assess what I thought I knew about grills.

Even though the park lights have been cut out, it may still work with the original style park bezels and lenses.

Tim

Posted by: 1955CJ-5
« on: August 24, 2014, 08:46:06 PM »

Remind us...what year is your jeep?

Early 3a's had bottom mount radiators, and later they went to the front mount, but I don't have specific vin's for the change...

Edit: I looked in Bob's book and the change occurred for the 1950 model year, production started in November of 1949..


Mine is a 51 with a front mount, here is the grill: