The CJ3A Page CJ3B.info

Post reply

Warning: this topic has not been posted in for at least 120 days.
Unless you're sure you want to reply, please consider starting a new topic.

Note: this post will not display until it's been approved by a moderator.

Name:
Email:
Subject:
Message icon:

Verification:
Type the letters shown in the picture
Listen to the letters / Request another image

Type the letters shown in the picture:
Write the word between words Jeep from this JeepWILLYSJeep?:
How many slot has a GPW grill?  7 - 9 - 11:

shortcuts: hit alt+s to submit/post or alt+p to preview


Topic Summary

Posted by: Gunslinger
« on: April 18, 2013, 04:53:56 PM »

Glad your back Scout, its a lonelier world without you
Posted by: Macgraham
« on: April 18, 2013, 09:45:31 AM »

Steady as she goes, Glad to see you back. :)
Posted by: johnrb3b
« on: April 18, 2013, 09:01:38 AM »

Good to see you're OK.
As to your question, yes it is very possible to over-use any electrical cleaner, contact "enhancer", lubricant, etc.
I suspect it didn't actually saturate any "paper" (fiber) parts of the generator, but it may have caused many low resistance leakage paths until it finally dried out.

This is why, even though I use them all the time, I don't actually like sprays.
My electronic contact cleaner of choice is Cramolin (now called DeoxIt).
http://www.caig.com
It is by far the best I've ever used in over 25 years of commercial electronics service on computer controlled manufacturing machinery. Whenever possible, I use the liquid form, applied with a brush, Q tip or even a piece of paper. I spray it at the paper and then use the paper on relay contacts and such.
Their rule is:
"The less you use, the better."
Or
"If a little is good, less is better."

That rule can be applied to most sprays.

Glad to hear things are working out. Keep us posted.
Posted by: garage gnome
« on: April 18, 2013, 07:29:18 AM »

Glad you are back! Hopefully everything settles down for you.
Posted by: scoutpilot
« on: April 18, 2013, 05:51:11 AM »

My problems aren't over yet. The dust has settled to the point where I have been able to get my bearing and proceed back on course, at least for now.
Posted by: calvinhunt
« on: April 18, 2013, 12:47:35 AM »

scoutpilot,
 ï¿½It's really good to have you back. �I must say, you had us a bit worried. � :-/
Posted by: scoutpilot
« on: April 17, 2013, 08:21:12 PM »

I want you all to ponder a theory. Is it possible to spray so much electrical cleaner into a generator that you drown it, soaking the paper wrapping the armature and it takes over a week to dry out. In that week you try to drive the Jeep you installed that genny on. The motor gives you fits. You make arrangements to go see the local Vintage Allis-Chalmers Doctor. He has nine of them in a garage at his shop and a tenth one in progress. It's been ten days now. You start the old girl up and you notice something is different today. It is a mile and a half to the Dr.'s shop. You smoothly accelerate through the gears and reach 45 mph without a problem. WTH? Long story short, the Dr tells you that your motor needs a complete overhaul His side $750, you supply the overhaul kit, then add the machine shop charges for what they do and replacing the valve guides. You say thanks, I need to save up some cash for that and you go home. Then you drive the Jeep to Walmart and back home without a problem. Then you drive to NAPA for a tool for your Ferd250 (Front, outer U-joints on an early D50 IFS from Canada) and return home. NO PROBLEMs.

Ya'll tell me. Yeah. I'm picking up where I left off.

My heartfelt thanks to all who cared.
Posted by: F Bill
« on: April 08, 2013, 09:39:39 PM »

I agree, but you gotta respect his privacy. He said he �wouldn't reply to inquiries......

He's a good guy and an asset to the jeep boards he is on. He posted this at each one, so it isn't  a specific board problem.. I have a feeling it is something pretty serious and I am sure he doesn't mind being in peoples thoughts and prayers. Hopefully whatever is going on will not last long and he will be back with us again soon.

Posted by: athawk11
« on: April 08, 2013, 09:30:35 PM »

I'm worried about Rick.  This was so abrupt.  I hope he's okay.  I hope his family is too.  
Posted by: Quebec Jeep
« on: April 08, 2013, 08:24:25 AM »

Sorry to hear that. Good luck
Posted by: 1oldracer
« on: April 07, 2013, 11:58:53 PM »

I  was sad to read your post and hear that something bad had happened.  I have enjoyed reading what you have had to say and have learned a thing or two from your experiences with your Jeeps.  It would be nice to be able to lend a hand to help you now.  Whatever the trouble is, you can whip it.  Good Luck
Posted by: Carls_jeep
« on: April 07, 2013, 10:43:02 AM »

Sorry to hear about that but I hope you continue to post on the sites.
Posted by: gmcjr
« on: April 06, 2013, 10:50:06 PM »

From one jeeper to another, prayer sent, and God bless!
Posted by: garage gnome
« on: April 06, 2013, 10:30:50 PM »

Sorry to hear! I hope all the best for you!
Posted by: scoutpilot
« on: April 06, 2013, 04:01:54 PM »

Guys. I've been handed some very bad news. I cannot go into details. As of today I must suspend my participation in all things Jeep. My hiatus is undetermined at this point. I will be returning all work I have accepted and ask that you refrain from sending anything to me at this point. I will not respond to inquiries. God Bless you all.