The CJ3A Page CJ3B.info

Post reply

Warning: this topic has not been posted in for at least 120 days.
Unless you're sure you want to reply, please consider starting a new topic.

Note: this post will not display until it's been approved by a moderator.

Name:
Email:
Subject:
Message icon:
Verification:
Type the letters shown in the picture
Listen to the letters / Request another image

Type the letters shown in the picture:
Write the word between words Jeep from this JeepWILLYSJeep?:
How many slot has a GPW grill?  7 - 9 - 11:

shortcuts: hit alt+s to submit/post or alt+p to preview


Topic Summary

Posted by: ranchhopper
« on: July 04, 2013, 05:41:54 PM »

SUCCESS moved the oil pump drive gear over two teeth now it runs like it was supposed to timing adjustment is in the center of the adjustment slots finally were ready to roll in the parade.
Posted by: ranchhopper
« on: July 04, 2013, 07:19:05 AM »

Solved the stumbling problem with the jeep yesterday I bought a new distributor the engine runs good now through acceleration but the timing issue still remains. I have no timing marks anywhere on the engine so I brought #1 cylinder to TDC and scribed some on the timing gear cover and pully. When useing a timing light there is a one inch gap between the marks timing is retarded and no adjustment left with the distributor. Today I am going to remove the oil pump and move the drive gear a tooth th get more timing adjustment. The old distributors advance weights werent working as they should and this distributor has the electronic ignition already built in its a pretty nice unit $125 shipped to my door.
Posted by: ranchhopper
« on: June 13, 2013, 06:32:07 PM »

Im still at an impass with my distributor mine is the later version pictured the springs on the advance weights seem pretty stiff. I wonder if they use the same spring maybe that is the problem if you gun it the engine takes right off but if you gradually accelerate it stumbles and wont accelerate past a certain point.
Posted by: 1955CJ-5
« on: June 12, 2013, 07:28:43 PM »

Finally got a couple of pictures...

sure looks a lot like yours...



Posted by: 1955CJ-5
« on: June 11, 2013, 09:17:55 AM »

It sure is similar to your's...I'll have to go look and get a picture...
Posted by: athawk11
« on: June 10, 2013, 03:39:33 PM »

I'm not familiar with the Disty on a CJ5.�
This was the best photo I could find of my current distributor. ( For some reason, I neglected to take close up photos of this side of my engine. )

What do you think?� CJ5 Distributor?

Tim



Posted by: 1955CJ-5
« on: June 10, 2013, 01:42:22 PM »

Thanks Tim,

Very helpful link.moving the plug wires is definitely thinking "outside of the box"...

You guys must have something similar to the distributor on the CJ-5, with the adjusting collar fixed to the distributor and a slot for adjusting...
Posted by: athawk11
« on: June 10, 2013, 11:05:14 AM »

Randy,
You are correct. You have the original distributor set up.� RH and I do not.� Ours are likely replacement distributors for later Willys.� The mounting hole in your mounting bracket is a mounting and adjusting slot for me.
 
Here is a post at the 2A page while I was fighting this battle.� It may be helpful to you and Ranchhopper.� Pay particular attention to the responses from Sean.� He is the guru on L-134 engine timing.

http://www.thecj2apage.com/forums/per-faq-l134-ignition-timing-by-sean_topic26318_page1.html?KW=timing

Tim

Posted by: 1955CJ-5
« on: June 09, 2013, 10:45:52 PM »

This discussion got me thinking as my engine will go together soon...so looking in the service manual reprint that I have paragraph D-85 explains the install of the oil pump and the orientation of the distributor drive.

But my distributor does not have the adjustment limiting slot, just a pinch bolt, so theoretically I could rotate it 360 degrees...or so it seems...

Do I have the right adjuster? The Distributor is an IAD 4008.



Posted by: athawk11
« on: June 09, 2013, 10:35:06 PM »

I was turned all the way to the right also.

It's been a while, but if memory serves, I turned it counter clock wise...peering down the distributor hole

or

Clock wise if you are looking up through the oil pump hole.

This is a helical gear on the oil pump.  The trick is to move it one tooth, (which I think represents about a 30 degree change) but the helical style gear will move when you re-insert it and it make contact with the gear on the camshaft.
Same thing when you pull it out.

I had a tendency to think I moved it one tooth, but it kept on ending up in the same place.  !%@$ helical gears!!!

Tim
Posted by: ranchhopper
« on: June 09, 2013, 09:16:27 AM »

Thanks Tim which way did you turn it I dont want to have to disassemble it again if I turn it the wrong way my distributor is turned all the way to the right the jam bolt is at the top of the adjustment slot on the back of the distributor.
Posted by: athawk11
« on: June 09, 2013, 08:57:55 AM »

RH,
� You are describing the exact same issue I was having.
� You have to pull the oil pump and move its gear a tooth.
 
 Which I must add, is a real pain in the rump on a fully assembled Willys.� I ended up pulling the exhaust pipe off the manifold.� This gave me a little more room, but it was still tight.�

I will add that once I was able to time the engine correctly, it ran like a fresh rebuild.

Tim
Posted by: ranchhopper
« on: June 09, 2013, 07:32:00 AM »

I have gone over the whole thing on the jeep now what I have noticed is the distributor has been turned all the way to the end of its adjustment. I have a friend who thinks it is one tooth off a vacuum gauge tells me its timing is running retarded but there is no more adjustment to advance it. How does one go about setting the distributor one more tooth forward since there is no drive gear on the distributor shaft?
Posted by: scoutpilot
« on: May 28, 2013, 05:56:22 AM »

If it is idling well, then you have no vacuum leak. I'm in the camp with the distributor problem. Gummed-up flyweights or worn posts they turn on, or springs that have lost their tension.
Posted by: ranchhopper
« on: May 27, 2013, 03:42:46 PM »

No I was going to check the timing too I looked for a vacuum leak but found nothing out of the ordinary.