The CJ3A Page CJ3B.info

Post reply

Warning: this topic has not been posted in for at least 120 days.
Unless you're sure you want to reply, please consider starting a new topic.

Note: this post will not display until it's been approved by a moderator.

Name:
Email:
Subject:
Message icon:

Verification:
Type the letters shown in the picture
Listen to the letters / Request another image

Type the letters shown in the picture:
Write the word between words Jeep from this JeepWILLYSJeep?:
How many slot has a GPW grill?  7 - 9 - 11:

shortcuts: hit alt+s to submit/post or alt+p to preview


Topic Summary

Posted by: scoutpilot
« on: August 01, 2013, 05:59:56 AM »

I was under the the impression that these were filled with alcohol. At least that's what I put in one years ago and it still works today. I will never do that again.
Posted by: stony
« on: July 31, 2013, 02:30:09 PM »

I bought the ether on e-bay.� Problem is that the smallest amount I could get was 500 ml, and that was $35, and $15 for shipping.� So payed a lot for the 15 ml or so that was actually used, but it was the challenge ;).� Anyway, looked at automotive starting fluid MSDS's (material safety data sheet) to see % diethyl ether and it was about 30% in the ones that I looked at, which was not enough (IMHO).� �Have since found this: http://www.greenpartstore.com/John-Deere-80-percent-Premium-Ether-Starting-Fluid-RE556468.html MSDS says 80% diethyl ether, 10-20% lpg.� That I believe would do it.� I believe that as long as there is liquid ether in the bulb the gauge should be reasonably accurate.� The lpg/ether mix may have some impact on the boiling point but it is probably not be enough to cause problems.� For $4 a can what the heck.

So this is what I wound up needing:

Various tools to clean out the rust.
Vice (or pliers) to uncrimp the flair.
Dremel tool to cut back the wire.
5/64 and 3/32 drills to drill for the tube. ($6)�
Soldering iron and solder to reattach the tube and remove solder from end of reservoir.
Couple of drills and taps, started with 6/32 wound up with 8/32
Blunt tip 3ml syringes from e-bay. ($7)
Teflon tape ($2) and valve packing ($3) (used 3/32 but would have used 1/16 if I could get it)
JB Weld ($5)
8/32 screw
Ether ($50) but the JD 80% is $4

So there it is, should be able to do it for about $15.� I don't see any reason why this should not keep on working for a long time.� Just need to clean up and paint the bezel.


Posted by: 1955CJ-5
« on: July 31, 2013, 12:50:55 PM »

Very nice! 

Where did you buy the ether?
Posted by: BMIC
« on: July 31, 2013, 12:45:48 PM »

Great work and a very interesting read... Thanks Terry
Posted by: stony
« on: July 31, 2013, 10:12:46 AM »

Think I got it :D!!
Posted by: stony
« on: July 30, 2013, 05:49:18 PM »

If only I knew then what I know now, LOL.� OK so have been thinking about how to do this thing.� Went and got some heavy duty soldering stuff, and was trying to figure out how to keep things cold and hot at the same time.� Then said wait a minute, this should be something that anybody can do and do it cheaply, so scrapped the whole solder idea and did some research.� Changed tack to see how to seal the capsule without solder.� Figured that my bottle of ether came in a aluminum can with a plastic top, and a plastic seal, I needed to just make a gasket out of somwthing to seal with a screw.� Drilled and tapped the end of the brass reservoir for a 8-32 machine screw, smoothed and polished the area around the screw as best as I could.� Found out that Teflon is insoluble in ether.� Cool, got my roll of Teflon tape and took a look.� Didn't think it would seal on the threads, but might make a gasket with several layers.� Was looking for something a little thicker, then BINGO!� Teflon valve packing rope.� Perfect!!� Thought I would make a practice run, wrapped a piece tightly around a screw that I had cut down to about 1/4 inch long, and screwed it into the reservoir tight enough to deform the Teflon.� Cut off the tag ends with a razor blade and took a look.� It looked like a perfect gasket.� Why screw around, lets go for it!� Tossed the can of ether and the gauge in the freezer to cool down.� Pulled it out, filled my (just arrived from e-bay) blunt neeedle syringe with ether and filled the reservoir.� Screwed it down tight as I dared.� Let it sit for a minute or so and gave it the sniff test, could not smell any ether escaping.� Mixed up a batch of JB Weld for a final seal.� Will test it out tomorrow.� I am dying to see what will happen.� Photos are the screw and gasket, installed screw, and epoxied reservoir and blunt syringe I used to fill.� Anyway so far so good ;)

Update:� Came back after an hour and there was a tiny bubble in the JB, did not even break the surface.� Scraped the JB off and gave it another 1/8 turn, reapplied JB.� The gauge reads a little over 100 now, where before it was bottomed out.� This is going to work!

Update 2:� Another tiny bubble, cranked it down another tiny bit, another 1/2 hour looks good!� Let er set up.

Update 3:  Dang!  Another tiny leak.  Think I know what went wrong.  Should not have preformed gasket.  Started over.  Looks good, so far.
Posted by: Jesse
« on: July 27, 2013, 03:50:52 PM »

Putting a small copper tube on there is actually a pretty good idea, it would have a smaller area to heat when you need to solder it up. Now that bulb probably draws a lot of your heat away when you are trying to seal it with a standard iron.

-Jesse
Posted by: 1955CJ-5
« on: July 27, 2013, 10:41:19 AM »

Stony,

When the gauges were new, would the entire capillary tube, Bourdon tube and bulb be filled with liquid ether?

Or would the bulb only be filled with liquid ether and the remainder ether vapor?

I suppose there needs to be room for vapor as that provides the pressure to expand the Bourdon tube...� I found a write-up on Bourdon tubes..interesting...
Posted by: stony
« on: July 26, 2013, 08:32:41 PM »

Matt:  That is a good idea, however CA glues are soluble in acetone, so I am pretty sure that they will not stand up to ether, which is an even better solvent.   Right now I am leaning toward soldering on a brass 6-32 nut and using a machine screw and an "O" ring for a physical seal then overcoating with epoxy.  I WILL make this thing work somehow! ;)
Posted by: Matto
« on: July 26, 2013, 07:38:19 PM »

If you need to fasten a plug in a hurry, there is a product called 2P10 which is basically Crazy glue on steroids. Apply adhesive to the base and spray a shot of accelerator to the plug. When the two parts meet, you will have a high strength bond in about 3 seconds. Good luck, interesting thread.
Matt
Posted by: 1955CJ-5
« on: July 26, 2013, 11:27:48 AM »

My gauge was stuck right where the picture shows, so I figured that I might as well take it apart. I bent the Bourdon tube, and to my surprise it worked.....calibrated it with a candy thermometer and a coffee cup..

For that Bourdon tube to get bent/straightened to the point where the needle was pegged, the engine must have gotten pretty hot....

That old 55 CJ has been in the family since I was 8......
Posted by: stony
« on: July 26, 2013, 10:17:28 AM »

CJ, yeah I have taken them apart before, did not want to except as a last resort.  I have some syringes coming so in theory I could fill it from the gauge end but would take forever.  Beginning to think it was originally filled and sealed cold and the solder was added to strengthen the seal.  Right now I am looking at two options: soldering in a small copper tube and crimping to seal or a small machine screw with a O ring to seal.  Will reenforce with epoxy rather than solder.  Anyway will figure something out ;).  BTW my first jeep was a 56 CJ5 :)
Posted by: 1955CJ-5
« on: July 26, 2013, 09:32:48 AM »

The gauges can be dis-assembled. The bezel ring is very soft steel. If I had thought to round the sharp edges on the screwdriver it would have been a smoother operation..as it is I marked the case a little, but not bad...

Posted by: stony
« on: July 25, 2013, 11:42:28 PM »

Thanks, yeah I have thought about that, problem is you would need a VERY hot iron to seal it, I have already thought about using epoxy, but it would never cure at low temp.   I am leaning toward soldering in a copper capillary tube and filling through that and crimping it shut, then soldering or epoxying. 
Posted by: Jesse
« on: July 25, 2013, 11:11:06 PM »

Just thinking out loud here, but could you drill a hole through a piece of dry ice and put the bulb through? That would leave the end open to solder but would keep the bulb and ether very cold. Still probably isn't going to work without a high temp iron though.

-Jesse


Don't mind the grade school illustration, you are getting what you pay for with this advice anyhow.