The CJ3A Page CJ3B.info

Post reply

Warning: this topic has not been posted in for at least 120 days.
Unless you're sure you want to reply, please consider starting a new topic.

Note: this post will not display until it's been approved by a moderator.

Name:
Email:
Subject:
Message icon:
Verification:
Type the letters shown in the picture
Listen to the letters / Request another image

Type the letters shown in the picture:
Write the word between words Jeep from this JeepWILLYSJeep?:
How many slot has a GPW grill?  7 - 9 - 11:

shortcuts: hit alt+s to submit/post or alt+p to preview


Topic Summary

Posted by: Ryan_M
« on: May 28, 2013, 08:23:54 PM »

Quote
What exact 6v bulb did you buy?� Is there a brand and part number?

I bought mine here:

http://waltersworkshop.com/directional-bulbs.html

They are the 1156 "Short Globe Bulb Clear".

I'm not sure what the actual brand is. The base of each bulb is stamped "CPI B1006-6V China M8"

I bought 10 so I won't have to worry about them again for awhile....
Posted by: Uncle_Vin
« on: May 28, 2013, 05:17:31 PM »

What exact 6v bulb did you buy?  Is there a brand and part number?
Posted by: Ryan_M
« on: April 24, 2013, 10:47:23 AM »

Quote
Does anyone has an answer for 6 volts bulb?

The ones I bought are 6V.
Posted by: Quebec Jeep
« on: April 24, 2013, 10:25:56 AM »

Does anyone has an answer for 6 volts bulb?
Posted by: garage gnome
« on: April 22, 2013, 08:29:48 PM »

Yep, I got some stubby ones too from a local Harley dealer. They fit and work great. I like the looks without the spacers I had too.
Posted by: Ryan_M
« on: April 22, 2013, 08:21:11 PM »

Got my clear stubby dual filament bulbs from Walter's Workshop today. They fit as hoped which means no more bezel spacers. Turn signal project finally scratched off the list.
Posted by: garage gnome
« on: April 19, 2013, 07:20:22 PM »

Hmmm, I might need to get some. This would look much better!
Posted by: Kenny_Kustom
« on: April 19, 2013, 08:44:53 AM »

Quote
That's very encouraging. �I have the guy from Walter's Workshop (the link you posted here on this thread) supposedly ordering me some. Just an FYI - There's a cork gasket that goes on after the lens. Walck's carries them. If you install one of those on each light you can get rid of your o-rings and have a better chance of keeping the whole thing a little more water resistant.


Any Harley Davidson shop can get them, if he cant.


Thanks for the gasket tip !! I didn't know !!!
Posted by: Ryan_M
« on: April 19, 2013, 08:26:22 AM »

That's very encouraging.  I have the guy from Walter's Workshop (the link you posted here on this thread) supposedly ordering me some. Just an FYI - There's a cork gasket that goes on after the lens. Walck's carries them. If you install one of those on each light you can get rid of your o-rings and have a better chance of keeping the whole thing a little more water resistant.
Posted by: Kenny_Kustom
« on: April 19, 2013, 08:16:55 AM »


I used a couple o rings on the screws to keep the lens tight.






Everything works. Retained marker light function, and now have signals !!! Please don't hit me !! IM TURNING !!! SEE !!!???
Posted by: Kenny_Kustom
« on: April 19, 2013, 08:16:03 AM »


Got it all...
Part number from Harley is 2060-0026 12V


Installed.



Posted by: Kenny_Kustom
« on: April 17, 2013, 03:07:17 PM »

Got the flat stubby led's.. Too big..
Still waiting on the B1007A from Harley..
Posted by: Kenny_Kustom
« on: April 11, 2013, 08:56:41 PM »

I also ordered a pair of stubby led 1157's. I'll wire everything up with the normal 1157 bulbs, to verify operation of the signals, then swap in the LED's. I'll see what happens in 7-11 business days when they arrive... �::)


B1007A is a good part number for the short globe, dual filament bulb.
I ordered 4 of them from the local Harley shop.
Posted by: johnrb3b
« on: April 11, 2013, 11:45:26 AM »

For 6V, double filament, try 1154, 1158 or 1188
Posted by: johnrb3b
« on: April 11, 2013, 11:35:38 AM »

Quote
I have three LED's and a HD flasher for sale cheap if anyone wants to take over �;D
If they were 12V, I'd take you up on it, but none of my Jeeps are still 6V.
If nobody wants to buy them off you, would you be interested in loaning them to me (I'll pay shipping) so I can do some tests on them. I'd like to measure some of the characteristics of those LEDs from Superbright. I'm thinking of using them for my '57 Wagon.

The Superbright web site doesn't go into data like reverse leakage and such. I'd like to make my own measurements for future (and others') reference.

PM me if you're interested.