The CJ3A Page CJ3B.info

Post reply

Warning: this topic has not been posted in for at least 120 days.
Unless you're sure you want to reply, please consider starting a new topic.

Note: this post will not display until it's been approved by a moderator.

Name:
Email:
Subject:
Message icon:

Verification:
Type the letters shown in the picture
Listen to the letters / Request another image

Type the letters shown in the picture:
Write the word between words Jeep from this JeepWILLYSJeep?:
How many slot has a GPW grill?  7 - 9 - 11:

shortcuts: hit alt+s to submit/post or alt+p to preview


Topic Summary

Posted by: ZekeD
« on: March 18, 2013, 05:53:13 PM »

Oh you mean DIFF lockers........    I was wondering why anyone would want GYM lockers.....

My bad.

Thanks
Zeke
Posted by: garage gnome
« on: March 17, 2013, 09:52:07 PM »

You may want to rethink a front locker... ESPECIALLY with manual ross box steering... Can you say dead arms? �;D I know with my trail rig which I welded the rear, it will go anywhere. Personally, I don't think the problem is open differentials. It is about how much the suspension flexes. Once you get a wheel in the air, you're junk. That is why I built a custom frame and coil spring suspension for it and kept the stock axles. I haven't gotten it stuck because of lack of traction, only because of stupidity of operator...  ::)
Posted by: Kenny_Kustom
« on: March 17, 2013, 09:50:32 PM »

I want lockers.
Front and back.
Every single jeep I have owned, has had lockers.
What good is one front and one rear wheel spinning??
I WANT 4WD.
Posted by: Carls_jeep
« on: March 17, 2013, 08:35:05 PM »

That's what I thought too. I have been quietly looking for a locker center section for my rear axle. I've been told you don't really want lockers on the front and rear.

Yes, that was a nice find and it's remarkable you could drive it out of it's resting place.
Posted by: Kenny_Kustom
« on: March 17, 2013, 08:23:14 PM »

Aww.
I thought this was going to be about lockers.
Not locking hubs.
I need a pair of lockers..
Posted by: ZekeD
« on: March 17, 2013, 12:48:30 PM »

Thanks Bob,

It was a Bramble find.   Here in the northwest if youstop moving they will find you.  It sat for 15+ years and it tookmore than a week to free it from the mass of sticky, thorny, long-legged plant life that entomed it.  Fuel, oil, wd40, and pb blaster and it RUNS.....  Borrowed tires, and drove it outof the field.  Leaks like a sieve.  No brakes, just FUN.

Zeke D
Posted by: Bob W
« on: March 17, 2013, 07:02:46 AM »

Zeke,

Nice Jeep. Please post more photos!!!!!!!!!!!!!!!   :)
Posted by: garage gnome
« on: March 16, 2013, 12:16:11 PM »

What ever grease you have in your grease gun is just fine.
Posted by: ZekeD
« on: March 16, 2013, 11:50:52 AM »

Thanks,  They are dualmatic hubs.    And the tip IS everything I need to know,  except what grease to repack them with?

Zeke
Posted by: Comanche_County
« on: March 16, 2013, 11:44:57 AM »

There's some good info on the tech page for hubs.  http://www.cj3apage.com/index/Tech_Tips.htm

Posted by: ZekeD
« on: March 16, 2013, 11:25:07 AM »

I have a '49 CJ3A with PTO winch and am in the 'inspection' phase of coming to terms with it.
The front locking hubs are VERY dirty, and I was wondering if there was a preferred way to
free them up. �They are the old (?) lever type.